FPGA: Add source files specific to PM5.

This commit is contained in:
dxl committed 2026-10-12 00:04:06 +08:00
1 parent 7d5dd46d94
commit 256aca63b7
4 files changed
+913

No files matched your search

+382
View File
@@ -0,0 +1,382 @@
//-----------------------------------------------------------------------------
// Copyright (C) Proxmark3 contributors. See AUTHORS.md for details.
//
// This program is free software: you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation, either version 3 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// See LICENSE.txt for the text of the license.
//-----------------------------------------------------------------------------
//
// The FPGA is responsible for interfacing between the A/D, the coil drivers,
// and the ARM. In the low-frequency modes it passes the data straight
// through, so that the ARM gets raw A/D samples over the SSP. In the high-
// frequency modes, the FPGA might perform some demodulation first, to
// reduce the amount of data that we must send to the ARM.
//-----------------------------------------------------------------------------
module fpga_hf(
input ck_1356meg,
input spck,
//input pck0,
input ncs,
input [7:0] adc_d,
//input cross_hi,
//input cross_lo,
input mosi,
input ssp_dout,
input ce, // 复位输入,常态高
output ssp_din,
output ssp_frame,
output ssp_clk,
output adc_clk,
//output adc_noe,
output miso,
output pwr_lo,
output pwr_hi,
output pwr_oe1,
output pwr_oe2,
//output pwr_oe3,
output pwr_oe4,
output dbg,
output reg [11:0] pwm_duty = 12'h800
);
// In all modes, let the ADC's outputs be enabled.
//assign adc_noe = 1'b0;
assign miso = 1'bZ;
wire cross_hi = 1'b0;
wire [2:0] major_mode;
assign major_mode = ce ? conf_word[8:6] : 3'b111;
//-----------------------------------------------------------------------------
// The SPI receiver. This sets up the configuration word, which the rest of
// the logic looks at to determine how to connect the A/D and the coil
// drivers (i.e., which section gets it). Also assign some symbolic names
// to the configuration bits, for use below.
//-----------------------------------------------------------------------------
// Receive 16bits of data from ARM here.
reg [15:0] shift_reg;
//always @(posedge spck) if (~ncs) shift_reg <= {shift_reg[14:0], mosi};
always @(posedge spck) begin
if(~ncs & ce)
shift_reg <= {shift_reg[14:0], mosi};
end
reg trace_enable;
reg [5:0] hf_edge_detect_threshold = 6'd7;
reg [5:0] hf_edge_detect_threshold_high = 6'd20;
reg [8:0] conf_word;
initial
begin
hf_edge_detect_threshold <= 7;
hf_edge_detect_threshold_high <= 20;
end
// We switch modes between transmitting to the 13.56 MHz tag and receiving
// from it, which means that we must make sure that we can do so without
// glitching, or else we will glitch the transmitted carrier.
always @(posedge ncs)
begin
if(ce) begin
// 4 bit command
case (shift_reg[15:12])
`FPGA_CMD_SET_CONFREG: conf_word <= shift_reg[8:0];
`FPGA_CMD_TRACE_ENABLE: trace_enable <= shift_reg[0];
`FPGA_CMD_SET_EDGE_DETECT_THRESHOLD:
begin
hf_edge_detect_threshold <= shift_reg[5:0];
hf_edge_detect_threshold_high <= shift_reg[11:6];
end
`FPGA_CMD_SET_PWR_PWM_LOW_COUNT:pwm_duty <= shift_reg[11:0];
endcase
end
end
//-----------------------------------------------------------------------------
// And then we instantiate the modules corresponding to each of the FPGA's
// major modes, and use muxes to connect the outputs of the active mode to
// the output pins.
//-----------------------------------------------------------------------------
// HF reader
hi_reader hr(
.ck_1356meg (ck_1356meg),
.adc_d (adc_d),
.subcarrier_frequency (conf_word[5:4]),
.minor_mode (conf_word[3:0]),
.ssp_dout (ssp_dout),
.ssp_din (mux0_ssp_din),
.ssp_frame (mux0_ssp_frame),
.ssp_clk (mux0_ssp_clk),
.adc_clk (mux0_adc_clk),
.pwr_lo (mux0_pwr_lo),
.pwr_hi (mux0_pwr_hi),
.pwr_oe1 (mux0_pwr_oe1),
.pwr_oe2 (mux0_pwr_oe2),
.pwr_oe3 (mux0_pwr_oe3),
.pwr_oe4 (mux0_pwr_oe4),
.debug (mux0_debug)
);
// HF simulated tag
hi_simulate hs(
.ck_1356meg (ck_1356meg),
.adc_d (adc_d),
.mod_type (conf_word[3:0]),
.ssp_dout (ssp_dout),
.ssp_din (mux1_ssp_din),
.ssp_frame (mux1_ssp_frame),
.ssp_clk (mux1_ssp_clk),
.adc_clk (mux1_adc_clk),
.pwr_lo (mux1_pwr_lo),
.pwr_hi (mux1_pwr_hi),
.pwr_oe1 (mux1_pwr_oe1),
.pwr_oe2 (mux1_pwr_oe2),
.pwr_oe3 (mux1_pwr_oe3),
.pwr_oe4 (mux1_pwr_oe4),
.debug (mux1_debug)
);
// HF ISO14443-A
hi_iso14443a hisn(
.ck_1356meg (ck_1356meg),
.adc_d (adc_d),
.mod_type (conf_word[3:0]),
.ssp_dout (ssp_dout),
.ssp_din (mux2_ssp_din),
.ssp_frame (mux2_ssp_frame),
.ssp_clk (mux2_ssp_clk),
.adc_clk (mux2_adc_clk),
.pwr_lo (mux2_pwr_lo),
.pwr_hi (mux2_pwr_hi),
.pwr_oe1 (mux2_pwr_oe1),
.pwr_oe2 (mux2_pwr_oe2),
.pwr_oe3 (mux2_pwr_oe3),
.pwr_oe4 (mux2_pwr_oe4),
.debug (mux2_debug),
.edge_detect_threshold ({5'b00000, hf_edge_detect_threshold}),
.edge_detect_threshold_high ({5'b00000, hf_edge_detect_threshold_high})
);
// HF sniff
hi_sniffer he(
.ck_1356meg (ck_1356meg),
.adc_d (adc_d),
.ssp_din (mux3_ssp_din),
.ssp_frame (mux3_ssp_frame),
.ssp_clk (mux3_ssp_clk),
.adc_clk (mux3_adc_clk),
.pwr_lo (mux3_pwr_lo),
.pwr_hi (mux3_pwr_hi),
.pwr_oe1 (mux3_pwr_oe1),
.pwr_oe2 (mux3_pwr_oe2),
.pwr_oe3 (mux3_pwr_oe3),
.pwr_oe4 (mux3_pwr_oe4)
);
// HF ISO18092 FeliCa
hi_flite hfl(
.ck_1356meg (ck_1356meg),
.adc_d (adc_d),
.mod_type (conf_word[3:0]),
.ssp_dout (ssp_dout),
.ssp_din (mux4_ssp_din),
.ssp_frame (mux4_ssp_frame),
.ssp_clk (mux4_ssp_clk),
.adc_clk (mux4_adc_clk),
.pwr_lo (mux4_pwr_lo),
.pwr_hi (mux4_pwr_hi),
.pwr_oe1 (mux4_pwr_oe1),
.pwr_oe2 (mux4_pwr_oe2),
.pwr_oe3 (mux4_pwr_oe3),
.pwr_oe4 (mux4_pwr_oe4),
.debug (mux4_debug)
);
// HF get trace
hi_get_trace gt(
.ck_1356megb (ck_1356meg),
.adc_d (adc_d),
.trace_enable (trace_enable),
.major_mode (major_mode),
.ssp_din (mux5_ssp_din),
.ssp_frame (mux5_ssp_frame),
.ssp_clk (mux5_ssp_clk)
);
// These assignments must agree with the defines in fpgaloader.h
// Major modes High Frequency
// mux0 = HF reader
// mux1 = HF simulated tag
// mux2 = HF ISO14443-A
// mux3 = HF sniff
// mux4 = HF ISO18092 FeliCa
// mux5 = HF get trace
// mux6 = unused
// mux7 = FPGA_MAJOR_MODE_OFF
mux8 mux_ssp_clk (
.sel (major_mode),
.y (ssp_clk ),
.x0 (mux0_ssp_clk ),
.x1 (mux1_ssp_clk ),
.x2 (mux2_ssp_clk ),
.x3 (mux3_ssp_clk ),
.x4 (mux4_ssp_clk ),
.x5 (mux5_ssp_clk ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_ssp_din (
.sel (major_mode),
.y (ssp_din ),
.x0 (mux0_ssp_din ),
.x1 (mux1_ssp_din ),
.x2 (mux2_ssp_din ),
.x3 (mux3_ssp_din ),
.x4 (mux4_ssp_din ),
.x5 (mux5_ssp_din ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_ssp_frame (
.sel (major_mode),
.y (ssp_frame ),
.x0 (mux0_ssp_frame ),
.x1 (mux1_ssp_frame ),
.x2 (mux2_ssp_frame ),
.x3 (mux3_ssp_frame ),
.x4 (mux4_ssp_frame ),
.x5 (mux5_ssp_frame ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_pwr_oe1 (
.sel (major_mode),
.y (pwr_oe1 ),
.x0 (mux0_pwr_oe1 ),
.x1 (mux1_pwr_oe1 ),
.x2 (mux2_pwr_oe1 ),
.x3 (mux3_pwr_oe1 ),
.x4 (mux4_pwr_oe1 ),
.x5 (1'b0 ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_pwr_oe2 (
.sel (major_mode),
.y (pwr_oe2 ),
.x0 (mux0_pwr_oe2 ),
.x1 (mux1_pwr_oe2 ),
.x2 (mux2_pwr_oe2 ),
.x3 (mux3_pwr_oe2 ),
.x4 (mux4_pwr_oe2 ),
.x5 (1'b0 ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_pwr_oe3 (
.sel (major_mode),
.y (pwr_oe3 ),
.x0 (mux0_pwr_oe3 ),
.x1 (mux1_pwr_oe3 ),
.x2 (mux2_pwr_oe3 ),
.x3 (mux3_pwr_oe3 ),
.x4 (mux4_pwr_oe3 ),
.x5 (1'b0 ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_pwr_oe4 (
.sel (major_mode),
.y (pwr_oe4 ),
.x0 (mux0_pwr_oe4 ),
.x1 (mux1_pwr_oe4 ),
.x2 (mux2_pwr_oe4 ),
.x3 (mux3_pwr_oe4 ),
.x4 (mux4_pwr_oe4 ),
.x5 (1'b0 ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_pwr_lo (
.sel (major_mode),
.y (pwr_lo ),
.x0 (mux0_pwr_lo ),
.x1 (mux1_pwr_lo ),
.x2 (mux2_pwr_lo ),
.x3 (mux3_pwr_lo ),
.x4 (mux4_pwr_lo ),
.x5 (1'b0 ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_pwr_hi (
.sel (major_mode),
.y (pwr_hi ),
.x0 (mux0_pwr_hi ),
.x1 (mux1_pwr_hi ),
.x2 (mux2_pwr_hi ),
.x3 (mux3_pwr_hi ),
.x4 (mux4_pwr_hi ),
.x5 (1'b0 ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_adc_clk (
.sel (major_mode),
.y (adc_clk ),
.x0 (mux0_adc_clk ),
.x1 (mux1_adc_clk ),
.x2 (mux2_adc_clk ),
.x3 (mux3_adc_clk ),
.x4 (mux4_adc_clk ),
.x5 (1'b0 ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_dbg (
.sel (major_mode),
.y (dbg ),
.x0 (mux0_debug ),
.x1 (mux1_debug ),
.x2 (mux2_debug ),
.x3 (1'b0 ),
.x4 (mux4_debug ),
.x5 (1'b0 ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
endmodule
+335
View File
@@ -0,0 +1,335 @@
//-----------------------------------------------------------------------------
// Copyright (C) Proxmark3 contributors. See AUTHORS.md for details.
//
// This program is free software: you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation, either version 3 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// See LICENSE.txt for the text of the license.
//-----------------------------------------------------------------------------
//
// The FPGA is responsible for interfacing between the A/D, the coil drivers,
// and the ARM. In the low-frequency modes it passes the data straight
// through, so that the ARM gets raw A/D samples over the SSP. In the high-
// frequency modes, the FPGA might perform some demodulation first, to
// reduce the amount of data that we must send to the ARM.
//-----------------------------------------------------------------------------
module fpga_lf(
//input ck_1356meg,
input spck,
input pck0,
input ncs,
input [7:0] adc_d,
input cross_lo,
input mosi,
input ssp_dout,
input ce, // 复位输入,常态高
output ssp_din,
output ssp_frame,
output ssp_clk,
output adc_clk,
output miso,
output pwr_lo,
output pwr_oe1,
output pwr_oe2,
output pwr_oe4,
output dbg,
output reg [11:0] pwm_duty = 12'h500
);
// In all modes, let the ADC's outputs be enabled.
//assign adc_noe = 1'b0;
assign miso = 1'bZ;
wire [2:0] major_mode;
assign major_mode = ce ? conf_word[8:6] : 3'b111;
//-----------------------------------------------------------------------------
// The SPI receiver. This sets up the configuration word, which the rest of
// the logic looks at to determine how to connect the A/D and the coil
// drivers (i.e., which section gets it). Also assign some symbolic names
// to the configuration bits, for use below.
//-----------------------------------------------------------------------------
// Receive 16bits of data from ARM here.
reg [15:0] shift_reg;
always @(posedge spck) begin
if(~ncs & ce)
shift_reg <= {shift_reg[14:0], mosi};
end
reg [7:0] lf_ed_threshold;
// adjustable frequency clock
wire [7:0] pck_cnt;
wire pck_divclk;
reg [7:0] divisor;
clk_divider div_clk(pck0, divisor, pck_cnt, pck_divclk);
reg [11:0] conf_word;
// We switch modes between transmitting to the 13.56 MHz tag and receiving
// from it, which means that we must make sure that we can do so without
// glitching, or else we will glitch the transmitted carrier.
always @(posedge ncs)
begin
if(ce) begin
// 4 bit command
case (shift_reg[15:12])
`FPGA_CMD_SET_CONFREG:
begin
// 12 bit data
conf_word <= shift_reg[11:0];
if (shift_reg[8:6] == `FPGA_MAJOR_MODE_LF_EDGE_DETECT) lf_ed_threshold <= 127; // default threshold
end
`FPGA_CMD_SET_DIVISOR:
divisor <= shift_reg[7:0]; // 8bits
`FPGA_CMD_SET_EDGE_DETECT_THRESHOLD:
lf_ed_threshold <= shift_reg[7:0]; // 8 bits
`FPGA_CMD_SET_PWR_PWM_LOW_COUNT:pwm_duty <= shift_reg[11:0];
endcase
end
end
//-----------------------------------------------------------------------------
// And then we instantiate the modules corresponding to each of the FPGA's
// major modes, and use muxes to connect the outputs of the active mode to
// the output pins.
//-----------------------------------------------------------------------------
// ############################################################################
// LF reader (generic)
lo_read lr(
.pck0 (pck0),
.pck_divclk (pck_divclk),
.pck_cnt (pck_cnt),
.adc_d (adc_d),
.lf_field (conf_word[0]),
.ssp_din (mux0_ssp_din),
.ssp_frame (mux0_ssp_frame),
.ssp_clk (mux0_ssp_clk),
.adc_clk (mux0_adc_clk),
.pwr_lo (mux0_pwr_lo),
.pwr_oe1 (mux0_pwr_oe1),
.pwr_oe2 (mux0_pwr_oe2),
.pwr_oe3 (mux0_pwr_oe3),
.pwr_oe4 (mux0_pwr_oe4),
.debug (mux0_debug)
);
// LF edge detect (generic)
lo_edge_detect le(
.pck0 (pck0),
.pck_divclk (pck_divclk),
.adc_d (adc_d),
.cross_lo (cross_lo),
.lf_field (conf_word[0]),
.lf_ed_toggle_mode (conf_word[1]),
.lf_ed_threshold (lf_ed_threshold),
.ssp_dout (ssp_dout),
.ssp_frame (mux1_ssp_frame),
.ssp_clk (mux1_ssp_clk),
.adc_clk (mux1_adc_clk),
.pwr_lo (mux1_pwr_lo),
.pwr_oe1 (mux1_pwr_oe1),
.pwr_oe2 (mux1_pwr_oe2),
.pwr_oe3 (mux1_pwr_oe3),
.pwr_oe4 (mux1_pwr_oe4),
.debug (mux1_debug)
);
// LF passthrough
lo_passthru lp(
.pck_divclk (pck_divclk),
.cross_lo (cross_lo),
.ssp_dout (ssp_dout),
.ssp_din (mux2_ssp_din),
.adc_clk (mux2_adc_clk),
.pwr_lo (mux2_pwr_lo),
.pwr_oe1 (mux2_pwr_oe1),
.pwr_oe2 (mux2_pwr_oe2),
.pwr_oe3 (mux2_pwr_oe3),
.pwr_oe4 (mux2_pwr_oe4),
.debug (mux2_debug)
);
// LF ADC (read/write)
lo_adc la(
.pck0 (pck0),
.adc_d (adc_d),
.divisor (divisor),
.lf_field (conf_word[0]),
.ssp_dout (ssp_dout),
.ssp_din (mux3_ssp_din),
.ssp_frame (mux3_ssp_frame),
.ssp_clk (mux3_ssp_clk),
.adc_clk (mux3_adc_clk),
.pwr_lo (mux3_pwr_lo ),
.pwr_oe1 (mux3_pwr_oe1),
.pwr_oe2 (mux3_pwr_oe2),
.pwr_oe3 (mux3_pwr_oe3),
.pwr_oe4 (mux3_pwr_oe4),
.debug (mux3_debug)
);
assign mux6_pwr_lo = 1'b1;
// 7 -- SPARE
// These assignments must agree with the defines in fpgaloader.h
// Major modes Low Frequency
// mux0 = LF reader (generic)
// mux1 = LF edge detect (generic)
// mux2 = LF passthrough
// mux3 = LF ADC (read/write)
// mux4 = SPARE
// mux5 = SPARE
// mux6 = SPARE
// mux7 = FPGA_MAJOR_MODE_OFF
mux8 mux_ssp_clk (
.sel (major_mode),
.y (ssp_clk ),
.x0 (mux0_ssp_clk ),
.x1 (mux1_ssp_clk ),
.x2 (1'b0 ),
.x3 (mux3_ssp_clk ),
.x4 (1'b0 ),
.x5 (1'b0 ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_ssp_din (
.sel (major_mode),
.y (ssp_din ),
.x0 (mux0_ssp_din ),
.x1 (1'b0 ),
.x2 (mux2_ssp_din ),
.x3 (mux3_ssp_din ),
.x4 (1'b0 ),
.x5 (1'b0 ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_ssp_frame (
.sel (major_mode),
.y (ssp_frame ),
.x0 (mux0_ssp_frame ),
.x1 (mux1_ssp_frame ),
.x2 (1'b0 ),
.x3 (mux3_ssp_frame ),
.x4 (1'b0 ),
.x5 (1'b0 ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_pwr_oe1 (
.sel (major_mode),
.y (pwr_oe1 ),
.x0 (mux0_pwr_oe1 ),
.x1 (mux1_pwr_oe1 ),
.x2 (mux2_pwr_oe1 ),
.x3 (mux3_pwr_oe1 ),
.x4 (1'b0 ),
.x5 (1'b0 ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_pwr_oe2 (
.sel (major_mode),
.y (pwr_oe2 ),
.x0 (mux0_pwr_oe2 ),
.x1 (mux1_pwr_oe2 ),
.x2 (mux2_pwr_oe2 ),
.x3 (mux3_pwr_oe2 ),
.x4 (1'b0 ),
.x5 (1'b0 ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_pwr_oe3 (
.sel (major_mode),
.y (pwr_oe3 ),
.x0 (mux0_pwr_oe3 ),
.x1 (mux1_pwr_oe3 ),
.x2 (mux2_pwr_oe3 ),
.x3 (mux3_pwr_oe3 ),
.x4 (1'b0 ),
.x5 (1'b0 ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_pwr_oe4 (
.sel (major_mode),
.y (pwr_oe4 ),
.x0 (mux0_pwr_oe4 ),
.x1 (mux1_pwr_oe4 ),
.x2 (mux2_pwr_oe4 ),
.x3 (mux3_pwr_oe4 ),
.x4 (1'b0 ),
.x5 (1'b0 ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_pwr_lo (
.sel (major_mode),
.y (pwr_lo ),
.x0 (mux0_pwr_lo ),
.x1 (mux1_pwr_lo ),
.x2 (mux2_pwr_lo ),
.x3 (mux3_pwr_lo ),
.x4 (1'b0 ),
.x5 (1'b0 ),
.x6 (mux6_pwr_lo ),
.x7 (1'b0 )
);
mux8 mux_adc_clk (
.sel (major_mode),
.y (adc_clk ),
.x0 (mux0_adc_clk ),
.x1 (mux1_adc_clk ),
.x2 (mux2_adc_clk ),
.x3 (mux3_adc_clk ),
.x4 (1'b0 ),
.x5 (1'b0 ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
mux8 mux_dbg (
.sel (major_mode),
.y (dbg ),
.x0 (mux0_debug ),
.x1 (mux1_debug ),
.x2 (mux2_debug ),
.x3 (mux3_debug ),
.x4 (1'b0 ),
.x5 (1'b0 ),
.x6 (1'b0 ),
.x7 (1'b0 )
);
endmodule
+132
View File
@@ -0,0 +1,132 @@
module fpga_top (
input ck_1356meg,
input ck_1356meg_b, // B is for close range wiring
input spi_sck,
input pck0,
input spi_ncs,
input [9:0] adc_d,
input cross_lo,
input spi_mosi,
input ssp_dout,
input module_sel, // 选择模块,1=HF,0=LF
output ssp_din,
output ssp_frame,
output ssp_clk,
output adc_clk,
output spi_miso,
output pwr_lo,
output pwr_hi,
output pwr_oe1,
output pwr_oe2,
output pwr_oe4,
output dbg1,
output dbg2,
output dbgled,
output clk_gate, //门控输出,控制切断外部13.56m
output pwr_pwm, //升压器输出,pwm控制升压电压
output pan_en, //模拟供电使能
output pdp_en //升压器使能
);
wire ce_lf = ~module_sel; //高启用,低重置
wire ce_hf = module_sel; //高启用,低重置
//-----------------------------------------GATE-------------------------
//门控使能信号同步到输入时钟域,避免亚稳态
reg gate_en_sync1, gate_en_sync2;
always @(posedge ck_1356meg) begin
gate_en_sync1 <= gate_en;
gate_en_sync2 <= gate_en_sync1;
end
assign clk_gate = ~gate_en_sync2;//这里取反是因为外部门控是低有效的
//-----------------------------------------PWM--------------------------
Gowin_rPLL pwr_pwm_pll(
.clkout(pwr_pwm_pll_clko), //output clkout
.clkin(ck_1356meg) //input clkin
);
wire [11:0] pwm_duty_lf; // LF 模块的 PWM 占空比输出
wire [11:0] pwm_duty_hf; // HF 模块的 PWM 占空比输出
wire [11:0] pwm_duty; // PWM占空比,实际上是高电平长度,和4096做比例
reg [11:0] pwm_cnt= 12'h0;
always @(posedge pwr_pwm_pll_clko) pwm_cnt <= pwm_cnt + 1'b1; //计数器
assign pwr_pwm = (pwm_cnt > pwm_duty); //pwm输出
assign pan_en = 1'b1;
assign pdp_en = 1'b1;
assign pwr_hi = 1'bZ; //使用外部门控时禁用PWRHI,由于是并联的,需要高阻
assign dbgled = 1'b1;
assign dbg2 = 1'bZ; // 未使用
fpga_lf uut_lf (
.pck0(pck0),
.spck(spi_sck),
.ncs(spi_ncs),
.adc_d(adc_d[9:2]),
.cross_lo(cross_lo),
.mosi(spi_mosi),
.ssp_dout(ssp_dout),
.ce(ce_lf),
.ssp_din(ssp_din_lf),
.ssp_frame(ssp_frame_lf),
.ssp_clk(ssp_clk_lf),
.adc_clk(adc_clk_lf),
.miso(miso_lf),
.pwr_lo(pwr_lo_lf),
.pwr_oe1(pwr_oe1_lf),
.pwr_oe2(pwr_oe2_lf),
.pwr_oe4(pwr_oe4_lf),
.dbg(dbg_lf),
.pwm_duty(pwm_duty_lf)
);
fpga_hf uut_hf (
.ck_1356meg(ck_1356meg),
.spck(spi_sck),
.ncs(spi_ncs),
.adc_d(adc_d[9:2]),
.mosi(spi_mosi),
.ssp_dout(ssp_dout),
.ce(ce_hf),
.ssp_din(ssp_din_hf),
.ssp_frame(ssp_frame_hf),
.ssp_clk(ssp_clk_hf),
.adc_clk(adc_clk_hf),
.miso(miso_hf),
.pwr_lo(pwr_lo_hf),
.pwr_hi(gate_en),
.pwr_oe1(pwr_oe1_hf),
.pwr_oe2(pwr_oe2_hf),
.pwr_oe4(pwr_oe4_hf),
.dbg(dbg_hf),
.pwm_duty(pwm_duty_hf)
);
assign ssp_din = ~module_sel ? ssp_din_lf : ssp_din_hf;
assign ssp_frame = ~module_sel ? ssp_frame_lf : ssp_frame_hf;
assign ssp_clk = ~module_sel ? ssp_clk_lf : ssp_clk_hf;
assign adc_clk = ~module_sel ? adc_clk_lf : adc_clk_hf;
assign spi_miso = ~module_sel ? miso_lf : miso_hf;
assign pwr_lo = ~module_sel ? pwr_lo_lf : pwr_lo_hf;
//assign pwr_hi = ~module_sel ? pwr_hi_lf : pwr_hi_hf;
assign pwr_oe1 = ~module_sel ? pwr_oe1_lf : pwr_oe1_hf;
assign pwr_oe2 = ~module_sel ? pwr_oe2_lf : pwr_oe2_hf;
assign pwr_oe4 = ~module_sel ? pwr_oe4_lf : pwr_oe4_hf;
assign dbg1 = ~module_sel ? dbg_lf : dbg_hf;
assign pwm_duty = ~module_sel ? pwm_duty_lf : pwm_duty_hf;
endmodule
+64
View File
@@ -0,0 +1,64 @@
//Copyright (C)2014-2023 Gowin Semiconductor Corporation.
//All rights reserved.
//File Title: IP file
//Tool Version: V1.9.9 (64-bit)
//Part Number: GW1N-UV4QN48C6/I5
//Device: GW1N-4
//Device Version: D
//Created Time: Mon Jul 6 18:07:08 2026
module Gowin_rPLL (clkout, clkin);
output clkout;
input clkin;
wire lock_o;
wire clkoutp_o;
wire clkoutd_o;
wire clkoutd3_o;
wire gw_gnd;
assign gw_gnd = 1'b0;
rPLL rpll_inst (
.CLKOUT(clkout),
.LOCK(lock_o),
.CLKOUTP(clkoutp_o),
.CLKOUTD(clkoutd_o),
.CLKOUTD3(clkoutd3_o),
.RESET(gw_gnd),
.RESET_P(gw_gnd),
.CLKIN(clkin),
.CLKFB(gw_gnd),
.FBDSEL({gw_gnd,gw_gnd,gw_gnd,gw_gnd,gw_gnd,gw_gnd}),
.IDSEL({gw_gnd,gw_gnd,gw_gnd,gw_gnd,gw_gnd,gw_gnd}),
.ODSEL({gw_gnd,gw_gnd,gw_gnd,gw_gnd,gw_gnd,gw_gnd}),
.PSDA({gw_gnd,gw_gnd,gw_gnd,gw_gnd}),
.DUTYDA({gw_gnd,gw_gnd,gw_gnd,gw_gnd}),
.FDLY({gw_gnd,gw_gnd,gw_gnd,gw_gnd})
);
defparam rpll_inst.FCLKIN = "13.56";
defparam rpll_inst.DYN_IDIV_SEL = "false";
defparam rpll_inst.IDIV_SEL = 1;
defparam rpll_inst.DYN_FBDIV_SEL = "false";
defparam rpll_inst.FBDIV_SEL = 58;
defparam rpll_inst.DYN_ODIV_SEL = "false";
defparam rpll_inst.ODIV_SEL = 2;
defparam rpll_inst.PSDA_SEL = "0000";
defparam rpll_inst.DYN_DA_EN = "false";
defparam rpll_inst.DUTYDA_SEL = "1000";
defparam rpll_inst.CLKOUT_FT_DIR = 1'b1;
defparam rpll_inst.CLKOUTP_FT_DIR = 1'b1;
defparam rpll_inst.CLKOUT_DLY_STEP = 0;
defparam rpll_inst.CLKOUTP_DLY_STEP = 0;
defparam rpll_inst.CLKFB_SEL = "internal";
defparam rpll_inst.CLKOUT_BYPASS = "false";
defparam rpll_inst.CLKOUTP_BYPASS = "false";
defparam rpll_inst.CLKOUTD_BYPASS = "false";
defparam rpll_inst.DYN_SDIV_SEL = 2;
defparam rpll_inst.CLKOUTD_SRC = "CLKOUT";
defparam rpll_inst.CLKOUTD3_SRC = "CLKOUT";
defparam rpll_inst.DEVICE = "GW1N-4D";
endmodule //Gowin_rPLL