Commit Graph
18 Commits
Author SHA1 Message Date
Nemanja Nedeljkovic 23d57af8bd lf em 4x05 chk: add EM4305 anti-clone card password to default dictionary
Adds A1856618 to t55xx_default_pwds. This is the verified working login
password (as used with -p); the bit-reversed on-air form 1866A185 does not
authenticate.
2026-09-28 21:26:56 +02:00
Nemanja Nedeljkovic f71bc53d0c fix(pm5): power on the FPGA in hw fpga config
`hw fpga config` drives the FPGA over JTAG, but on PM5 the FPGA has to be
clocked/powered first - previously that only happened as a side effect of a
reader command (e.g. `hf 14a read`), so `hw fpga config` failed if run on its
own. Bring the FPGA up in the HAL at the start of FpgaStartConfig()
(FpgaSetup24MHzClk) so the command works standalone; no doc workaround needed.
2026-08-20 15:36:17 +02:00
Nemanja Nedeljkovic 6507b8f36b feat(pm5): hf tune --rgb / lf tune --rgb - antenna RGB as a tuning meter
Adds an opt-in `--rgb` flag to the continuous `hf tune` / `lf tune` commands that
mirrors the antenna tuning level on the PM5 antenna RGB LED: blue = low, green =
mid, red = high, tracking the on-screen bar so you can find coupling (e.g. an
implant) by feel without watching the screen.

The colour is computed client-side from the same per-iteration voltage / running
peak the bar uses (so it matches the bar and auto-scales), and pushed to the
device via a new dumb CMD_PM5_RGB_SET {r,g,b}. That command is handled (#ifdef
PM5) by a dedicated AT32 RGB HAL module, common_arm/rgb/{rgb_apis.h,
rgb_hw_at32.c} (RgbLedSet(), I2C controller @ 0x48), wired into the armsrc
Makefile/CMake as SRC_RGB for PM5 only - so no other platform is affected and no
hardware code lands in shared files.
2026-08-20 11:55:55 +02:00
Nemanja Nedeljkovic ba315d8d58 fix(pm5): suppress bogus [FPGA] version section on PM5
PM5's FPGA (Gowin GW1NR) bitstream is loaded at runtime via `hw fpga config`
and is not compiled into the firmware; only the Xilinx fpga_pm3_hf.bit is pulled
in (to generate g_fpga_version_information[]) which PM5 never runs. So the
`[ FPGA ] fpga_pm3_hf.ncd image 2s30vq100` line described a bitstream unrelated
to the actual device.

- Firmware (appmain.c): omit the [FPGA] section from the version string on PM5
  (#ifndef PM5), since there's no meaningful built-in FPGA version to report.
- Client (cmdhw.c): skip the FPGA_TYPE "chip mismatch" check for PM5, which would
  otherwise trigger now that the section is gone.
2026-08-20 10:36:09 +02:00
Nemanja Nedeljkovic 36027b48e6 fix(pm5): report PM5 in hw status [Model] firmware line
The [Model] section only distinguished RDV4 firmware from a "PM3 GENERIC"
else branch, so PM5 (AT32) fell through and printed "Firmware... PM3 GENERIC"
even though the banner/Target/MCU already report PM5/AT32F437. Add an IfPm5()
branch that prints "Firmware... PM5" and the external-flash status.

Note: the "[ FPGA ] ... 2s30vq100" line in hw version is separate and comes
from the firmware-generated version string (fpga_version_info.c). On PM5 the
build reuses the Xilinx fpga_pm3_hf.bit only to generate that version info
(see Makefile.hal PM5 TODO), while the real Gowin FPGA is loaded via JTAG, so
the reported bitstream name is a placeholder. Fixing that is a firmware/build
change, not addressed here.
2026-08-20 10:36:09 +02:00
Nemanja Nedeljkovic 6da7c77427 feat(pm5): report AT32 MCU, flash size and PM5 target in hw version/status
`hw version` and `hw status` decoded the reported chip id as an Atmel AT91
CIDR. On PM5 (AT32) the id is an ARM DBGMCU IDCODE, so it showed
"MCU Unknown", a bogus flash size (32 KB / 973% used) and "PM3 GENERIC".

- Client: when IfPm5(), print MCU "AT32F437" and the real flash size, and add
  a "PM5" target line, instead of running the AT91 decode.
- Firmware: the flash size can't be derived from the AT32 IDCODE, so the device
  now sends GetChipFlashSize(). It is appended AFTER the version string in the
  CMD_VERSION reply, so the wire layout is unchanged and it stays compatible in
  both directions (old client ignores the trailing bytes; new client length-
  guards and treats a missing value as 0). GetChipFlashSize() already exists for
  both AT91 and AT32.
2026-08-19 21:49:43 +02:00
Nemanja Nedeljkovic b81966c419 fix(pm5): select an ERTC clock before the BPR write
The AT32 battery-domain helper at32_bpr_write_dt1() enabled the ERTC (ertcen)
but never selected an ERTC clock source (ertcsel stayed NOCLK). Writing the
ERTC write-protection register (ERTC->wp) requires the ERTC to be clocked, so
with no source the write stalled the APB once the CPU ran at the full PLL clock
(288MHz, 144MHz APB); it only survived on the slow HICK clock.

The bootrom reaches this via check_goto_flash_mode() -> system_bpr_chk_clear()
while reading/clearing the "enter flash mode" magic the OS sets on a software
reset. That runs after ConfigSystemClocks() (the button branch needs
SpinDelayUs()/the timer clock, so the clock must be up first), i.e. at 288MHz,
so the bootrom hung and the device never re-enumerated into the bootloader
until a physical USB replug.

Fix: select the ERTC clock (HEXT/20, as the tick HAL does) before touching the
ERTC registers. HEXT is running by the time this executes, so the wp write no
longer stalls. The fix is contained in the AT32 HAL (sys_hw_at32.c, which only
builds for AT32/PM5); the shared bootrom flow and its ConfigSystemClocks()-first
ordering (needed by AT91/RDV4 SpinDelayUs) are unchanged.
2026-08-19 19:33:01 +02:00
Nemanja Nedeljkovic de89cbb7b0 Changelog and credits 2024-09-22 02:32:45 +02:00
Nemanja Nedeljkovic dd9d9d8f9e Patch for hardnested attack, for avx512f, by @xianglin1998 2024-09-22 02:30:49 +02:00
Nemanja Nedeljkovic 86f0f2cc75 cleanup 2022-07-05 18:12:49 +02:00
nemanjan00 1216c32f3c Changelog 2022-07-05 16:54:56 +02:00
nemanjan00 187d10060b Bootloader mode 2022-07-05 16:44:11 +02:00
nemanjan00 0d41ed0bba --reboot-to-bootloader 2022-07-05 16:15:05 +02:00
Nemanja Nedeljković 9aee8e9cc7 Add tools/mfd_aes_brute/mfd_multi_brute to .gitignore 2022-03-22 01:48:17 +01:00
nemanjan00 5c9693529c Get output with UID 2022-03-22 00:55:37 +01:00
nemanjan00 24d3094012 Check cmd size 2022-03-21 21:34:38 +01:00
nemanjan00 e4c641b708 Add first and last block for READ_MULTI_BLOCK 2022-03-07 02:09:36 +01:00
Nemanja Nedeljković adb207268d Change in hf 15 raw broke support hf_15_magic.lua
There was a change in `hf 15 raw` and this script was not updated to support that change
2021-06-29 12:52:35 +02:00