Files
RP2040-Decoder/core1.c
T

211 lines
8.1 KiB
C

//////////////////////////
// RP2040-Decoder //
// Gabriel Koppenstein //
// core1.c //
//////////////////////////
#include "core1.h"
uint16_t current_target = 0;
float current_target_voltage = 0;
struct repeating_timer pid_control_timer,speed_helper_timer;
typedef struct pid_params{
float k_p;
float t_s;
float a_1;
float a_2;
float sum_limit_max;
float sum_limit_min;
float output;
float e;
float e_prev;
float e_sum;
uint startup_offset_fwd;
uint startup_offset_rev;
bool direction_prev;
}pid_params;
pid_params pid;
typedef struct measure_params{
uint8_t delay_in_us;
uint8_t total_iterations;
uint8_t left_side_array_cutoff;
uint8_t right_side_array_cutoff;
}measure_params;
measure_params msr;
uint8_t a_factor = 50; /*CV_ARRAY_FLASH[59];..................*/
uint16_t calc_end_target(){
//Forward
if(target_direction){
if (target_speed_step == 128) return 0;
else return (target_speed_step-129) * a_factor ; /* (float) CV_ARRAY_FLASH[59]*/
}
//Reverse
else {
if (target_speed_step == 0) return 0;
else return (target_speed_step-1) * a_factor; /*(float)CV_ARRAY_FLASH[59]*/
}
}
bool speed_helper() {
uint8_t accel_rate = CV_ARRAY_FLASH[2];
uint8_t decel_rate = CV_ARRAY_FLASH[3];
uint16_t end_target = calc_end_target();
//current_target only gets adjusted when the counter equals the acc/dec rate
//-> Time for 1 Speed Step := (speed_helper timer delay)*(accel_rate)
static uint8_t speed_helper_counter;
//Emergency Stop
if (target_speed_step == 129 || target_speed_step==1) {
current_target = 0;
speed_helper_counter = 0;
}
//Acceleration
else if (end_target > current_target && speed_helper_counter == accel_rate) {
if(!accel_rate) current_target = end_target; // directly accelerate to end target speed
else current_target += a_factor;
speed_helper_counter = 0;
}
//Deceleration
else if (end_target < current_target && speed_helper_counter == decel_rate) {
if(!decel_rate) current_target = end_target; // directly decelerate to end target speed
else current_target -= a_factor;
speed_helper_counter = 0;
}
//Acceleration/Deceleration "scheduled"
else if (end_target != current_target) speed_helper_counter++;
//Target reached -> Reset Counter
else speed_helper_counter = 0;
current_target_voltage = (float)current_target/1260;
return true;
}
float measure(bool direction){
uint32_t sum = 0;
uint16_t adc_val[100];
pwm_set_gpio_level(MOTOR_PWM_FORWARD,0);
pwm_set_gpio_level(MOTOR_PWM_REVERSE,0);
adc_select_input(!direction);
busy_wait_us(msr.delay_in_us);
adc_run(true);
int key, j;
for (int i = 0; i < msr.total_iterations; ++i) {
//Take adc value out of fifo when available, then do one step of insertion sort.
adc_val[i] = adc_fifo_get_blocking();
key = adc_val[i];
j = i - 1;
while (j >= 0 && adc_val[j] > key) {
adc_val[j + 1] = adc_val[j];
j = j - 1;
}
adc_val[j + 1] = key;
}
adc_run(false);
//discard x entries beginning from the lowest entry of the array (counting up); x = msr.left_side_array_cutoff
//discard y entries beginning from the highest index of the array (counting down); y = msr.right_side_array_cutoff
for (uint8_t i = msr.left_side_array_cutoff; i < msr.total_iterations - msr.right_side_array_cutoff ; ++i) {
sum += adc_val[i];
}
//V_z is represented in 12bit
float V_z = (float)sum / (float)(msr.total_iterations - (msr.left_side_array_cutoff+msr.right_side_array_cutoff));
//Zener correction (approximated) & Conversion factor for V_z <= 1951
//Function Returns Value in "Volts"
if (V_z > 1951){
float V_z_sq = V_z * V_z;
return ( C0 + C1 * V_z + C2 * V_z_sq + C3 * V_z * V_z_sq + C4 * V_z_sq * V_z_sq);
}
else return (L1*V_z);
}
void adjust_pwm_level(uint16_t level) {
if (target_direction) {
pwm_set_gpio_level(MOTOR_PWM_REVERSE,0);
pwm_set_gpio_level(MOTOR_PWM_FORWARD,level);
}
//Reverse
else {
pwm_set_gpio_level(MOTOR_PWM_FORWARD,0);
pwm_set_gpio_level(MOTOR_PWM_REVERSE,level);
}
}
void set_pid_params(float v){
float v_max = (float)a_factor/10;
pid.t_s = 5.0f / 1000;
pid.k_p = 200.0f;
pid.k_p = (-200000*current_target_voltage)/v_max+200000.0f;
pid.a_1 = 200.0f * pid.t_s; // k_i*t_s
pid.a_2 = 0.0f / pid.t_s; // k_d/t_s
}
bool pid_control(struct repeating_timer *t){
pid.output += (float)(pid.startup_offset_fwd*target_direction + pid.startup_offset_rev*(!target_direction));
float measured_voltage = measure(target_direction);
if(target_direction != pid.direction_prev) pid.e_sum = 0.0f;
pid.e = current_target_voltage - (measured_voltage - ADC_OFFSET);
pid.e_sum += pid.e;
if (pid.e_sum > pid.sum_limit_max) pid.e_sum = pid.sum_limit_max;
else if (pid.e_sum < pid.sum_limit_min) pid.e_sum = pid.sum_limit_min;
pid.output = (pid.k_p * (float)pid.e) +
(pid.a_1 * (float)pid.e_sum) + // k_i*t_s*e_sum
(pid.a_2 * (float)(pid.e - pid.e_prev)); // (k_d/t_s)*(e-e_prev)
if (pid.output < 0 || current_target == 0) pid.output = 0;
else if (pid.output > 5000) pid.output = 5000;
adjust_pwm_level((uint16_t )pid.output);
adc_fifo_drain();
pid.direction_prev = target_direction;
pid.e_prev = pid.e;
return true;
}
void init_pid(){
msr.total_iterations = 100;/*CV_ARRAY_FLASH[60];*/
msr.delay_in_us = 100; /*CV_ARRAY_FLASH[61];*/
msr.left_side_array_cutoff = 15;/*CV_ARRAY_FLASH[62];*/
msr.right_side_array_cutoff = 15;/*CV_ARRAY_FLASH[63];*/
// pid.k_p = ((float)CV_ARRAY_FLASH[48] / 256);
// pid.t_s = ((float)CV_ARRAY_FLASH[47] / 1000);
// pid.a_1 = ((float)CV_ARRAY_FLASH[49] / 64) * pid.t_s ; // k_i*t_s
// pid.a_2 = ((float)CV_ARRAY_FLASH[50] / 4096) / pid.t_s; // k_d/t_s
//pid.k_p = (-200000*current_target_voltage)/v_max+200000.0f;
pid.k_p = 200.0f;
pid.t_s = (float) CV_ARRAY_FLASH[47] / 1000;
pid.a_1 = 2000.0f * pid.t_s; // k_i*t_s
pid.a_2 = 0.0f / pid.t_s; // k_d/t_s
pid.sum_limit_max = 100.0f;/*(float)(CV_ARRAY_FLASH[51] );*/
pid.sum_limit_min = -100.0f;/*(float)(CV_ARRAY_FLASH[52] * (-1));*/
pid.direction_prev = target_direction;
pid.startup_offset_fwd = (CV_ARRAY_FLASH[53]) + (CV_ARRAY_FLASH[54]<<8);
pid.startup_offset_rev = (CV_ARRAY_FLASH[55]) + (CV_ARRAY_FLASH[56]<<8);
}
void init_pwm_core1(uint gpio) {
uint slice_num = pwm_gpio_to_slice_num(gpio);
uint32_t wrap_counter = 5000; // 5000 Cycles @ 125MHz for 1 Period -> 25kHz
pwm_set_wrap(slice_num, wrap_counter);
pwm_set_gpio_level(gpio,0);
pwm_set_enabled(slice_num, true);
}
void core1_entry() {
printf("core1 init...\n");
if(gpio_get_function(MOTOR_PWM_FORWARD)!=4){
gpio_set_function(MOTOR_PWM_FORWARD, GPIO_FUNC_PWM);
gpio_set_function(MOTOR_PWM_REVERSE, GPIO_FUNC_PWM);
adc_init();
adc_gpio_init(V_EMF_ADC_PIN_FORWARD);
adc_gpio_init(V_EMF_ADC_PIN_REVERSE);
adc_fifo_setup(true,false,0,false,false);
init_pwm_core1(MOTOR_PWM_FORWARD);
init_pwm_core1(MOTOR_PWM_REVERSE);
init_pid();
}
alarm_pool_add_repeating_timer_ms(alarm_pool_create(0,1),
CV_ARRAY_FLASH[47],
pid_control,
NULL,
&pid_control_timer);
irq_set_priority(0,0x00); // 0x00 = highest priority
alarm_pool_add_repeating_timer_ms(alarm_pool_create(1,1),
CV_ARRAY_FLASH[58],
speed_helper,
NULL,
&speed_helper_timer);
printf("core1 done\n");
while (1);
}