added startup offset to establish a baseline duty cycle at which the motor starts to spin

This commit is contained in:
1nct committed 2022-02-20 11:32:03 +01:00
1 parent 1334f9c540
commit cdb68b84da
6 files changed
+251 -196

No files matched your search

+24 -17
View File
@@ -1,16 +1,20 @@
#include "inttypes.h"
#define CV_ARRAY_SIZE 512
//All CVs are 8-bit numbers (range 0 - 255)
//Note : CV_1 ≙ index 0, CV_2 ≙ index 1, CV_3 ≙ index 2, ...
uint8_t CV_ARRAY_DEFAULT [512] = {
//TODO:
// - pwm CV for aux & gpio (duty cycle/freq)
// - Packet Timeout
// - Motor PWM Clock & Divider
// - V_max/V_min & V_emf
// -
uint8_t CV_ARRAY_DEFAULT [CV_ARRAY_SIZE] = {
0b00000011, //CV_1 - Basic Address
0b00000000, //CV_2 - Minimum Speed
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
// 255 == Fastest dec/acc rate; 0 == slowest;
// Note that there is an integer division in play here which will get rid of the fractional part
// this means that a value of 254 for example, will result in the same behaviour as an 248.
// This does not correspond to the norm and might be changed eventually.
0b00000101, //CV_3 - Acceleration Rate
0b00000101, //CV_4 - Deceleration Rate
// 0 == Fastest dec/acc rate; 255 == slowest;
0b00000000, //CV_3 - Acceleration Rate
0b00000000, //CV_4 - Deceleration Rate
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
0b11111111, //CV_5 - V_max
0b01111111, //CV_6 - V_mid
@@ -18,7 +22,7 @@ uint8_t CV_ARRAY_DEFAULT [512] = {
0b00001101, //CV_8 - Manufacturer
0b00000000, //CV_9 - PWM-Period
0b00000001, //CV_10 - PWM Clock Divider
0b11111111, //CV_11 - Packet Timeout in seconds TODO: not implemented yet
0b11111111, //CV_11 - Packet Timeout in seconds
0b00000100, //CV_12 - Permitted operating modes
0b00000000, //CV_13 -
0b00000000, //CV_14 -
@@ -67,14 +71,17 @@ uint8_t CV_ARRAY_DEFAULT [512] = {
0b01111011, //CV_51 - PID Control D_Factor ≙ CV_51/4096 i.e. Default = 123 -> 0.03002 sec //
0b00110000, //CV_52 - PID Integral Limit positive ≙ CV_52*10 i.e. Default = 48 -> +480 //
0b00110000, //CV_53 - PID Integral Limit negative ≙ CV_53*(-10) i.e. Default = 48 -> -480 //
//This Offset is used to establish a "baseline" motor PWM duty cycle at which the motor starts to move
//If CV_54+CV_55+CV_56+CV_57 = 0 (after reset or manual overwrite) there will be a measurement procedure on startup//
//alternatively, the measurement can be done by writing a 7 to CV_7 on the programming track. //
0b00000000, //CV_54 - Forward Direction Offset Bits 0-7 Default = 0 //
0b00000000, //CV_55 - Forward Direction Offset Bits 8-15 Default = 0 //
0b00000000, //CV_56 - Reverse Direction Offset Bits 0-7 Default = 0 //
0b00000000, //CV_57 - Reverse Direction Offset Bits 8-15 Default = 0 //
0b00000110, //CV_58 - Offset Measurement Cycles Default = 6 //
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
0b00000000, //CV_54 -
0b00000000, //CV_55 -
0b00000000, //CV_56 -
0b00000000, //CV_57 -
0b00000000, //CV_58 -
0b00000000, //CV_59 -
0b00010100, //CV_60 - PWM scaling factor (target EMF Voltage) -> 126*CV_60 = end_target|max
0b00000111, //CV_59 - speed_helper timer delay - can be used to adjust accel/decel rate //
0b00010100, //CV_60 - PWM scaling factor (target EMF Voltage) -> 126*CV_60 = end_target|max //
// V_EMF Measurement Configuration //////////////////////////////////////////////////////////////////////////////////
0b01000110, //CV_61 - V_EMF Total amount of Measurement Iterations - Default = 70 iterations //
0b01100100, //CV_62 - V_EMF Delay before Measuring - Default = 100us //
@@ -83,8 +90,8 @@ uint8_t CV_ARRAY_DEFAULT [512] = {
// For Example: CV_63 = x and CV_64 = y //
// -> The x smallest values will be discarded. //
// -> The y largest values will be discarded. //
0b00001111, //CV_63 - left_side_array_cutoff - Default = 15 //
0b00001111, //CV_64 - right_side_array_cutoff - Default = 15 // //
0b00001111, //CV_63 - left_side_array_cutoff - Default = 15 //
0b00001111, //CV_64 - right_side_array_cutoff - Default = 15 // //
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
0b00000000, //CV_65 -
0b00000000, //CV_66 -
+142 -87
View File
@@ -5,63 +5,79 @@
//////////////////////////
#include "core0.h"
bool target_direction = true;
uint target_speed_step = 128;
bool target_direction = true; //Forward = true - Reverse = false
uint target_speed_step = 128; //128 = Stop (Forward Direction)
const uint8_t *CV_ARRAY_FLASH = (const uint8_t *) (XIP_BASE + FLASH_TARGET_OFFSET);
bool active_functions[SIZE_ACTIVE_FUNCTIONS] = {false};
uint64_t last_bits = 0;
bool reset_package_flag = false;
absolute_time_t falling_edge_time,rising_edge_time;
int8_t check_for_package() { //returns number of bytes if valid bit-pattern is found. Otherwise -1 is returned.
uint64_t package3Masked = last_bits & PACKAGE_MASK_3_BYTES;
if (package3Masked == PACKAGE_3_BYTES) {
return 3;
uint find_offset(uint level,uint step,uint delay,float threshold, bool direction){
pwm_set_gpio_level(!direction,0);
uint gpio = MOTOR_PWM_FORWARD*direction + MOTOR_PWM_REVERSE*!direction;
while((measure(direction)-ADC_OFFSET)<threshold){
pwm_set_gpio_level(gpio,level);
busy_wait_ms(delay);
level += step;
}
uint64_t package4Masked = last_bits & PACKAGE_MASK_4_BYTES;
if (package4Masked == PACKAGE_4_BYTES) {
return 4;
}
uint64_t package5Masked = last_bits & PACKAGE_MASK_5_BYTES;
if (package5Masked == PACKAGE_5_BYTES) {
return 5;
}
return -1;
pwm_set_gpio_level(direction,0);
return level;
}
void writeLastBit(bool bit) {
last_bits <<= 1;
last_bits |= bit;
}
int64_t readBit_alarm_callback(alarm_id_t id, void *user_data) {
writeLastBit(!gpio_get(DCC_INPUT_PIN));
evaluation();
return 0;
}
//start of transmission -> byte_n(address byte) -> ... -> byte_0(error detection byte) -> end of transmission
void bits_to_byte_array(int8_t number_of_bytes,uint8_t byte_array[]) {
for (uint8_t i = 0; i < number_of_bytes; i++) {
byte_array[i] = last_bits >> (i * 9 + 1);
uint two_sigma(const uint arr[], uint length){
//Calculate arithmetic average
uint sum = 0;
for (uint i = 0; i < length; ++i) {
sum += arr[i];
}
uint x_avg = sum / length;
//Calculate variance
sum = 0;
for (uint i = 0; i < length; ++i) {
sum += (arr[i]-x_avg)*(arr[i]-x_avg);
}
float variance = (float) sum/ (float)(length-1);
//Calculate standard deviation
uint std_dev = (uint)sqrtf(variance);
//"Filter" every array element that deviates more than 2*(std_dev)
sum = 0;
uint counter = 0;
for (uint i = 0; i < length; ++i) {
uint val = arr[i]-x_avg;
if ( val < 2*std_dev || val > (0-2*std_dev) ){
sum += arr[i];
counter++;
}
}
//Calculate and return "new" arithmetic average
return sum / counter;
}
void adjust_pwm_level(uint16_t level) {
if (target_direction) {
pwm_set_gpio_level(MOTOR_PWM_REVERSE,0);
pwm_set_gpio_level(MOTOR_PWM_FORWARD,level);
}
//Reverse
else {
pwm_set_gpio_level(MOTOR_PWM_FORWARD,0);
pwm_set_gpio_level(MOTOR_PWM_REVERSE,level);
void setup_offsets(uint length){
uint offsets_fwd[length];
uint offsets_rev[length];
for (int i = 0; i < length; ++i) {
offsets_fwd[i] = find_offset(0,1,1,0.05f,true);
busy_wait_ms(500);
offsets_rev[i] = find_offset(0,1,1,0.05f,false);
busy_wait_ms(500);
}
uint offsets_fwd_avg = two_sigma(offsets_fwd, length);
uint offsets_rev_avg = two_sigma(offsets_rev, length);
uint8_t CV_ARRAY_TEMP[CV_ARRAY_SIZE];
memcpy(CV_ARRAY_TEMP, CV_ARRAY_FLASH, sizeof(CV_ARRAY_TEMP));
CV_ARRAY_TEMP[53] = offsets_fwd_avg;
CV_ARRAY_TEMP[54] = offsets_fwd_avg>>8;
CV_ARRAY_TEMP[55] = offsets_rev_avg;
CV_ARRAY_TEMP[56] = offsets_rev_avg>>8;
flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE);
flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_TEMP, FLASH_PAGE_SIZE * 2);
acknowledge();
}
void acknowledge() {
target_direction = false;
adjust_pwm_level(5000);
pwm_set_gpio_level(MOTOR_PWM_FORWARD,5000);
busy_wait_ms(6);
adjust_pwm_level(0);
pwm_set_gpio_level(MOTOR_PWM_FORWARD,0);
}
void verify_cv_bit(uint16_t cv_address,bool bit_val, uint8_t bit_pos) {
uint8_t mask = 0b00000001;
bool res = ( (CV_ARRAY_FLASH[cv_address] >> bit_pos) &mask ) == bit_val;
@@ -74,36 +90,30 @@ void verify_cv_byte(uint16_t cv_address, uint8_t cv_data){
}
void write_cv_byte(uint16_t cv_index, uint8_t cv_data){
//CV_7 & CV_8 are read-only
if (cv_index == 6 || cv_index == 7){
//Reset all CVs to Default (CV_8; Value = 8)
if (cv_data == 8){
flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE);
flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_DEFAULT, FLASH_PAGE_SIZE * 2);
acknowledge();
}
//Reset all CVs to Default (CV_8; Value = 8)
if(cv_index == 7 && cv_data == 8){
flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE);
flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_DEFAULT, FLASH_PAGE_SIZE * 2);
acknowledge();
}
else if(cv_index == 0 && cv_data == 0); //CV_1 = 0 is not permitted
//Re-setup offset Adjustment (CV_7; Value = 7);
else if(cv_index == 6 && cv_data == 7){
setup_offsets(CV_ARRAY_FLASH[57]);
}
//CV_1 = 0 is not permitted
else if(!cv_index && !cv_data);
else{
uint8_t CV_ARRAY_TEMP[512] = {0};
memcpy(CV_ARRAY_TEMP, CV_ARRAY_FLASH, sizeof(CV_ARRAY_TEMP));
CV_ARRAY_TEMP[cv_index] = cv_data;
flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE);
flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_TEMP, FLASH_PAGE_SIZE * 2);
acknowledge();
uint8_t CV_ARRAY_TEMP[CV_ARRAY_SIZE];
memcpy(CV_ARRAY_TEMP, CV_ARRAY_FLASH, sizeof(CV_ARRAY_TEMP));
CV_ARRAY_TEMP[cv_index] = cv_data;
flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE);
flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_TEMP, FLASH_PAGE_SIZE * 2);
acknowledge();
}
}
bool reset_package_check(uint8_t number_of_bytes,const uint8_t byte_array[]){
if (byte_array[number_of_bytes-1] == 0b00000000 && byte_array[number_of_bytes-2] == 0b00000000){
target_speed_step = 1;
//update_active_functions(0,0,37);
return true;
}else {
return false;
}
}
void program_mode(uint8_t number_of_bytes, const uint8_t byte_array[]){
if( !((CV_ARRAY_FLASH[53])+(CV_ARRAY_FLASH[54]<<8)) || !((CV_ARRAY_FLASH[55])+(CV_ARRAY_FLASH[56]<<8)) ){
}
//Check for valid programming command ("address" 112-127)
if (byte_array[number_of_bytes - 1]<128 && byte_array[number_of_bytes - 1]>111){
uint8_t instruction_type_mask = 0b00001100;
@@ -135,7 +145,6 @@ void program_mode(uint8_t number_of_bytes, const uint8_t byte_array[]){
multicore_launch_core1(core1_entry);
}
}
void set_outputs() {
uint32_t GPIO_to_be_set = 0;
for (uint8_t i = 0; i < 32; i++) {
@@ -151,7 +160,6 @@ void set_outputs() {
GPIO_to_be_set &= ALLOWED_GPIO_MASK;
gpio_put_masked(ALLOWED_GPIO_MASK,GPIO_to_be_set);
}
void update_active_functions(uint8_t function_number, uint8_t input_byte, uint8_t count) {
uint8_t mask = 0b00000001;
for (uint8_t i = 0; i < count; i++) {
@@ -159,7 +167,6 @@ void update_active_functions(uint8_t function_number, uint8_t input_byte, uint8_
mask = mask << 1;
}
}
bool error_detection(int8_t number_of_bytes, const uint8_t byte_array[]) {
//Bitwise XOR for all Bytes -> Successful result is: "0000 0000"
uint8_t xor_byte = 0;
@@ -168,13 +175,11 @@ bool error_detection(int8_t number_of_bytes, const uint8_t byte_array[]) {
}
return (0 == xor_byte);
}
// Returns true for long address
bool is_long_address(uint8_t number_of_bytes, const uint8_t byte_array[]) {
if ((byte_array[number_of_bytes - 1]>>6) == 0b00000011) return true;
return false;
}
bool address_evaluation(uint8_t number_of_bytes,const uint8_t byte_array[]) {
//Check for Idle Package
if (byte_array[number_of_bytes - 1] == 255)
@@ -201,7 +206,6 @@ bool address_evaluation(uint8_t number_of_bytes,const uint8_t byte_array[]) {
return (CV_ARRAY_FLASH[0] == read_address);
}
}
void instruction_evaluation(uint8_t number_of_bytes,const uint8_t byte_array[]) {
uint8_t command_byte_n;
uint8_t command_byte_start_index;
@@ -216,10 +220,10 @@ void instruction_evaluation(uint8_t number_of_bytes,const uint8_t byte_array[])
if (command_byte_n == 0b00111111){
target_speed_step = byte_array[command_byte_start_index - 1];
if(target_speed_step>127) {
target_direction = true;
target_direction = true; //Forward
}
else {
target_direction = false;
target_direction = false; //Reverse
}
}
// 10XX-XXXX (Function Group Instruction)
@@ -260,11 +264,40 @@ void instruction_evaluation(uint8_t number_of_bytes,const uint8_t byte_array[])
}
set_outputs();
}
//Interrupt handler for DCC Logic Signal
void gpio_callback_rise(unsigned int gpio, long unsigned int events) {
add_alarm_in_us(87, &readBit_alarm_callback, NULL, false);
bool reset_package_check(uint8_t number_of_bytes,const uint8_t byte_array[]){
if (byte_array[number_of_bytes-1] == 0b00000000 && byte_array[number_of_bytes-2] == 0b00000000){
target_speed_step = 1;
//update_active_functions(0,0,37);
return true;
}else {
return false;
}
}
int8_t check_for_package() { //returns number of bytes if valid bit-pattern is found. Otherwise -1 is returned.
uint64_t package3Masked = last_bits & PACKAGE_MASK_3_BYTES;
if (package3Masked == PACKAGE_3_BYTES) {
return 3;
}
uint64_t package4Masked = last_bits & PACKAGE_MASK_4_BYTES;
if (package4Masked == PACKAGE_4_BYTES) {
return 4;
}
uint64_t package5Masked = last_bits & PACKAGE_MASK_5_BYTES;
if (package5Masked == PACKAGE_5_BYTES) {
return 5;
}
return -1;
}
void writeLastBit(bool bit) {
last_bits <<= 1;
last_bits |= bit;
}
//start of transmission -> byte_n(address byte) -> ... -> byte_0(error detection byte) -> end of transmission
void bits_to_byte_array(int8_t number_of_bytes,uint8_t byte_array[]) {
for (uint8_t i = 0; i < number_of_bytes; i++) {
byte_array[i] = last_bits >> (i * 9 + 1);
}
}
void evaluation(){
int8_t number_of_bytes = check_for_package();
if (number_of_bytes != -1) {
@@ -274,9 +307,9 @@ void evaluation(){
}
if (error_detection(number_of_bytes,byte_array)) {
if (address_evaluation(number_of_bytes,byte_array)) {
reset_package_flag = false;
instruction_evaluation(number_of_bytes,byte_array);
}
reset_package_flag = false;
instruction_evaluation(number_of_bytes,byte_array);
}
else if (reset_package_flag){
program_mode(number_of_bytes,byte_array);
}
@@ -286,7 +319,24 @@ void evaluation(){
}
}
}
void track_signal_rise(unsigned int gpio, long unsigned int events) {
rising_edge_time = get_absolute_time();
gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE, false, &track_signal_rise);
gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_FALL, true, &track_signal_fall);
}
void track_signal_fall(unsigned int gpio, long unsigned int events) {
falling_edge_time = get_absolute_time();
int64_t time_logical_high = absolute_time_diff_us(rising_edge_time,falling_edge_time);
if(time_logical_high > 87){
writeLastBit(0);
}
else{
writeLastBit(1);
}
evaluation();
gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_FALL, false, &track_signal_fall);
gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE, true, &track_signal_rise);
}
int main() {
stdio_init_all();
printf("core0 init...\n");
@@ -295,8 +345,13 @@ int main() {
multicore_launch_core1(core1_entry);
gpio_init(DCC_INPUT_PIN);
gpio_set_dir(DCC_INPUT_PIN, GPIO_IN);
gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE, true, &gpio_callback_rise);
printf("core0 done\n");
while (1){
busy_wait_ms(100);
//Check for offset setup
if( !( (CV_ARRAY_FLASH[53]) + (CV_ARRAY_FLASH[54]<<8) + (CV_ARRAY_FLASH[55]) + (CV_ARRAY_FLASH[56]<<8) ) ){
uint8_t arr[4] = {125,7,6,124};
program_mode(4,arr);
}
gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE, true, &track_signal_rise);
printf("core0 done\n");
while (1);
}
+7 -3
View File
@@ -7,6 +7,7 @@
#pragma once
#include "shared.h"
#include "CV.h"
#include "pico/float.h"
#define SIZE_BYTE_ARRAY 5
#define SIZE_ACTIVE_FUNCTIONS 32
#define DCC_INPUT_PIN 9
@@ -20,7 +21,6 @@
#define PACKAGE_MASK_4_BYTES 0b11111111111000000001000000001000000001000000001
#define PACKAGE_5_BYTES 0b11111111110000000000000000000000000000000000000000000001
#define PACKAGE_MASK_5_BYTES 0b11111111111000000001000000001000000001000000001000000001
#define FLASH_TARGET_OFFSET (PICO_FLASH_SIZE_BYTES-FLASH_SECTOR_SIZE) //This Offset should be far enough away from program data
int8_t check_for_package();
void writeLastBit(bool bit) ;
int64_t readBit_alarm_callback(alarm_id_t id, void *user_data);
@@ -37,5 +37,9 @@ bool error_detection(int8_t number_of_bytes, const uint8_t byte_array[]) ;
bool is_long_address(uint8_t number_of_bytes, const uint8_t byte_array[]) ;
bool address_evaluation(uint8_t number_of_bytes,const uint8_t byte_array[]) ;
void instruction_evaluation(uint8_t number_of_bytes,const uint8_t byte_array[]);
void gpio_callback_rise(unsigned int gpio, long unsigned int events) ;
void evaluation();
void track_signal_rise(unsigned int gpio, long unsigned int events);
void track_signal_fall(unsigned int gpio, long unsigned int events);
void evaluation();
uint find_offset(uint level,uint step,uint delay,float threshold, bool direction);
uint two_sigma(const uint arr[], uint length);
void setup_offsets(uint length);
+68 -83
View File
@@ -21,6 +21,9 @@ typedef struct pid_params{
float e;
float e_prev;
float e_sum;
uint startup_offset_fwd;
uint startup_offset_rev;
bool direction_prev;
}pid_params;
pid_params pid;
@@ -31,7 +34,7 @@ typedef struct measure_params{
uint8_t right_side_array_cutoff;
}measure_params;
measure_params msr;
uint8_t a_factor = 30; /*CV_ARRAY_FLASH[59];..................*/
uint8_t a_factor = 50; /*CV_ARRAY_FLASH[59];..................*/
uint16_t calc_end_target(){
//Forward
@@ -45,11 +48,9 @@ uint16_t calc_end_target(){
else return (target_speed_step-1) * a_factor; /*(float)CV_ARRAY_FLASH[59]*/
}
}
bool speed_helper() {
uint8_t accel_rate = 1; /*CV_ARRAY_FLASH[2];*/
uint8_t decel_rate = 1; /*CV_ARRAY_FLASH[3];*/
uint8_t accel_rate = CV_ARRAY_FLASH[2];
uint8_t decel_rate = CV_ARRAY_FLASH[3];
uint16_t end_target = calc_end_target();
//current_target only gets adjusted when the counter equals the acc/dec rate
//-> Time for 1 Speed Step := (speed_helper timer delay)*(accel_rate)
@@ -61,38 +62,35 @@ bool speed_helper() {
}
//Acceleration
else if (end_target > current_target && speed_helper_counter == accel_rate) {
current_target += a_factor;
if(!accel_rate) current_target = end_target; // directly accelerate to end target speed
else current_target += a_factor;
speed_helper_counter = 0;
}
//Deceleration
else if (end_target < current_target && speed_helper_counter == decel_rate) {
current_target -= a_factor;
if(!decel_rate) current_target = end_target; // directly decelerate to end target speed
else current_target -= a_factor;
speed_helper_counter = 0;
}
//Acceleration/Deceleration "scheduled"
else if (end_target != current_target){
speed_helper_counter++;
}
else if (end_target != current_target) speed_helper_counter++;
//Target reached -> Reset Counter
else{
speed_helper_counter = 0;
}
else speed_helper_counter = 0;
current_target_voltage = (float)current_target/1260;
return true;
}
float measure(){
float measure(bool direction){
uint32_t sum = 0;
uint16_t adc_val[100];
pwm_set_gpio_level(MOTOR_PWM_FORWARD,0);
pwm_set_gpio_level(MOTOR_PWM_REVERSE,0);
adc_select_input(!target_direction);
busy_wait_us(100/*msr.delay_in_us*/);
uint32_t sum = 0;
uint16_t adc_val[100/*msr.total_iterations*/];
adc_select_input(!direction);
busy_wait_us(msr.delay_in_us);
adc_run(true);
int key, j;
for (int i = 0; i < 100/*msr.total_iterations*/; ++i) {
for (int i = 0; i < msr.total_iterations; ++i) {
//Take adc value out of fifo when available, then do one step of insertion sort.
adc_val[i] = adc_fifo_get_blocking();
//Insertion Sort (1 Step)
key = adc_val[i];
j = i - 1;
while (j >= 0 && adc_val[j] > key) {
@@ -102,100 +100,87 @@ float measure(){
adc_val[j + 1] = key;
}
adc_run(false);
for (uint8_t i = msr.left_side_array_cutoff; i < 100/*msr.total_iterations*/ - msr.right_side_array_cutoff ; ++i) {
//discard x entries beginning from the lowest entry of the array (counting up); x = msr.left_side_array_cutoff
//discard y entries beginning from the highest index of the array (counting down); y = msr.right_side_array_cutoff
for (uint8_t i = msr.left_side_array_cutoff; i < msr.total_iterations - msr.right_side_array_cutoff ; ++i) {
sum += adc_val[i];
}
//V_z is represented in 12bit
float V_z = (float)sum / (float)(100/*msr.total_iterations*/ - 30);
float V_z = (float)sum / (float)(msr.total_iterations - (msr.left_side_array_cutoff+msr.right_side_array_cutoff));
//Zener correction (approximated) & Conversion factor for V_z <= 1951
//Returns Value in "Volts"
//Function Returns Value in "Volts"
if (V_z > 1951){
float V_z_sq = V_z * V_z;
return ( C0 + C1 * V_z + C2 * V_z_sq + C3 * V_z * V_z_sq + C4 * V_z_sq * V_z_sq);
}
else{
return (L1*V_z);
else return (L1*V_z);
}
void adjust_pwm_level(uint16_t level) {
if (target_direction) {
pwm_set_gpio_level(MOTOR_PWM_REVERSE,0);
pwm_set_gpio_level(MOTOR_PWM_FORWARD,level);
}
//Reverse
else {
pwm_set_gpio_level(MOTOR_PWM_FORWARD,0);
pwm_set_gpio_level(MOTOR_PWM_REVERSE,level);
}
}
void set_pid_params(float v){
float v_max = (float)a_factor/10;
pid.t_s = 5.0f / 1000;
pid.k_p = (-90*v)/v_max+100.0f;
pid.a_1 = 0.0f * pid.t_s; // k_i*t_s
pid.a_2 = 2.0f / pid.t_s; // k_d/t_s
if (pid.k_p<10)pid.k_p=10;
if (pid.a_2<0)pid.k_p=0;
/*if (v > 0.6f * max_voltage){
pid.k_p = 5.0f;
pid.t_s = 5.0f / 1000;
pid.a_1 = 0.5f * pid.t_s; // k_i*t_s
pid.a_2 = 0.0f / pid.t_s; // k_d/t_s
}
else if(v > 0.2f * max_voltage){
pid.k_p = 30.0f;
pid.t_s = 5.0f / 1000;
pid.a_1 = 0.0f * pid.t_s; // k_i*t_s
pid.a_2 = 5.0f / pid.t_s; // k_d/t_s
}*/
//else{
//}
pid.k_p = 200.0f;
pid.k_p = (-200000*current_target_voltage)/v_max+200000.0f;
pid.a_1 = 200.0f * pid.t_s; // k_i*t_s
pid.a_2 = 0.0f / pid.t_s; // k_d/t_s
}
bool pid_control(struct repeating_timer *t){
float measured_voltage = measure();
set_pid_params(measured_voltage);
pid.e = current_target_voltage - measured_voltage;
pid.e_sum = pid.e_sum + pid.e;
pid.output += (float)(pid.startup_offset_fwd*target_direction + pid.startup_offset_rev*(!target_direction));
float measured_voltage = measure(target_direction);
if(target_direction != pid.direction_prev) pid.e_sum = 0.0f;
pid.e = current_target_voltage - (measured_voltage - ADC_OFFSET);
pid.e_sum += pid.e;
if (pid.e_sum > pid.sum_limit_max) pid.e_sum = pid.sum_limit_max;
else if (pid.e_sum < pid.sum_limit_min) pid.e_sum = pid.sum_limit_min;
pid.output += (pid.k_p * (float)pid.e) +
pid.output = (pid.k_p * (float)pid.e) +
(pid.a_1 * (float)pid.e_sum) + // k_i*t_s*e_sum
(pid.a_2 * (float)(pid.e - pid.e_prev)); // (k_d/t_s)*(e-e_prev)
pid.e_prev = pid.e;
if (current_target == 0) pid.output = 0;
if (pid.output < 0 || current_target == 0) pid.output = 0;
else if (pid.output > 5000) pid.output = 5000;
else if (pid.output < 1000) pid.output = 1000;
adjust_pwm_level((uint16_t )pid.output);
adc_fifo_drain();
pid.direction_prev = target_direction;
pid.e_prev = pid.e;
return true;
}
void init_pid(){
msr.total_iterations = 100;/*CV_ARRAY_FLASH[60];*/
msr.delay_in_us = 100; /*CV_ARRAY_FLASH[61];*/
msr.left_side_array_cutoff = 15;/*CV_ARRAY_FLASH[62];*/
msr.right_side_array_cutoff = 15;/*CV_ARRAY_FLASH[63];*/
// pid.k_p = ((float)CV_ARRAY_FLASH[48] / 256);
// pid.t_s = ((float)CV_ARRAY_FLASH[47] / 1000);
// pid.a_1 = ((float)CV_ARRAY_FLASH[49] / 64) * pid.t_s ; // k_i*t_s
// pid.a_2 = ((float)CV_ARRAY_FLASH[50] / 4096) / pid.t_s; // k_d/t_s
//pid.k_p = 5.0f;
//pid.t_s = 5.0f / 1000;
//pid.a_1 = 0.5f * pid.t_s; // k_i*t_s
//pid.a_2 = 0.0f / pid.t_s; // k_d/t_s
pid.sum_limit_max = 200.0f;/*(float)(CV_ARRAY_FLASH[51] );*/
pid.sum_limit_min = -200.0f;/*(float)(CV_ARRAY_FLASH[52] * (-1));*/
msr.total_iterations = 70;/*CV_ARRAY_FLASH[60];*/
msr.delay_in_us = CV_ARRAY_FLASH[61];
msr.left_side_array_cutoff = 15;/*CV_ARRAY_FLASH[62];*/
msr.right_side_array_cutoff = 15;/*CV_ARRAY_FLASH[63];*/
//pid.k_p = (-200000*current_target_voltage)/v_max+200000.0f;
pid.k_p = 200.0f;
pid.t_s = (float) CV_ARRAY_FLASH[47] / 1000;
pid.a_1 = 2000.0f * pid.t_s; // k_i*t_s
pid.a_2 = 0.0f / pid.t_s; // k_d/t_s
pid.sum_limit_max = 100.0f;/*(float)(CV_ARRAY_FLASH[51] );*/
pid.sum_limit_min = -100.0f;/*(float)(CV_ARRAY_FLASH[52] * (-1));*/
pid.direction_prev = target_direction;
pid.startup_offset_fwd = (CV_ARRAY_FLASH[53]) + (CV_ARRAY_FLASH[54]<<8);
pid.startup_offset_rev = (CV_ARRAY_FLASH[55]) + (CV_ARRAY_FLASH[56]<<8);
}
void init_pwm(uint gpio) {
void init_pwm_core1(uint gpio) {
uint slice_num = pwm_gpio_to_slice_num(gpio);
uint32_t wrap_counter = 5000; // 5000 Cycles @ 125MHz for 1 Period -> 25kHz
pwm_set_wrap(slice_num, wrap_counter);
pwm_set_gpio_level(gpio,0);
pwm_set_clkdiv(slice_num,1);
pwm_set_enabled(slice_num, true);
}
void print_cv_array(const uint8_t *buf, size_t len) {
for (size_t i = 0; i < len; ++i) {
printf("CV_%u: %02x",i+1, buf[i]);
if (i % 4 == 3)
printf("\n");
else
printf(" ");
}
}
void core1_entry() {
printf("core1 init...\n");
if(gpio_get_function(MOTOR_PWM_FORWARD)!=4){
@@ -205,21 +190,21 @@ void core1_entry() {
adc_gpio_init(V_EMF_ADC_PIN_FORWARD);
adc_gpio_init(V_EMF_ADC_PIN_REVERSE);
adc_fifo_setup(true,false,0,false,false);
init_pwm(MOTOR_PWM_FORWARD);
init_pwm(MOTOR_PWM_REVERSE);
init_pwm_core1(MOTOR_PWM_FORWARD);
init_pwm_core1(MOTOR_PWM_REVERSE);
init_pid();
}
alarm_pool_add_repeating_timer_ms(alarm_pool_create(0,1),
5/*CV_ARRAY_FLASH[47]*/,
CV_ARRAY_FLASH[47],
pid_control,
NULL,
&pid_control_timer);
irq_set_priority(0,0x00); // 0x00 = highest priority
alarm_pool_add_repeating_timer_ms(alarm_pool_create(1,1),
7,
CV_ARRAY_FLASH[58],
speed_helper,
NULL,
&speed_helper_timer);
printf("core1 done\n");
while (1);
}
}
+5 -3
View File
@@ -17,9 +17,11 @@
#define C3 -1.000062393830345e-08f
#define C4 1.15408454807169e-12f
void adjust_pwm_level(uint16_t level);
uint16_t calc_end_target();
bool speed_helper();
float measure();
void init_pid();
void init_pwm(uint gpio);
void print_cv_array(const uint8_t *buf, size_t len);
void init_pwm_core1(uint gpio);
bool pid_control(struct repeating_timer *t);
void set_pid_params(float v);
void print_cv_array(const uint8_t *buf, size_t len);
+5 -3
View File
@@ -9,17 +9,19 @@
#include "string.h"
#include "pico/stdlib.h"
#include "pico/multicore.h"
#include "pico/util/queue.h"
#include "hardware/pwm.h"
#include "hardware/adc.h"
#include "hardware/flash.h"
#include "hardware/irq.h"
#include "stdint.h"
#define ADC_OFFSET 0.025f
#define MOTOR_PWM_FORWARD 22
#define MOTOR_PWM_REVERSE 23
#define FLASH_TARGET_OFFSET (PICO_FLASH_SIZE_BYTES-FLASH_SECTOR_SIZE) //This Offset should be far enough away from program data
extern repeating_timer_t pid_control_timer;
extern repeating_timer_t speed_helper_timer;
extern bool target_direction;
extern uint target_speed_step;
extern const uint8_t *CV_ARRAY_FLASH;
void adjust_pwm_level(uint16_t level);
void core1_entry();
void core1_entry();
float measure(bool direction);