It is a build product of `make pm5`, like the .bin next to it, and the
build recreates it, so the copy in the tree only went stale and made
every build touch it again.
Co-Authored-By: Claude Code <noreply@anthropic.com>
save_graphbuffer() and save_buffer8() calloc a copy, and the restore_*()
helpers only copy out of it, so every owner leaked its save state.
check_chiptype() lost 4 * g_GraphTraceLen bytes plus the packed demod
buffer on each online `lf search` (~2 MB after the COTAG probe), and the
Visa2000 demod leaked on every `lf search`, online or offline.
Add free_buffer_savestate() and call it after the last restore in
check_chiptype(), demodTI(), demodVisa2k(), demodzx(),
try_detect_modulation() and t55xx_psk_untrim_head(), including the
early-return and success paths that never restored.
Reported with the check_chiptype() diagnosis and fix by @BeheSQ.
Fixes#3675
Co-Authored-By: Grok Bot <noreply@users.noreply.github.com>
RF over CEP works now that the FPGA bitstream step is done - it was
never actually CEP-blocked. Note CMD_CEP_STATUS (Hardware Status
dashboard) and the real open bug (Read Hitag2 over CEP fails with
stale cached data, firmware-side). SPI bit-order/phase is confirmed,
not pending.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
For the Flipper Zero FAP's status page: hw status/CMD_STATUS replies
entirely via free-text Dbprintf packets the FAP's frame layer discards,
with nothing structured on the terminating ack. CMD_CEP_STATUS follows
the CMD_CAPABILITIES precedent instead - one binary cep_status_t reply
covering CEP handshake state, BWM battery telemetry, and a firmware
version string.
Always replies PM3_SUCCESS; fields for a feature this build lacks
(no WITH_CEP, no WITH_BWM_STATUS) read as zero rather than failing the
command, so any client can call it unconditionally. cep_attached isn't
included yet - its getter (cep_is_attached()) only exists on the
not-yet-merged WFI-skip responsiveness branch (#3687); can be appended
later following capabilities_t's own append-only convention.
Stacked on the pm5-bwm-battery-telemetry branch (CMD_PM5_BWM_GET_BATTERY),
which this command's battery field reuses via bwm_read_battery_info().
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
The Flipper master only clocks the bus in bursts roughly every ~120ms
(its own idle poll cadence). CEP_SPI_BYTE_TIMEOUT (~3-10ms real time)
is ~20x shorter than that gap, so cep_spi_write_sync()'s first reply
byte - the one racing against the master's next poll - was giving up
long before the master actually showed up. Measured CEP reply success
at ~22% before this fix, ~100% after, across repeated LA-captured test
runs.
Fix: a separate, ~20x longer timeout (CEP_SPI_HEADER_BYTE_TIMEOUT) used
only for the first two length-header bytes of a reply - the ones that
can land in the gap. Every byte after that stays on the short timeout,
since once the master starts clocking it stays mid-CS and keeps going.
Also makes cep_spi_data_available() call cep_spi_resync() on its two
existing desync-evidence paths (sync-preamble discard overflow, an
implausible length header) instead of just returning false - those are
exactly the AT32 errata ES0003 corruption cep_spi_resync() already
exists to recover from; silently returning false left SPI1 in that bad
state until a later CRC/length check happened to catch it.
Stacked on fix-cep-spi-reliability (#3686, open) - this builds directly
on cep_spi_resync()/cep_spi_wait_tdbe()'s bounded-wait rewrite from that
PR and can't be tested standalone without it.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
bwm_charger.h is an armsrc-only header included after pm3_cmd.h in
appmain.c, so a struct embedding bwm_battery_info_t by value (e.g. a
future PM5 status command) couldn't see the type at the point it's
needed. bwm_ble_status_t and bwm_autooff_status_t already live in
pm3_cmd.h for the same reason - this just brings
bwm_battery_info_t in line with them. bwm_charger.c/.h keep their
function declarations unchanged; only the struct's home moves.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
hw status's battery/BWM section (bwm_print_battery_status()) only ever
formats its numbers into free-text Dbprintf lines, unusable by any
embedded/non-terminal client. Add a new command that returns the same
SoC/voltage/current/capacity/temp/health/fault numbers as one small
packed struct via reply_ng().
Refactor the shared reads into bwm_read_battery_info() so hw status
and the new command read the same values and can't drift apart -
hw status keeps all its existing charger-detail lines (MainCtl, input
limit, VIN_DPM, charge voltage/enable) unchanged, sourced from its own
reads as before; only the fuel-gauge numbers and the two small
charger-status reads the new struct needs are now shared.
Motivated by wanting a Flipper Zero FAP battery-status test screen
(separate app repo), but this command is generic and usable by any
client, not CEP-specific.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Flipper link can't interrupt a running reader loop
Problem: triggering the Flipper FAP's built-in ReadHitag2 demo command
turns the RF field on and it stays on even after backing out of the
app - only an unrelated USB command clears it. data_available()
(armsrc/util.c) is the standard idiom LF/HF reader loops use to notice
an incoming CMD_BREAK_LOOP, but it only polled USB/BWM/FPC. CEP's own
transport PR never wired it in, so a Flipper-sent break is invisible
to any loop that was already running.
Fix: add cep_spi_rx_pending() to armsrc/pm5_cep.c/.h - a genuinely
non-blocking single SPI1 RDBF flag check, not a reuse of the existing
(bounded-wait) cep_spi_data_available(), since this gets called every
iteration of every reader loop in the codebase and needs to cost
nothing when idle. Wire it into data_available()/data_available_fast()
alongside the existing BWM/FPC branches, additive since CEP and BWM
can coexist.
Hardware-confirmed: field now drops promptly every cycle instead of
sticking on, across repeated ReadHitag2 attach/attempt/cancel cycles.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Problem
pm5_power_idle()'s WFI sleep adds ~40-50ms of latency before the main
loop notices a fresh byte on CEP's SPI1/USART1. At idle this is the
whole point of WFI - but it's also what made the original attach
handshake miss bytes (GH #3667): cep_attach_poll() runs every 50ms, and
WFI's own latency on top of that was enough to lose bytes of the
Flipper's one-shot handshake string often enough to require a physical
cable replug to recover.
Change
armsrc/appmain.c: skip pm5_power_idle() entirely once cep_is_attached()
is true, so the main loop polls CEP as fast as the hardware allows for
as long as a Flipper is physically present.
armsrc/pm5_cep.c/.h: new cep_is_attached(), true as soon as the CC
controller reports a physical attach - independent of whether the
handshake/SPI transport is actually up yet, so the loop stops sleeping
before the handshake even starts, not after. Paired with a
CEP_ACTIVITY_TIMEOUT_MS (3000ms) idle-detach: the FAP quitting doesn't
touch the CC controller's attach bit (the cable stays connected), so
losing its normal 20-120ms SPI poll cadence for this long is what
actually means it's gone - at that point cep_is_attached() still
reflects the physical attach correctly, but cep_is_active() (and
therefore this PR's WFI-skip, which gates on attachment rather than a
completed handshake) only backs off once the FAP itself has clearly quit
rather than just being between polls.
Built on top of the AT32 SPI1 errata fix (bounded waits + resync) from
the companion CEP-reliability PR - running the main loop flat-out
against an unbounded wait would have just hit that hang faster, which is
why this shipped after rather than alongside it.
Behaviour change
PM5 no longer downclocks to WFI between main-loop iterations while a
Flipper is attached over CEP (idle power draw increases for the duration
of the attach; unaffected when no Flipper is present, and unaffected on
RDV4/non-CEP builds).
Testing
- make clean && make PLATFORM=PM5 PLATFORM_EXTRAS=BWM and
make clean && make PLATFORM=PM3RDV4 - both zero warnings.
- Hardware: this flag was active throughout all of the companion CEP-
reliability PR's hardware testing (60s/110s/240s captures, 18x
`hw status`, 5x attach/detach + `hf search` cycles against a real
card) - all passed with WFI-skip engaged the whole time. Additionally
reflashed this exact branch standalone and reconfirmed a live
attach/detach cycle completes cleanly.
- Not tested: clang toolchain (firmware-only diff); idle power draw was
not independently measured (no direct ammeter in this session's
bench setup, only observed BWM telemetry prior to this change).
Checklist
- [x] Proper style of own code, no unrelated reformatting included
- [x] Builds warning-free with gcc (PM5 and RDV4)
- [ ] clang not tried (firmware-only diff)
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>