////////////////////////// // RP2040-Decoder // // Gabriel Koppenstein // // core1.c // ////////////////////////// #include "core1.h" uint16_t current_target = 0; float current_target_voltage = 0; struct repeating_timer pid_control_timer,speed_helper_timer; typedef struct pid_params{ float k_p; float t_s; float a_1; float a_2; float sum_limit_max; float sum_limit_min; float output; float e; float e_prev; float e_sum; uint startup_offset_fwd; uint startup_offset_rev; bool direction_prev; }pid_params; pid_params pid; typedef struct measure_params{ uint8_t delay_in_us; uint8_t total_iterations; uint8_t left_side_array_cutoff; uint8_t right_side_array_cutoff; }measure_params; measure_params msr; uint8_t a_factor = 50; /*CV_ARRAY_FLASH[59];..................*/ uint16_t calc_end_target(){ //Forward if(target_direction){ if (target_speed_step == 128) return 0; else return (target_speed_step-129) * a_factor ; /* (float) CV_ARRAY_FLASH[59]*/ } //Reverse else { if (target_speed_step == 0) return 0; else return (target_speed_step-1) * a_factor; /*(float)CV_ARRAY_FLASH[59]*/ } } bool speed_helper() { uint8_t accel_rate = CV_ARRAY_FLASH[2]; uint8_t decel_rate = CV_ARRAY_FLASH[3]; uint16_t end_target = calc_end_target(); //current_target only gets adjusted when the counter equals the acc/dec rate //-> Time for 1 Speed Step := (speed_helper timer delay)*(accel_rate) static uint8_t speed_helper_counter; //Emergency Stop if (target_speed_step == 129 || target_speed_step==1) { current_target = 0; speed_helper_counter = 0; } //Acceleration else if (end_target > current_target && speed_helper_counter == accel_rate) { if(!accel_rate) current_target = end_target; // directly accelerate to end target speed else current_target += a_factor; speed_helper_counter = 0; } //Deceleration else if (end_target < current_target && speed_helper_counter == decel_rate) { if(!decel_rate) current_target = end_target; // directly decelerate to end target speed else current_target -= a_factor; speed_helper_counter = 0; } //Acceleration/Deceleration "scheduled" else if (end_target != current_target) speed_helper_counter++; //Target reached -> Reset Counter else speed_helper_counter = 0; current_target_voltage = (float)current_target/1260; return true; } float measure(bool direction){ uint32_t sum = 0; uint16_t adc_val[100]; pwm_set_gpio_level(MOTOR_PWM_FORWARD,0); pwm_set_gpio_level(MOTOR_PWM_REVERSE,0); adc_select_input(!direction); busy_wait_us(msr.delay_in_us); adc_run(true); int key, j; for (int i = 0; i < msr.total_iterations; ++i) { //Take adc value out of fifo when available, then do one step of insertion sort. adc_val[i] = adc_fifo_get_blocking(); key = adc_val[i]; j = i - 1; while (j >= 0 && adc_val[j] > key) { adc_val[j + 1] = adc_val[j]; j = j - 1; } adc_val[j + 1] = key; } adc_run(false); //discard x entries beginning from the lowest entry of the array (counting up); x = msr.left_side_array_cutoff //discard y entries beginning from the highest index of the array (counting down); y = msr.right_side_array_cutoff for (uint8_t i = msr.left_side_array_cutoff; i < msr.total_iterations - msr.right_side_array_cutoff ; ++i) { sum += adc_val[i]; } //V_z is represented in 12bit float V_z = (float)sum / (float)(msr.total_iterations - (msr.left_side_array_cutoff+msr.right_side_array_cutoff)); //Zener correction (approximated) & Conversion factor for V_z <= 1951 //Function Returns Value in "Volts" if (V_z > 1951){ float V_z_sq = V_z * V_z; return ( C0 + C1 * V_z + C2 * V_z_sq + C3 * V_z * V_z_sq + C4 * V_z_sq * V_z_sq); } else return (L1*V_z); } void adjust_pwm_level(uint16_t level) { if (target_direction) { pwm_set_gpio_level(MOTOR_PWM_REVERSE,0); pwm_set_gpio_level(MOTOR_PWM_FORWARD,level); } //Reverse else { pwm_set_gpio_level(MOTOR_PWM_FORWARD,0); pwm_set_gpio_level(MOTOR_PWM_REVERSE,level); } } void set_pid_params(float v){ float v_max = (float)a_factor/10; pid.t_s = 5.0f / 1000; pid.k_p = 200.0f; pid.k_p = (-200000*current_target_voltage)/v_max+200000.0f; pid.a_1 = 200.0f * pid.t_s; // k_i*t_s pid.a_2 = 0.0f / pid.t_s; // k_d/t_s } bool pid_control(struct repeating_timer *t){ pid.output += (float)(pid.startup_offset_fwd*target_direction + pid.startup_offset_rev*(!target_direction)); float measured_voltage = measure(target_direction); if(target_direction != pid.direction_prev) pid.e_sum = 0.0f; pid.e = current_target_voltage - (measured_voltage - ADC_OFFSET); pid.e_sum += pid.e; if (pid.e_sum > pid.sum_limit_max) pid.e_sum = pid.sum_limit_max; else if (pid.e_sum < pid.sum_limit_min) pid.e_sum = pid.sum_limit_min; pid.output = (pid.k_p * (float)pid.e) + (pid.a_1 * (float)pid.e_sum) + // k_i*t_s*e_sum (pid.a_2 * (float)(pid.e - pid.e_prev)); // (k_d/t_s)*(e-e_prev) if (pid.output < 0 || current_target == 0) pid.output = 0; else if (pid.output > 5000) pid.output = 5000; adjust_pwm_level((uint16_t )pid.output); adc_fifo_drain(); pid.direction_prev = target_direction; pid.e_prev = pid.e; return true; } void init_pid(){ msr.total_iterations = 100;/*CV_ARRAY_FLASH[60];*/ msr.delay_in_us = 100; /*CV_ARRAY_FLASH[61];*/ msr.left_side_array_cutoff = 15;/*CV_ARRAY_FLASH[62];*/ msr.right_side_array_cutoff = 15;/*CV_ARRAY_FLASH[63];*/ // pid.k_p = ((float)CV_ARRAY_FLASH[48] / 256); // pid.t_s = ((float)CV_ARRAY_FLASH[47] / 1000); // pid.a_1 = ((float)CV_ARRAY_FLASH[49] / 64) * pid.t_s ; // k_i*t_s // pid.a_2 = ((float)CV_ARRAY_FLASH[50] / 4096) / pid.t_s; // k_d/t_s //pid.k_p = (-200000*current_target_voltage)/v_max+200000.0f; pid.k_p = 200.0f; pid.t_s = (float) CV_ARRAY_FLASH[47] / 1000; pid.a_1 = 2000.0f * pid.t_s; // k_i*t_s pid.a_2 = 0.0f / pid.t_s; // k_d/t_s pid.sum_limit_max = 100.0f;/*(float)(CV_ARRAY_FLASH[51] );*/ pid.sum_limit_min = -100.0f;/*(float)(CV_ARRAY_FLASH[52] * (-1));*/ pid.direction_prev = target_direction; pid.startup_offset_fwd = (CV_ARRAY_FLASH[53]) + (CV_ARRAY_FLASH[54]<<8); pid.startup_offset_rev = (CV_ARRAY_FLASH[55]) + (CV_ARRAY_FLASH[56]<<8); } void init_pwm_core1(uint gpio) { uint slice_num = pwm_gpio_to_slice_num(gpio); uint32_t wrap_counter = 5000; // 5000 Cycles @ 125MHz for 1 Period -> 25kHz pwm_set_wrap(slice_num, wrap_counter); pwm_set_gpio_level(gpio,0); pwm_set_enabled(slice_num, true); } void core1_entry() { printf("core1 init...\n"); if(gpio_get_function(MOTOR_PWM_FORWARD)!=4){ gpio_set_function(MOTOR_PWM_FORWARD, GPIO_FUNC_PWM); gpio_set_function(MOTOR_PWM_REVERSE, GPIO_FUNC_PWM); adc_init(); adc_gpio_init(V_EMF_ADC_PIN_FORWARD); adc_gpio_init(V_EMF_ADC_PIN_REVERSE); adc_fifo_setup(true,false,0,false,false); init_pwm_core1(MOTOR_PWM_FORWARD); init_pwm_core1(MOTOR_PWM_REVERSE); init_pid(); } alarm_pool_add_repeating_timer_ms(alarm_pool_create(0,1), CV_ARRAY_FLASH[47], pid_control, NULL, &pid_control_timer); irq_set_priority(0,0x00); // 0x00 = highest priority alarm_pool_add_repeating_timer_ms(alarm_pool_create(1,1), CV_ARRAY_FLASH[58], speed_helper, NULL, &speed_helper_timer); printf("core1 done\n"); while (1); }