Commit Graph
25 Commits
Author SHA1 Message Date
Andreas Dröscher 9ba20b590a change: reduced demodulator to bare minimum
The initial code added complexity without improving reading distance.
Thankfully the peak detection signal path has a low noise floor.
2018-08-12 12:51:45 +02:00
Andreas Dröscher 0d0b651246 change: re-added trace log 2018-08-12 12:51:45 +02:00
Andreas Dröscher ff5b046903 change: re-added status LEDs
- LED_A: FPGA and 13.56MHz carrier is active
- LED_B: Reading Byte
- LED_C: Writing Byte
2018-08-12 12:41:45 +02:00
Andreas Dröscher e052fbc433 change: re-added legic write support 2018-08-12 12:41:45 +02:00
Andreas Dröscher 9d330dde87 fix: 32bit tick timer based on TC0 and TC1
TC1 counts the number of TC0 overflows (carry bits).
In random conditions TC1 would return or stay at zero,
instead of counting up. This due to the behavior of the
reset signal.

SAM7S Series Datasheet, 33.5.6 Trigger:
Regardless of the trigger used, it will be taken into account
at the following active edge of the selected clock. This means
that the counter value can be read differently from zero just
after a trigger, especially when a low frequency signal is
selected as the clock.

The new code first prepares TC1 and asserts TC1 trigger and
then prepares TC0 and asserts TC0 trigger. The TC0 start-up
will reset TC1.
2018-08-12 12:41:11 +02:00
Andreas Dröscher c06f0af7f3 change: switched from timestamps (us) to ticks
GetCountUS() has a jitter of +/- 7us this is not precise
enough to keep the PRNG in sync. 1.5 * GET_TICKS on the
other hand is spot on.
2018-08-12 09:59:48 +02:00
Andreas Dröscher e0adc976e0 change: added rx/tx coordination timestamp 2018-08-12 09:59:48 +02:00
Andreas Dröscher 7244f5825d change: legic reader tx back to bigbang
I've tried to modulate the Legic specific pause-puls using ssc and the default
ssc clock of 105.4 kHz (bit periode of 9.4us) - previous commit. However,
the timing was not precise enough. By increasing the ssc clock this could
be circumvented, but the adventage over bitbang would be little.
2018-08-12 09:59:48 +02:00
Andreas Dröscher 3029223158 change: legic reader now uses xcorrelation and ssc based io
- Even tough legic tags transmit just AM using xcorrelation
   results in a significantly better signal quality.
 - Switching from bit bang to a hardware based ssc frees
   up CPU time for other tasks e.g. demodulation
2018-08-12 09:59:48 +02:00
Andreas Dröscher c59150657c add: xcorr 211.875 kHz option
The FPGA supported this frequency for a long time, just the ARM code
had no define to enable it.
2018-08-12 09:59:48 +02:00
Andreas Dröscher bf123082e8 change: remove jerry-riged hysteresis based receiver from hi_read_tx
This future got obsolete by a x-correlation based receiver.

This reverts commit 24fe4dffb4.
2018-08-12 09:59:48 +02:00
Andreas Dröscher db70ab8f7d change: remove broken legic simulator
It will be rewritten in a later commit
2018-08-12 09:59:48 +02:00
Andreas Dröscher 8a53137ab0 change: remove dead legic code
This code was either disabled or never reached.
2018-08-12 09:59:48 +02:00
Andreas Dröscher e779f06c5e change: clean up Legic interface
I see no adventage in poluting all sources that include legicrf.h
with our internal depedencies (includes) and function names.
2018-08-12 09:59:48 +02:00
Andreas Dröscher 83a4259ddc change: fixed xcorrelation for strong signal
The initial code assumed phase shift modulation only. Lately,
xcorrelation is also used for load modulation. But the initial
the assumption that 11 bits are enough isn't true for load
modulation.

This change extends the registers by 2 bits and compresses the
uper bits to preserve the sensitivity on the lower end.
2018-08-10 02:36:04 +02:00
Andreas Dröscher 058426fa17 change: added rx/tx coordination timestamp 2018-08-05 00:57:20 +02:00
Andreas Dröscher 8f797d1388 change: legic reader tx back to bigbang
I've tried to modulate the Legic specific pause-puls using ssc and the default
ssc clock of 105.4 kHz (bit periode of 9.4us) - previous commit. However,
the timing was not precise enough. By increasing the ssc clock this could
be circumvented, but the adventage over bitbang would be little.
2018-08-05 00:57:20 +02:00
Andreas Dröscher 78d5188922 change: legic reader now uses xcorrelation and ssc based io
- Even tough legic tags transmit just AM using xcorrelation
   results in a significantly better signal quality.
 - Switching from bit bang to a hardware based ssc frees
   up CPU time for other tasks e.g. demodulation
2018-08-04 23:13:17 +02:00
Andreas Dröscher d7c57dbc08 add: xcorr 211.875 kHz option
The FPGA supported this frequency for a long time, just the ARM code
had no define to enable it.
2018-08-04 23:13:17 +02:00
Andreas Dröscher 7517c894d2 change: remove jerry-riged hysteresis based receiver from hi_read_tx
This future got obsolete by a x-correlation based receiver.

This reverts commit 24fe4dffb4.
2018-08-04 23:13:17 +02:00
Andreas Dröscher 1adff322b1 change: remove broken legic simulator
It will be rewritten in a later commit
2018-08-04 23:13:17 +02:00
Andreas Dröscher 33eb2f5fa0 change: remove dead legic code
This code was either disabled or never reached.
2018-08-04 23:13:17 +02:00
Andreas Dröscher 37867fbf3b change: clean up Legic interface
I see no adventage in poluting all sources that include legicrf.h
with our internal depedencies (includes) and function names.
2018-08-04 23:13:17 +02:00
Andreas Dröscher 266cfa4442 chg: cleaned up documentation 2018-07-22 16:56:45 +02:00
Andreas Dröscher 6e8775540e fix: GetFromDevice with BIG_BUF_EML
dl_it was expecting CMD_DOWNLOADED_RAW_ADC_SAMPLES_125K
but got CMD_DOWNLOADED_EML_BIGBUF resulting in an upload
silently failing.
2018-07-22 16:56:35 +02:00