added startup offset to establish a baseline duty cycle at which the motor starts to spin
This commit is contained in:
1 parent
1334f9c540
commit
cdb68b84da
6 files changed
+251
-196
No files matched your search
@@ -21,6 +21,9 @@ typedef struct pid_params{
|
||||
float e;
|
||||
float e_prev;
|
||||
float e_sum;
|
||||
uint startup_offset_fwd;
|
||||
uint startup_offset_rev;
|
||||
bool direction_prev;
|
||||
}pid_params;
|
||||
pid_params pid;
|
||||
|
||||
@@ -31,7 +34,7 @@ typedef struct measure_params{
|
||||
uint8_t right_side_array_cutoff;
|
||||
}measure_params;
|
||||
measure_params msr;
|
||||
uint8_t a_factor = 30; /*CV_ARRAY_FLASH[59];..................*/
|
||||
uint8_t a_factor = 50; /*CV_ARRAY_FLASH[59];..................*/
|
||||
|
||||
uint16_t calc_end_target(){
|
||||
//Forward
|
||||
@@ -45,11 +48,9 @@ uint16_t calc_end_target(){
|
||||
else return (target_speed_step-1) * a_factor; /*(float)CV_ARRAY_FLASH[59]*/
|
||||
}
|
||||
}
|
||||
|
||||
|
||||
bool speed_helper() {
|
||||
uint8_t accel_rate = 1; /*CV_ARRAY_FLASH[2];*/
|
||||
uint8_t decel_rate = 1; /*CV_ARRAY_FLASH[3];*/
|
||||
uint8_t accel_rate = CV_ARRAY_FLASH[2];
|
||||
uint8_t decel_rate = CV_ARRAY_FLASH[3];
|
||||
uint16_t end_target = calc_end_target();
|
||||
//current_target only gets adjusted when the counter equals the acc/dec rate
|
||||
//-> Time for 1 Speed Step := (speed_helper timer delay)*(accel_rate)
|
||||
@@ -61,38 +62,35 @@ bool speed_helper() {
|
||||
}
|
||||
//Acceleration
|
||||
else if (end_target > current_target && speed_helper_counter == accel_rate) {
|
||||
current_target += a_factor;
|
||||
if(!accel_rate) current_target = end_target; // directly accelerate to end target speed
|
||||
else current_target += a_factor;
|
||||
speed_helper_counter = 0;
|
||||
}
|
||||
//Deceleration
|
||||
else if (end_target < current_target && speed_helper_counter == decel_rate) {
|
||||
current_target -= a_factor;
|
||||
if(!decel_rate) current_target = end_target; // directly decelerate to end target speed
|
||||
else current_target -= a_factor;
|
||||
speed_helper_counter = 0;
|
||||
}
|
||||
//Acceleration/Deceleration "scheduled"
|
||||
else if (end_target != current_target){
|
||||
speed_helper_counter++;
|
||||
}
|
||||
else if (end_target != current_target) speed_helper_counter++;
|
||||
//Target reached -> Reset Counter
|
||||
else{
|
||||
speed_helper_counter = 0;
|
||||
}
|
||||
else speed_helper_counter = 0;
|
||||
current_target_voltage = (float)current_target/1260;
|
||||
return true;
|
||||
}
|
||||
|
||||
float measure(){
|
||||
float measure(bool direction){
|
||||
uint32_t sum = 0;
|
||||
uint16_t adc_val[100];
|
||||
pwm_set_gpio_level(MOTOR_PWM_FORWARD,0);
|
||||
pwm_set_gpio_level(MOTOR_PWM_REVERSE,0);
|
||||
adc_select_input(!target_direction);
|
||||
busy_wait_us(100/*msr.delay_in_us*/);
|
||||
uint32_t sum = 0;
|
||||
uint16_t adc_val[100/*msr.total_iterations*/];
|
||||
adc_select_input(!direction);
|
||||
busy_wait_us(msr.delay_in_us);
|
||||
adc_run(true);
|
||||
int key, j;
|
||||
for (int i = 0; i < 100/*msr.total_iterations*/; ++i) {
|
||||
for (int i = 0; i < msr.total_iterations; ++i) {
|
||||
//Take adc value out of fifo when available, then do one step of insertion sort.
|
||||
adc_val[i] = adc_fifo_get_blocking();
|
||||
//Insertion Sort (1 Step)
|
||||
key = adc_val[i];
|
||||
j = i - 1;
|
||||
while (j >= 0 && adc_val[j] > key) {
|
||||
@@ -102,100 +100,87 @@ float measure(){
|
||||
adc_val[j + 1] = key;
|
||||
}
|
||||
adc_run(false);
|
||||
for (uint8_t i = msr.left_side_array_cutoff; i < 100/*msr.total_iterations*/ - msr.right_side_array_cutoff ; ++i) {
|
||||
//discard x entries beginning from the lowest entry of the array (counting up); x = msr.left_side_array_cutoff
|
||||
//discard y entries beginning from the highest index of the array (counting down); y = msr.right_side_array_cutoff
|
||||
for (uint8_t i = msr.left_side_array_cutoff; i < msr.total_iterations - msr.right_side_array_cutoff ; ++i) {
|
||||
sum += adc_val[i];
|
||||
}
|
||||
//V_z is represented in 12bit
|
||||
float V_z = (float)sum / (float)(100/*msr.total_iterations*/ - 30);
|
||||
float V_z = (float)sum / (float)(msr.total_iterations - (msr.left_side_array_cutoff+msr.right_side_array_cutoff));
|
||||
//Zener correction (approximated) & Conversion factor for V_z <= 1951
|
||||
//Returns Value in "Volts"
|
||||
//Function Returns Value in "Volts"
|
||||
if (V_z > 1951){
|
||||
float V_z_sq = V_z * V_z;
|
||||
return ( C0 + C1 * V_z + C2 * V_z_sq + C3 * V_z * V_z_sq + C4 * V_z_sq * V_z_sq);
|
||||
}
|
||||
else{
|
||||
return (L1*V_z);
|
||||
else return (L1*V_z);
|
||||
}
|
||||
void adjust_pwm_level(uint16_t level) {
|
||||
if (target_direction) {
|
||||
pwm_set_gpio_level(MOTOR_PWM_REVERSE,0);
|
||||
pwm_set_gpio_level(MOTOR_PWM_FORWARD,level);
|
||||
}
|
||||
//Reverse
|
||||
else {
|
||||
pwm_set_gpio_level(MOTOR_PWM_FORWARD,0);
|
||||
pwm_set_gpio_level(MOTOR_PWM_REVERSE,level);
|
||||
}
|
||||
}
|
||||
void set_pid_params(float v){
|
||||
float v_max = (float)a_factor/10;
|
||||
pid.t_s = 5.0f / 1000;
|
||||
pid.k_p = (-90*v)/v_max+100.0f;
|
||||
pid.a_1 = 0.0f * pid.t_s; // k_i*t_s
|
||||
pid.a_2 = 2.0f / pid.t_s; // k_d/t_s
|
||||
if (pid.k_p<10)pid.k_p=10;
|
||||
if (pid.a_2<0)pid.k_p=0;
|
||||
/*if (v > 0.6f * max_voltage){
|
||||
pid.k_p = 5.0f;
|
||||
pid.t_s = 5.0f / 1000;
|
||||
pid.a_1 = 0.5f * pid.t_s; // k_i*t_s
|
||||
pid.a_2 = 0.0f / pid.t_s; // k_d/t_s
|
||||
}
|
||||
else if(v > 0.2f * max_voltage){
|
||||
pid.k_p = 30.0f;
|
||||
pid.t_s = 5.0f / 1000;
|
||||
pid.a_1 = 0.0f * pid.t_s; // k_i*t_s
|
||||
pid.a_2 = 5.0f / pid.t_s; // k_d/t_s
|
||||
}*/
|
||||
//else{
|
||||
|
||||
//}
|
||||
pid.k_p = 200.0f;
|
||||
pid.k_p = (-200000*current_target_voltage)/v_max+200000.0f;
|
||||
pid.a_1 = 200.0f * pid.t_s; // k_i*t_s
|
||||
pid.a_2 = 0.0f / pid.t_s; // k_d/t_s
|
||||
}
|
||||
|
||||
bool pid_control(struct repeating_timer *t){
|
||||
float measured_voltage = measure();
|
||||
set_pid_params(measured_voltage);
|
||||
pid.e = current_target_voltage - measured_voltage;
|
||||
pid.e_sum = pid.e_sum + pid.e;
|
||||
pid.output += (float)(pid.startup_offset_fwd*target_direction + pid.startup_offset_rev*(!target_direction));
|
||||
float measured_voltage = measure(target_direction);
|
||||
if(target_direction != pid.direction_prev) pid.e_sum = 0.0f;
|
||||
pid.e = current_target_voltage - (measured_voltage - ADC_OFFSET);
|
||||
pid.e_sum += pid.e;
|
||||
if (pid.e_sum > pid.sum_limit_max) pid.e_sum = pid.sum_limit_max;
|
||||
else if (pid.e_sum < pid.sum_limit_min) pid.e_sum = pid.sum_limit_min;
|
||||
pid.output += (pid.k_p * (float)pid.e) +
|
||||
pid.output = (pid.k_p * (float)pid.e) +
|
||||
(pid.a_1 * (float)pid.e_sum) + // k_i*t_s*e_sum
|
||||
(pid.a_2 * (float)(pid.e - pid.e_prev)); // (k_d/t_s)*(e-e_prev)
|
||||
pid.e_prev = pid.e;
|
||||
if (current_target == 0) pid.output = 0;
|
||||
if (pid.output < 0 || current_target == 0) pid.output = 0;
|
||||
else if (pid.output > 5000) pid.output = 5000;
|
||||
else if (pid.output < 1000) pid.output = 1000;
|
||||
adjust_pwm_level((uint16_t )pid.output);
|
||||
adc_fifo_drain();
|
||||
pid.direction_prev = target_direction;
|
||||
pid.e_prev = pid.e;
|
||||
return true;
|
||||
}
|
||||
|
||||
void init_pid(){
|
||||
msr.total_iterations = 100;/*CV_ARRAY_FLASH[60];*/
|
||||
msr.delay_in_us = 100; /*CV_ARRAY_FLASH[61];*/
|
||||
msr.left_side_array_cutoff = 15;/*CV_ARRAY_FLASH[62];*/
|
||||
msr.right_side_array_cutoff = 15;/*CV_ARRAY_FLASH[63];*/
|
||||
// pid.k_p = ((float)CV_ARRAY_FLASH[48] / 256);
|
||||
// pid.t_s = ((float)CV_ARRAY_FLASH[47] / 1000);
|
||||
// pid.a_1 = ((float)CV_ARRAY_FLASH[49] / 64) * pid.t_s ; // k_i*t_s
|
||||
// pid.a_2 = ((float)CV_ARRAY_FLASH[50] / 4096) / pid.t_s; // k_d/t_s
|
||||
//pid.k_p = 5.0f;
|
||||
//pid.t_s = 5.0f / 1000;
|
||||
//pid.a_1 = 0.5f * pid.t_s; // k_i*t_s
|
||||
//pid.a_2 = 0.0f / pid.t_s; // k_d/t_s
|
||||
pid.sum_limit_max = 200.0f;/*(float)(CV_ARRAY_FLASH[51] );*/
|
||||
pid.sum_limit_min = -200.0f;/*(float)(CV_ARRAY_FLASH[52] * (-1));*/
|
||||
msr.total_iterations = 70;/*CV_ARRAY_FLASH[60];*/
|
||||
msr.delay_in_us = CV_ARRAY_FLASH[61];
|
||||
msr.left_side_array_cutoff = 15;/*CV_ARRAY_FLASH[62];*/
|
||||
msr.right_side_array_cutoff = 15;/*CV_ARRAY_FLASH[63];*/
|
||||
//pid.k_p = (-200000*current_target_voltage)/v_max+200000.0f;
|
||||
pid.k_p = 200.0f;
|
||||
pid.t_s = (float) CV_ARRAY_FLASH[47] / 1000;
|
||||
pid.a_1 = 2000.0f * pid.t_s; // k_i*t_s
|
||||
pid.a_2 = 0.0f / pid.t_s; // k_d/t_s
|
||||
pid.sum_limit_max = 100.0f;/*(float)(CV_ARRAY_FLASH[51] );*/
|
||||
pid.sum_limit_min = -100.0f;/*(float)(CV_ARRAY_FLASH[52] * (-1));*/
|
||||
pid.direction_prev = target_direction;
|
||||
pid.startup_offset_fwd = (CV_ARRAY_FLASH[53]) + (CV_ARRAY_FLASH[54]<<8);
|
||||
pid.startup_offset_rev = (CV_ARRAY_FLASH[55]) + (CV_ARRAY_FLASH[56]<<8);
|
||||
}
|
||||
|
||||
void init_pwm(uint gpio) {
|
||||
void init_pwm_core1(uint gpio) {
|
||||
uint slice_num = pwm_gpio_to_slice_num(gpio);
|
||||
uint32_t wrap_counter = 5000; // 5000 Cycles @ 125MHz for 1 Period -> 25kHz
|
||||
pwm_set_wrap(slice_num, wrap_counter);
|
||||
pwm_set_gpio_level(gpio,0);
|
||||
pwm_set_clkdiv(slice_num,1);
|
||||
pwm_set_enabled(slice_num, true);
|
||||
}
|
||||
|
||||
void print_cv_array(const uint8_t *buf, size_t len) {
|
||||
for (size_t i = 0; i < len; ++i) {
|
||||
printf("CV_%u: %02x",i+1, buf[i]);
|
||||
if (i % 4 == 3)
|
||||
printf("\n");
|
||||
else
|
||||
printf(" ");
|
||||
}
|
||||
}
|
||||
void core1_entry() {
|
||||
printf("core1 init...\n");
|
||||
if(gpio_get_function(MOTOR_PWM_FORWARD)!=4){
|
||||
@@ -205,21 +190,21 @@ void core1_entry() {
|
||||
adc_gpio_init(V_EMF_ADC_PIN_FORWARD);
|
||||
adc_gpio_init(V_EMF_ADC_PIN_REVERSE);
|
||||
adc_fifo_setup(true,false,0,false,false);
|
||||
init_pwm(MOTOR_PWM_FORWARD);
|
||||
init_pwm(MOTOR_PWM_REVERSE);
|
||||
init_pwm_core1(MOTOR_PWM_FORWARD);
|
||||
init_pwm_core1(MOTOR_PWM_REVERSE);
|
||||
init_pid();
|
||||
}
|
||||
alarm_pool_add_repeating_timer_ms(alarm_pool_create(0,1),
|
||||
5/*CV_ARRAY_FLASH[47]*/,
|
||||
CV_ARRAY_FLASH[47],
|
||||
pid_control,
|
||||
NULL,
|
||||
&pid_control_timer);
|
||||
irq_set_priority(0,0x00); // 0x00 = highest priority
|
||||
alarm_pool_add_repeating_timer_ms(alarm_pool_create(1,1),
|
||||
7,
|
||||
CV_ARRAY_FLASH[58],
|
||||
speed_helper,
|
||||
NULL,
|
||||
&speed_helper_timer);
|
||||
printf("core1 done\n");
|
||||
while (1);
|
||||
}
|
||||
}
|
||||
Reference in new issue
Block a user