Adds an opt-in `--rgb` flag to the continuous `hf tune` / `lf tune` commands that
mirrors the antenna tuning level on the PM5 antenna RGB LED: blue = low, green =
mid, red = high, tracking the on-screen bar so you can find coupling (e.g. an
implant) by feel without watching the screen.
The colour is computed client-side from the same per-iteration voltage / running
peak the bar uses (so it matches the bar and auto-scales), and pushed to the
device via a new dumb CMD_PM5_RGB_SET {r,g,b}. That command is handled (#ifdef
PM5) by a dedicated AT32 RGB HAL module, common_arm/rgb/{rgb_apis.h,
rgb_hw_at32.c} (RgbLedSet(), I2C controller @ 0x48), wired into the armsrc
Makefile/CMake as SRC_RGB for PM5 only - so no other platform is affected and no
hardware code lands in shared files.
PM5's FPGA (Gowin GW1NR) bitstream is loaded at runtime via `hw fpga config`
and is not compiled into the firmware; only the Xilinx fpga_pm3_hf.bit is pulled
in (to generate g_fpga_version_information[]) which PM5 never runs. So the
`[ FPGA ] fpga_pm3_hf.ncd image 2s30vq100` line described a bitstream unrelated
to the actual device.
- Firmware (appmain.c): omit the [FPGA] section from the version string on PM5
(#ifndef PM5), since there's no meaningful built-in FPGA version to report.
- Client (cmdhw.c): skip the FPGA_TYPE "chip mismatch" check for PM5, which would
otherwise trigger now that the section is gone.
The [Model] section only distinguished RDV4 firmware from a "PM3 GENERIC"
else branch, so PM5 (AT32) fell through and printed "Firmware... PM3 GENERIC"
even though the banner/Target/MCU already report PM5/AT32F437. Add an IfPm5()
branch that prints "Firmware... PM5" and the external-flash status.
Note: the "[ FPGA ] ... 2s30vq100" line in hw version is separate and comes
from the firmware-generated version string (fpga_version_info.c). On PM5 the
build reuses the Xilinx fpga_pm3_hf.bit only to generate that version info
(see Makefile.hal PM5 TODO), while the real Gowin FPGA is loaded via JTAG, so
the reported bitstream name is a placeholder. Fixing that is a firmware/build
change, not addressed here.
`hw version` and `hw status` decoded the reported chip id as an Atmel AT91
CIDR. On PM5 (AT32) the id is an ARM DBGMCU IDCODE, so it showed
"MCU Unknown", a bogus flash size (32 KB / 973% used) and "PM3 GENERIC".
- Client: when IfPm5(), print MCU "AT32F437" and the real flash size, and add
a "PM5" target line, instead of running the AT91 decode.
- Firmware: the flash size can't be derived from the AT32 IDCODE, so the device
now sends GetChipFlashSize(). It is appended AFTER the version string in the
CMD_VERSION reply, so the wire layout is unchanged and it stays compatible in
both directions (old client ignores the trailing bytes; new client length-
guards and treats a missing value as 0). GetChipFlashSize() already exists for
both AT91 and AT32.
Replace the hard-coded AT91 PDC register access in SniffIso14443a() with
cross-platform helpers for the RX double-buffer status/refresh, so the
sniffer no longer depends on AT91-specific registers.
- Add FPGA_SSC_DMA_RX_{Primary,Secondary}_Done and
FPGA_SSC_DMA_RX_Refresh_{Both,Secondary} to fpga_apis.h.
- AT91: primary maps to PDC RPR/RCR, secondary ("next") to RNPR/RNCR.
- AT32: no double buffer, so the primary path is a no-op and all re-arming
is done through the secondary (single-shot DMA re-arm).
Add the mkversion bat and ps1 implementation to the Windows platform compilation.
Make armlib a static library so that bootrom and armsrc can be reused.
in appmain.c and cmd added.
in cmd.c and add some code for test CEP
in em4x50.c(Do not timeout--)
in em4x70.c
in emvsim.c
in epa.c
in felica.c
in felicasim.c
in felicasim.c
in hfops.c
in hfsnoop.c
in hitag2.c
in hitag_common.c(Cross-platform implementation is incomplete.)
in hitagS.c
in hitagu.c
in i2c.c(Incomplete, continue to abstract.)
in i2c_direct.c
in iclass.c
in iso14443a.c(Sniff no finish yet)
in iso14443b.c and fixed bug for st25
in iso15693.c
in legicrf.c
in legicrfsim.c
in lfadc.c(lf_count_edge_periods_ex() improved)
in lfops.c(TI tag no finish yet)
in lfsampling.c
in lfzx.c
in mifarecmd.c
in mifaredesfire.c
in mifaresim.c
in mifaresniff_disabled.c
in mifareutil.c
in pcf7931.c
in sam_xxx
in secc & seos
in start.c
in thinfilm.c
in utils