Commit Graph
85 Commits
Author SHA1 Message Date
1nct c8eece795f - Added and updated svg files used in docs
- minor change in speed_table calculation
2022-08-01 21:28:06 +02:00
1nct fd017ea685 - added shared.c file containing functions that can be accessed from both cores
- revised CV programming especially writing
- Core 1 is only started when valid package with correct address is received
- Extended addresses are now correctly verified and implemented
- Base PWM measurement is now done on core0 and checked for automatically in cv_setup_check()
- Moved Motor PWM, GPIO, ADC to core0
- Implemented inverted direction mode (CV_29) according to DCC-Standards
- Limited feed-forward parameters y_2 to max_output/y_1
- k_p gain slopes are now calculated on initialization
- k_p gain parameters are also in pid parameter struct now
- Revised init_pid()
- Implemented Packet timeout check (CV_11)
- 16Bit and 32Bit CVs now always have the highest bytes as the lowest array index to accommodate get_XXbit_CV() functions
2022-08-01 17:20:05 +02:00
1nct f09c4ff136 - Reduced amount of global variables. Many variables are now initialized in main() and core1_entry() respectively and then passed as pointer.
- Updates in speed steps are passed via multicore fifo.
- Pointer to direction variable is also passed from core1 to core0 via multicore fifo
- PID parameter struct definition moved to core1.h
- Implemented variable Proportional gain function
- Implemented function to determine base pwm level
- Minor changes regarding variable names
- Added more comments to roughly describe functionality of functions
2022-07-28 14:33:48 +02:00
1nct 15f67f6c8c Change to Pin assignements in shared.h 2022-07-18 13:33:42 +02:00
Gabriel Koppenstein 1d687b1fd9 Add files via upload 2022-05-27 14:57:08 +02:00
unknown 9e68c5b3ec AUX GPIO are now 24-27, ADC GPIO are now 28 and 29 DCC_IN is now 21 - Board Revision is now "0.3" - Omitted Rev. in Kicad filenames 2022-05-02 20:39:42 +02:00
1nct ad570fba35 - remove m_pwm_offset_adjustment;
- offset now adjusted in pid_control loop;
- pid sampling time depends on speed step;
- speed table implemented & and init function;
2022-03-12 10:23:51 +01:00
1nct 330d42a17e - changes to ADC offset adjustment; - changes to output set function; - cv_setup_check() now waits for core1 to launch also after programming 2022-03-06 01:03:17 +01:00
1nct 65250846f9 - improved PIN_MASK definitions; -implemented adc offset adjustment; - implemented startup checks for: factory flash setting, adc offset adjustment, motor offset adjustment; - implemented adc_offset CVs; - implemented CV_65 as indication for flash factory condition; -fixed core0.h 2022-03-05 14:46:48 +01:00
1nct a6fa9ef249 -updated readme, -modified F0-F31 handling, - implemented pwm for F0-F31 2022-03-05 01:41:40 +01:00
1nct 4f5283521d readme update & docs/png update (PCB Front png) 2022-03-02 09:12:17 +01:00
1nct 47d1543109 -updated docs/png 2022-03-02 08:53:32 +01:00
1nct efa3622e80 -updated docs/png -slight change to f.silkscreen 2022-03-02 08:49:10 +01:00
1nct 9f9b7f74d5 updated svg 2022-03-01 22:02:48 +01:00
1nct 3a8e075f97 small changes to schematic and update to docs/svg 2022-03-01 18:27:33 +01:00
1nct 5211e3f40f small changes to B.Silkscreen and B.Fab 2022-03-01 10:03:46 +01:00
1nct a31b3061fc Finished Board 2022-03-01 00:19:48 +01:00
1nct 2cad01370c - implemented linear approximation for pwm duty cycle offset (feed forward)
- changed pid params and variables in measure() from float to integers
- implemented Motor PWM Frequency CV
- improved acknowledge() function ( 3ms forward / 3ms reverse )
- moved automatic offset setup to speed step evaluation
- removed zener diode correction
- some minor changes regarding naming of constants
2022-02-23 02:15:12 +01:00
1nct cdb68b84da added startup offset to establish a baseline duty cycle at which the motor starts to spin 2022-02-20 11:32:03 +01:00
1nct 1334f9c540 -Added Multiplier to lengthen XOSC startup delay 2022-02-17 00:28:44 +01:00
1nct 4d073dd7f7 - Changes to sorting in measure() function
- Changes to Zener Voltage Correction /  measure now returns value in volts
- Changes to Motor control
- Resistor values changed
- Created BOM
2022-02-16 10:45:30 +01:00
1nct 57af1b67a4 removed 47k resistor 2022-02-07 23:41:35 +01:00
GabrielKoppenstein c6790c6653 Slight changes to schematic & progress on PCB design 2022-02-01 02:00:59 +01:00
GabrielKoppenstein 9d53676da3 Deleted unnecessary Files (KiCad) 2022-01-31 12:19:19 +01:00
GabrielKoppenstein ce0b3b4d18 -changes to gitignore regarding KiCad files
-changes to svg Files & Schematic ( Missing Net (GPIO) @ Input Stage)
2022-01-31 12:12:02 +01:00
GabrielKoppenstein dbe7cf42d1 PCB & svg 2022-01-31 01:42:13 +01:00
GabrielKoppenstein 63fdbed912 PCB and Schematic 2022-01-30 01:37:36 +01:00
GabrielKoppenstein 4fd00bf930 git commit -a 2022-01-29 12:12:46 +01:00
GabrielKoppenstein 08459e2ea8 Changed directories 2022-01-29 11:52:00 +01:00
Gabriel Koppenstein 4c660dd7b6 Rename Block_Diagram.svg to svg/Block_Diagram.svg 2022-01-27 23:15:29 +01:00
Gabriel Koppenstein 10da5e1fb7 Rename Motor_Driver.svg to svg/Motor_Driver.svg 2022-01-27 23:15:06 +01:00
Gabriel Koppenstein f63230a576 Rename Input.svg to svg/Input.svg 2022-01-27 23:14:38 +01:00
Gabriel Koppenstein e6b559248a Rename Auxillary.svg to svg/Auxillary.svg 2022-01-27 23:13:44 +01:00
Gabriel Koppenstein ee4627bf6d Add files via upload 2022-01-27 23:12:42 +01:00
Gabriel Koppenstein 9120c912a7 Update Block_Diagram.svg 2022-01-27 19:49:38 +01:00
Gabriel Koppenstein 684350d6f1 Update Block_Diagram.svg 2022-01-27 18:47:54 +01:00
Gabriel Koppenstein 251556a959 Update Block_Diagram.svg 2022-01-27 18:00:33 +01:00
Gabriel Koppenstein 4323fcb9a9 Update Block_Diagram.svg 2022-01-27 17:43:44 +01:00
Gabriel Koppenstein e0875b8796 Add files via upload 2022-01-27 17:08:02 +01:00
1nct 69f5b63d53 Merge remote-tracking branch 'origin/main' 2022-01-27 01:09:27 +01:00
1nct 594f693b9f - Correction for Zener Diode Voltage
- Changes to Header Files
2022-01-27 01:09:06 +01:00
Gabriel Koppenstein 48bda9d25f Update README.md 2022-01-27 00:25:36 +01:00
1nct ebdc57e90a - divided decoder.c in core0.c & core1.c
- improvements on set_outputs()
2022-01-09 11:30:32 +01:00
GabrielKoppenstein f81cf7fb0b - renamed multicore.c to decoder.c and header files respectively
- several changes to pid_control and speed_helper
- measurements are now being "filtered" (x smallest and y biggest values will be discarded to counteract noisy measurements)
- irq priority for core1 adjusted (pid_control irq now has highest priority)
2022-01-06 20:34:44 +01:00
GabrielKoppenstein 6070af4b10 Deprecated files, not needed anymore 2022-01-04 21:47:38 +01:00
GabrielKoppenstein 54e4c3661d mainly changes in ACK, CV read/write, they should be reliable now (Core1 shutdown during read & write Acknowledge due to conflict of PWM functions) 2022-01-04 21:35:27 +01:00
GabrielKoppenstein a642642285 Merge remote-tracking branch 'origin/main' 2022-01-03 02:33:59 +01:00
GabrielKoppenstein 81c99ce227 fixed acknowledge bit/byte read routine, many small fixes and improvements 2022-01-03 02:33:35 +01:00
GabrielKoppenstein a84ff9d175 Update README.md 2021-11-15 21:16:48 +01:00
GabrielKoppenstein 89e33e2135 Update README.md 2021-11-15 21:16:22 +01:00