FPGA: hi_flite.v merged.

This commit is contained in:
dxl committed 2026-10-09 17:14:53 +08:00
1 parent b1795a9e7e
commit 2d3de66488
1 file changed
+24 -2
+24 -2
View File
@@ -110,24 +110,42 @@ always @(posedge adc_clk)
//maybe change it so that ARM sends preamble as well.
//then: ready bits sent to ARM, 8 bits sent from ARM (all ones), then preamble (all zeros, presumably) - which starts modulation
// SSP(FRAME_H) ~speed -> 9'd31 speed -> 8'd15
// SSP(FRAME_L) ~speed -> 9'b1011111(d95 OF 512) speed -> 8'b101111(d47 OF 256)
// TIMODE(FRAME_H) ~speed -> 9'd(512-64) speed -> 8'd(256-32)
// TIMODE(FRAME_L) ~speed -> 9'b0 speed -> 8'b0
`ifdef WITH_TIMODE
`define FRAME_SET_L 9'd448
`define FRAME_SET_H 8'd224
`define FRAME_CLR_L 9'd0
`define FRAME_CLR_H 8'd0
`else
`define FRAME_SET_L 9'd31
`define FRAME_SET_H 8'd15
`define FRAME_CLR_L 9'b1011111 // 95 = 96 - 1
`define FRAME_CLR_H 8'b101111 // 47 = 48 - 1
`endif
always @(negedge adc_clk)
begin
//count fc/64 - transfer bits to ARM at the rate they are received
//At speed 0, clk rises at 0 or 64; at speed 1, clk rises at 0 or 32.
if( ((~speed) && (ssp_cnt[5:0] == 6'b000000) ) || (speed && (ssp_cnt[4:0] == 5'b00000)) )
begin
ssp_clk <= 1'b1;
//send current bit (detected in SNIFF mode or the one being modulated in MOD mode, 0 otherwise)
ssp_din <= curbit;
end
// At speed 0, clk falls at 32; at speed 1, clk falls at 16.
if( ( (~speed) && (ssp_cnt[5:0] == 6'b100000)) ||(speed && ssp_cnt[4:0] == 5'b10000))
ssp_clk <= 1'b0;
//create frame pulses. TBH, I still don't know what they do exactly, but they are crucial for ARM->FPGA transfer. If the frame is in the beginning of the byte, transfer slows to a crawl for some reason
// took me a day to figure THAT out.
if(( (~speed) && (ssp_cnt[8:0] == 9'd31)) || (speed && ssp_cnt[7:0] == 8'd15))
if(( (~speed) && (ssp_cnt[8:0] == `FRAME_SET_L)) || (speed && ssp_cnt[7:0] == `FRAME_SET_H))
begin
ssp_frame <= 1'b1;
end
if(( (~speed) && (ssp_cnt[8:0] == 9'b1011111)) || (speed &&ssp_cnt[7:0] == 8'b101111) )
if(( (~speed) && (ssp_cnt[8:0] == `FRAME_CLR_L)) || (speed && ssp_cnt[7:0] == `FRAME_CLR_H))
begin
ssp_frame <= 1'b0;
end
@@ -348,7 +366,11 @@ always @(ck_1356meg or ssp_dout or power or disabl or mod)
begin
if (power)
begin
`ifdef PM5 // pwr_hi is used to control the 1356 clk enable on PM5, not clk output.
pwr_hi <= 1'b1; // enable 1356 clk output
`else
pwr_hi <= ck_1356meg;
`endif
pwr_lo <= 1'b0;
pwr_oe1 <= 1'b0;//mod;
pwr_oe2 <= 1'b0;//mod;