1 parent
4cf2e83c3a
commit
c2aec48b49
6 files changed
+770
No files matched your search
+100
@@ -0,0 +1,100 @@
|
||||
//-----------------------------------------------------------------------------
|
||||
// Copyright (C) Proxmark3 contributors. See AUTHORS.md for details.
|
||||
//
|
||||
// This program is free software: you can redistribute it and/or modify
|
||||
// it under the terms of the GNU General Public License as published by
|
||||
// the Free Software Foundation, either version 3 of the License, or
|
||||
// (at your option) any later version.
|
||||
//
|
||||
// This program is distributed in the hope that it will be useful,
|
||||
// but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
// GNU General Public License for more details.
|
||||
//
|
||||
// See LICENSE.txt for the text of the license.
|
||||
//-----------------------------------------------------------------------------
|
||||
// PM5 (AT32F435) mainboard buzzer - see buzzer.h.
|
||||
//
|
||||
// Wiring: PB13 = enable (push-pull), PC9 = TMR8_CH4 PWM modulation. The bring-up
|
||||
// sequence is the one proven by the factory QC self-test.
|
||||
//-----------------------------------------------------------------------------
|
||||
|
||||
#include "buzzer.h"
|
||||
|
||||
#include "at32f435_437.h"
|
||||
#include "at32f435_437_crm.h"
|
||||
#include "at32f435_437_gpio.h"
|
||||
#include "at32f435_437_tmr.h"
|
||||
#include "ticks_apis.h" // SpinDelay
|
||||
|
||||
// Buzzer wiring on the PM5 mainboard.
|
||||
#define BUZZER_EN_GPIO GPIOB
|
||||
#define BUZZER_EN_PIN GPIO_PINS_13
|
||||
#define BUZZER_MOD_GPIO GPIOC
|
||||
#define BUZZER_MOD_PIN GPIO_PINS_9
|
||||
#define BUZZER_MOD_SRC GPIO_PINS_SOURCE9
|
||||
#define BUZZER_MOD_MUX GPIO_MUX_3
|
||||
#define BUZZER_MOD_TMR TMR8
|
||||
#define BUZZER_MOD_TMR_CH TMR_SELECT_CHANNEL_4
|
||||
|
||||
static bool s_buzzer_ready = false;
|
||||
|
||||
void BuzzerSetup(void) {
|
||||
crm_periph_clock_enable(CRM_GPIOB_PERIPH_CLOCK, TRUE);
|
||||
crm_periph_clock_enable(CRM_GPIOC_PERIPH_CLOCK, TRUE);
|
||||
crm_periph_clock_enable(CRM_TMR8_PERIPH_CLOCK, TRUE);
|
||||
|
||||
gpio_init_type gpio_init_struct;
|
||||
gpio_default_para_init(&gpio_init_struct);
|
||||
|
||||
// Enable pin (PB13): push-pull output, driven low = silent.
|
||||
gpio_init_struct.gpio_drive_strength = GPIO_DRIVE_STRENGTH_STRONGER;
|
||||
gpio_init_struct.gpio_out_type = GPIO_OUTPUT_PUSH_PULL;
|
||||
gpio_init_struct.gpio_mode = GPIO_MODE_OUTPUT;
|
||||
gpio_init_struct.gpio_pins = BUZZER_EN_PIN;
|
||||
gpio_init_struct.gpio_pull = GPIO_PULL_NONE;
|
||||
gpio_init(BUZZER_EN_GPIO, &gpio_init_struct);
|
||||
gpio_bits_write(BUZZER_EN_GPIO, BUZZER_EN_PIN, FALSE);
|
||||
|
||||
// Modulation pin (PC9): alternate function = TMR8_CH4.
|
||||
gpio_init_struct.gpio_mode = GPIO_MODE_MUX;
|
||||
gpio_init_struct.gpio_pins = BUZZER_MOD_PIN;
|
||||
gpio_init(BUZZER_MOD_GPIO, &gpio_init_struct);
|
||||
gpio_pin_mux_config(BUZZER_MOD_GPIO, BUZZER_MOD_SRC, BUZZER_MOD_MUX);
|
||||
|
||||
tmr_internal_clock_set(BUZZER_MOD_TMR);
|
||||
tmr_reset(BUZZER_MOD_TMR);
|
||||
tmr_base_init(BUZZER_MOD_TMR, BUZZER_DEFAULT_PERIOD, 95); // ~2 kHz from 192 MHz
|
||||
tmr_output_config_type tmr_output_struct;
|
||||
tmr_output_default_para_init(&tmr_output_struct);
|
||||
tmr_output_struct.oc_mode = TMR_OUTPUT_CONTROL_PWM_MODE_A;
|
||||
tmr_output_struct.oc_polarity = TMR_OUTPUT_ACTIVE_HIGH;
|
||||
tmr_output_struct.oc_output_state = TRUE;
|
||||
tmr_output_channel_config(BUZZER_MOD_TMR, BUZZER_MOD_TMR_CH, &tmr_output_struct);
|
||||
tmr_channel_value_set(BUZZER_MOD_TMR, BUZZER_MOD_TMR_CH, BUZZER_DEFAULT_DUTY);
|
||||
tmr_counter_enable(BUZZER_MOD_TMR, TRUE);
|
||||
tmr_output_enable(BUZZER_MOD_TMR, TRUE);
|
||||
|
||||
s_buzzer_ready = true;
|
||||
}
|
||||
|
||||
void BuzzerTone(uint16_t period, uint16_t duty, uint16_t on_ms) {
|
||||
if (s_buzzer_ready == false) {
|
||||
BuzzerSetup();
|
||||
}
|
||||
BUZZER_MOD_TMR->pr = period;
|
||||
tmr_channel_value_set(BUZZER_MOD_TMR, BUZZER_MOD_TMR_CH, duty);
|
||||
gpio_bits_write(BUZZER_EN_GPIO, BUZZER_EN_PIN, TRUE);
|
||||
SpinDelay(on_ms);
|
||||
gpio_bits_write(BUZZER_EN_GPIO, BUZZER_EN_PIN, FALSE);
|
||||
}
|
||||
|
||||
void BuzzerBeep(uint16_t on_ms) {
|
||||
BuzzerTone(BUZZER_DEFAULT_PERIOD, BUZZER_DEFAULT_DUTY, on_ms);
|
||||
}
|
||||
|
||||
void BuzzerOff(void) {
|
||||
if (s_buzzer_ready) {
|
||||
gpio_bits_write(BUZZER_EN_GPIO, BUZZER_EN_PIN, FALSE);
|
||||
}
|
||||
}
|
||||
@@ -0,0 +1,54 @@
|
||||
//-----------------------------------------------------------------------------
|
||||
// Copyright (C) Proxmark3 contributors. See AUTHORS.md for details.
|
||||
//
|
||||
// This program is free software: you can redistribute it and/or modify
|
||||
// it under the terms of the GNU General Public License as published by
|
||||
// the Free Software Foundation, either version 3 of the License, or
|
||||
// (at your option) any later version.
|
||||
//
|
||||
// This program is distributed in the hope that it will be useful,
|
||||
// but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
// GNU General Public License for more details.
|
||||
//
|
||||
// See LICENSE.txt for the text of the license.
|
||||
//-----------------------------------------------------------------------------
|
||||
// PM5 (AT32F435) mainboard buzzer.
|
||||
//
|
||||
// The buzzer is a piezo on PB13 (enable) driven by TMR8_CH4 PWM on PC9. This is
|
||||
// NOT BWM-specific hardware - it lives on the PM5 mainboard - so the API is
|
||||
// generic and any feature (QC self-test, BWM low-battery warning, ...) can use
|
||||
// it. Only the PM5 platform builds the implementation; callers must therefore
|
||||
// guard usage with #ifdef PM5 (or a PM5-only feature flag).
|
||||
//-----------------------------------------------------------------------------
|
||||
|
||||
#ifndef __BUZZER_H
|
||||
#define __BUZZER_H
|
||||
|
||||
#include "common.h"
|
||||
|
||||
// Default PWM period (TMR8 auto-reload) and compare value programmed by
|
||||
// BuzzerSetup(). period 999 with the /96 prescaler in the setup gives ~2 kHz
|
||||
// from the 192 MHz timer clock; duty 500 is ~50%.
|
||||
#define BUZZER_DEFAULT_PERIOD 999
|
||||
#define BUZZER_DEFAULT_DUTY 500
|
||||
|
||||
// One-time TMR8/GPIO bring-up. Safe to call more than once (it just re-runs the
|
||||
// init). BuzzerTone()/BuzzerBeep() call this automatically on first use, so most
|
||||
// callers never need to invoke it directly.
|
||||
void BuzzerSetup(void);
|
||||
|
||||
// Sound the buzzer for on_ms milliseconds at the given PWM period/duty.
|
||||
// period : TMR8 auto-reload value (higher period -> lower pitch)
|
||||
// duty : TMR8_CH4 compare value (~duty/period fraction)
|
||||
// Blocking (SpinDelay) - only call from a context that may block (e.g. the idle
|
||||
// loop or a self-test), never from inside a time-critical operation.
|
||||
void BuzzerTone(uint16_t period, uint16_t duty, uint16_t on_ms);
|
||||
|
||||
// Sound the buzzer for on_ms milliseconds at the default pitch/duty.
|
||||
void BuzzerBeep(uint16_t on_ms);
|
||||
|
||||
// Force the buzzer enable line low (silence). No-op if never set up.
|
||||
void BuzzerOff(void);
|
||||
|
||||
#endif // __BUZZER_H
|
||||
@@ -0,0 +1,424 @@
|
||||
//-----------------------------------------------------------------------------
|
||||
// Copyright (C) Proxmark3 contributors. See AUTHORS.md for details.
|
||||
//
|
||||
// This program is free software: you can redistribute it and/or modify
|
||||
// it under the terms of the GNU General Public License as published by
|
||||
// the Free Software Foundation, either version 3 of the License, or
|
||||
// (at your option) any later version.
|
||||
//
|
||||
// This program is distributed in the hope that it will be useful,
|
||||
// but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
// GNU General Public License for more details.
|
||||
//
|
||||
// See LICENSE.txt for the text of the license.
|
||||
//-----------------------------------------------------------------------------
|
||||
// Proxmark5 BWM charger (AW32001E) + fuel gauge (BQ27427) - see bwm_charger.h.
|
||||
//-----------------------------------------------------------------------------
|
||||
|
||||
#include "bwm_charger.h"
|
||||
|
||||
#if defined(WITH_BWM_CHARGERKICK) || defined(WITH_BWM_STATUS)
|
||||
|
||||
#include "i2c.h"
|
||||
#include "dbprint.h"
|
||||
#include "ticks_apis.h" // WaitMS / GetTickCount / GetTickCountDelta
|
||||
#include "ansi.h"
|
||||
|
||||
#ifdef WITH_BWM_LOWBATT_BEEP
|
||||
#include "buzzer.h" // generic mainboard buzzer API (not BWM-specific)
|
||||
#endif
|
||||
|
||||
// --- AW32001E charger register map (I2C 8-bit address 0x93) --------------------
|
||||
#define BWM_CHG_ADDR 0x93
|
||||
#define BWM_CHG_REG_MAINCTL 0x06 // bit5 = FET_DIS: shipping mode -> VMIX/charge path off
|
||||
#define BWM_CHG_REG_SYSSTAT 0x08 // system status (CHG_STAT / PG_STAT / THERM_STAT)
|
||||
#define BWM_CHG_REG_FAULT 0x09 // fault register (latched, read-on-clear)
|
||||
#define BWM_CHG_FET_DIS (1u << 5)
|
||||
|
||||
// --- BQ27427 fuel gauge (I2C 8-bit address 0xAA = 7-bit 0x55 << 1) -------------
|
||||
#define BWM_GAUGE_ADDR 0xAA
|
||||
// Standard commands (16-bit, little-endian)
|
||||
#define BWM_GAUGE_TEMP 0x02 // 0.1 K
|
||||
#define BWM_GAUGE_VOLTAGE 0x04 // mV
|
||||
#define BWM_GAUGE_REMCAP 0x0C // mAh
|
||||
#define BWM_GAUGE_FCC 0x0E // mAh, FullChargeCapacity (health: FCC/design cap)
|
||||
#define BWM_GAUGE_CURRENT 0x10 // signed mA
|
||||
#define BWM_GAUGE_SOC 0x1C // %
|
||||
|
||||
#endif // WITH_BWM_CHARGERKICK || WITH_BWM_STATUS
|
||||
|
||||
#ifdef WITH_BWM_CHARGERKICK
|
||||
// Emergency charge-enable. Normal PM5 firmware never touches the charger, so a BWM
|
||||
// left in shipping/FET-disabled mode won't take charge even with USB present. This
|
||||
// wakes the power path at boot so the AW32001 can charge autonomously.
|
||||
//
|
||||
// SCOPE: runs from AppMain(), i.e. only once the PM5 has actually booted. It cannot
|
||||
// help a cell too flat to boot (that needs USB reaching VUSBIN in hardware), and it
|
||||
// cannot reroute VBUS to the charger input. It only ensures that when the charger
|
||||
// HAS input, its path is enabled.
|
||||
void bwm_charger_kick(void) {
|
||||
I2C_init(true);
|
||||
WaitMS(2); // let the bus settle
|
||||
|
||||
uint8_t v = 0;
|
||||
// No ACK -> BWM absent or charger dead. Nothing to do; leave the bus and return.
|
||||
if (I2C_BufferReadRaw(&v, 1, BWM_CHG_REG_MAINCTL, BWM_CHG_ADDR) <= 0) {
|
||||
return;
|
||||
}
|
||||
|
||||
// Shipping / FET-disabled -> clear it so the power/charge path comes alive.
|
||||
if (v & BWM_CHG_FET_DIS) {
|
||||
uint8_t nv = v & ~BWM_CHG_FET_DIS;
|
||||
if (I2C_BufferWrite(&nv, 1, BWM_CHG_REG_MAINCTL, BWM_CHG_ADDR)) {
|
||||
Dbprintf("[BWM] charger was FET-disabled (0x%02x) - path re-enabled", v);
|
||||
} else {
|
||||
Dbprintf(_RED_("[BWM] charger FET-disabled; re-enable write failed"));
|
||||
}
|
||||
}
|
||||
}
|
||||
#endif // WITH_BWM_CHARGERKICK
|
||||
|
||||
#ifdef WITH_BWM_STATUS
|
||||
// BWM battery telemetry for `hw status`.
|
||||
// The BQ27427 address/commands and the current-sign convention are the TI standard
|
||||
// set - confirm against a known-charging module before trusting absolute values. If
|
||||
// the gauge or charger doesn't ACK, the corresponding lines print "not responding"
|
||||
// rather than reporting garbage, so this is safe to ship even if an address is wrong
|
||||
// on a given board.
|
||||
static bool g_bwm_present = false;
|
||||
|
||||
static bool bwm_gauge_read16(uint8_t cmd, uint16_t *out) {
|
||||
uint8_t d[2] = {0};
|
||||
if (I2C_BufferReadRaw(d, 2, cmd, BWM_GAUGE_ADDR) <= 0) {
|
||||
return false;
|
||||
}
|
||||
*out = (uint16_t)(d[0] | (d[1] << 8)); // little-endian
|
||||
return true;
|
||||
}
|
||||
|
||||
static bool bq_read_design_cap(uint16_t *cap); // fwd decl (defined with the provisioning code below)
|
||||
|
||||
// Reads the BWM charger + fuel gauge and prints a battery section. Called from
|
||||
// SendStatus() under #ifdef PM5, so it only runs on a booted PM5 with I2C available.
|
||||
void bwm_print_battery_status(void) {
|
||||
if (g_bwm_present == false) {
|
||||
return; // no BWM detected at boot; nothing to report
|
||||
}
|
||||
DbpString(_CYAN_("Battery / BWM"));
|
||||
|
||||
I2C_init(true);
|
||||
WaitMS(2); // let the bus settle
|
||||
|
||||
// --- charger (AW32001) ---
|
||||
// REG09 (Fault) latches faults and is read-on-clear: read it TWICE - the 1st read
|
||||
// returns the latched history, the 2nd returns the live state (datasheet: "read
|
||||
// REG09 two times consecutively"). Bits [7:6] are the EN_SHIPPING_DGL config field,
|
||||
// not faults, so mask to 0x3F. Fault bit map (AW32001E REG09H):
|
||||
// b5 VIN_FAULT b4 THERM_SD b3 BAT_OVP b2 SAFETY_TMR b1 NTC_HOT b0 NTC_COLD
|
||||
uint8_t mainctl = 0, f1 = 0, fault = 0, sysstat = 0;
|
||||
if (I2C_BufferReadRaw(&mainctl, 1, BWM_CHG_REG_MAINCTL, BWM_CHG_ADDR) <= 0) {
|
||||
Dbprintf(" Charger............. " _YELLOW_("not responding") " (BWM absent or I2C down)");
|
||||
} else {
|
||||
Dbprintf(" Charger MainCtl..... 0x%02x %s", mainctl,
|
||||
(mainctl & BWM_CHG_FET_DIS) ? _RED_("FET_DIS (VMIX off / shipping)")
|
||||
: _GREEN_("power path enabled"));
|
||||
|
||||
I2C_BufferReadRaw(&f1, 1, BWM_CHG_REG_FAULT, BWM_CHG_ADDR); // 1st = latched history
|
||||
I2C_BufferReadRaw(&fault, 1, BWM_CHG_REG_FAULT, BWM_CHG_ADDR); // 2nd = current state
|
||||
fault &= 0x3F;
|
||||
|
||||
if (fault == 0) {
|
||||
Dbprintf(" Charger fault....... 0x00 (none)");
|
||||
} else {
|
||||
Dbprintf(" Charger fault....... " _RED_("0x%02x") "%s%s%s%s%s%s", fault,
|
||||
(fault & 0x20) ? " VIN_FAULT" : "",
|
||||
(fault & 0x10) ? " THERM_SD" : "",
|
||||
(fault & 0x08) ? " BAT_OVP" : "",
|
||||
(fault & 0x04) ? " SAFETY_TMR" : "",
|
||||
(fault & 0x02) ? " NTC_HOT" : "",
|
||||
(fault & 0x01) ? " NTC_COLD" : "");
|
||||
}
|
||||
|
||||
// Live charge state from REG08 (System Status): CHG_STAT[4:3], PG_STAT[1], THERM_STAT[0]
|
||||
if (I2C_BufferReadRaw(&sysstat, 1, BWM_CHG_REG_SYSSTAT, BWM_CHG_ADDR) > 0) {
|
||||
static const char *cs[] = { "not charging", "pre-charge", "charging", "charge done" };
|
||||
Dbprintf(" Charge status....... %s%s%s", cs[(sysstat >> 3) & 0x03],
|
||||
(sysstat & 0x02) ? ", power good" : ", power fail",
|
||||
(sysstat & 0x01) ? ", thermal-reg" : "");
|
||||
}
|
||||
|
||||
// Configured charge profile (read-only). Decode tables from AW32001E datasheet V1.4:
|
||||
// IIN_LIM (REG00[3:0]): 0000=50mA, else 80mA + 30mA*(code-1) [1111=500mA]
|
||||
// VIN_DPM (REG00[7:4]): 3880mV + 80mV*code [1000=4.52V default]
|
||||
// ICHG (REG02[5:0]): 8mA * (code+1) [63=512mA]
|
||||
uint8_t reg00 = 0, reg01 = 0, reg02 = 0;
|
||||
if (I2C_BufferReadRaw(®00, 1, 0x00, BWM_CHG_ADDR) > 0) {
|
||||
uint8_t iin = reg00 & 0x0F;
|
||||
uint8_t vdpm = (reg00 >> 4) & 0x0F;
|
||||
uint16_t iin_ma = (iin == 0) ? 50 : (80 + 30 * (iin - 1));
|
||||
uint16_t vdpm_mv = 3880 + 80 * vdpm;
|
||||
Dbprintf(" Input limit......... %u mA, VIN_DPM %u.%02u V",
|
||||
iin_ma, vdpm_mv / 1000, (vdpm_mv % 1000) / 10);
|
||||
}
|
||||
if (I2C_BufferReadRaw(®01, 1, 0x01, BWM_CHG_ADDR) > 0) {
|
||||
Dbprintf(" Charge enable....... %s", (reg01 & (1u << 3)) ? _YELLOW_("disabled") : _GREEN_("enabled"));
|
||||
}
|
||||
if (I2C_BufferReadRaw(®02, 1, 0x02, BWM_CHG_ADDR) > 0) {
|
||||
uint16_t ichg_ma = 8 * ((reg02 & 0x3F) + 1);
|
||||
Dbprintf(" Charge current...... %u mA", ichg_ma);
|
||||
}
|
||||
}
|
||||
|
||||
// --- fuel gauge (BQ27427) ---
|
||||
uint16_t soc = 0, mv = 0, rem = 0, temp = 0, raw_i = 0;
|
||||
if (bwm_gauge_read16(BWM_GAUGE_SOC, &soc) && bwm_gauge_read16(BWM_GAUGE_VOLTAGE, &mv)) {
|
||||
bwm_gauge_read16(BWM_GAUGE_REMCAP, &rem);
|
||||
bwm_gauge_read16(BWM_GAUGE_TEMP, &temp);
|
||||
bwm_gauge_read16(BWM_GAUGE_CURRENT, &raw_i);
|
||||
|
||||
int16_t cur = (int16_t)raw_i; // +charge / -discharge (verify polarity on hw)
|
||||
int tempC10 = (int)temp - 2732; // 0.1 K -> 0.1 C
|
||||
int tabs = (tempC10 < 0) ? -tempC10 : tempC10;
|
||||
|
||||
Dbprintf(" Battery SoC......... %u %%", soc);
|
||||
Dbprintf(" Battery voltage..... %u mV", mv);
|
||||
Dbprintf(" Battery current..... %d mA %s", cur,
|
||||
(cur > 5) ? _GREEN_("(charging)") :
|
||||
(cur < -5) ? _YELLOW_("(discharging)") : "(idle)");
|
||||
Dbprintf(" Remaining capacity.. %u mAh", rem);
|
||||
// Measured drain / projected runtime: when running on battery the gauge
|
||||
// Current is negative (discharging); |cur| is the real system draw, so
|
||||
// remaining runtime ~= RemainingCapacity / draw. Only meaningful while
|
||||
// discharging - on charge or idle there is no drain figure to report.
|
||||
// (Projection is only as good as RemCap - provision Design Capacity first.)
|
||||
if (cur < -5) {
|
||||
uint16_t draw = (uint16_t)(-cur); // mA drawn from the battery
|
||||
uint32_t mins = ((uint32_t)rem * 60) / draw; // RemCap/draw -> hours, *60 -> mins
|
||||
Dbprintf(" Battery drain....... %u mA (approx %u h %u min left)",
|
||||
draw, (unsigned)(mins / 60), (unsigned)(mins % 60));
|
||||
}
|
||||
Dbprintf(" Temp (gauge)........ %d.%d C", tempC10 / 10, tabs % 10);
|
||||
|
||||
// Battery health: FullChargeCapacity (0x0E) vs the gauge's programmed Design
|
||||
// Capacity. FCC is the gauge's learned present full capacity; health = FCC/design.
|
||||
// NOTE: only meaningful once the gauge has run an Impedance Track learning cycle
|
||||
// (a full charge/discharge). Before that it is an unconverged estimate. If Design
|
||||
// Capacity was never provisioned (hw bwmsetcap), the ratio is against the gauge
|
||||
// default, not the fitted cell - so it can read wildly wrong.
|
||||
uint16_t fcc = 0, design = 0;
|
||||
if (bwm_gauge_read16(BWM_GAUGE_FCC, &fcc) && fcc > 0) {
|
||||
if (bq_read_design_cap(&design) == false || design == 0) {
|
||||
design = BWM_DEFAULT_DESIGN_CAP_MAH; // fall back to the fitted-cell rating
|
||||
}
|
||||
unsigned health = (unsigned)(((uint32_t)fcc * 100) / design);
|
||||
Dbprintf(" Full charge cap..... %u mAh (design %u)", fcc, design);
|
||||
Dbprintf(" Battery health...... %u %% " _YELLOW_("(needs a full cycle to be accurate)"), health);
|
||||
}
|
||||
} else {
|
||||
Dbprintf(" Fuel gauge.......... " _YELLOW_("not responding") " (BQ27427 absent or I2C down)");
|
||||
}
|
||||
}
|
||||
|
||||
// --- BQ27427 provisioning: set Design Capacity for the fitted cell -------------
|
||||
// One-time. The gauge ships with a ~1000+ mAh default profile, so RemainingCapacity
|
||||
// reads wrong for the fitted pack until Design Capacity is programmed. Invoked by the
|
||||
// `hw bwmsetcap` client command (CMD_PM5_BWM_SET_CAP) - deliberately NOT run at boot,
|
||||
// because a config-update cycle disrupts the Impedance Track learning cycle.
|
||||
// Per BQ27427 TRM (SLUUCD5): State subclass 82 (0x52), Design Capacity at offset 6
|
||||
// -> block addr 0x46 (MSB)/0x47 (LSB), big-endian. Assumes gauge UNSEALED (factory default).
|
||||
|
||||
static bool bq_control(uint16_t sub) {
|
||||
uint8_t d[2] = { (uint8_t)(sub & 0xFF), (uint8_t)(sub >> 8) };
|
||||
return I2C_BufferWrite(d, 2, 0x00, BWM_GAUGE_ADDR); // Control() 0x00
|
||||
}
|
||||
static bool bq_flags(uint16_t *f) {
|
||||
uint8_t d[2] = {0};
|
||||
if (I2C_BufferReadRaw(d, 2, 0x06, BWM_GAUGE_ADDR) <= 0) return false;
|
||||
*f = (uint16_t)(d[0] | (d[1] << 8)); // Flags() 0x06
|
||||
return true;
|
||||
}
|
||||
static bool bq_select_state_block(void) {
|
||||
uint8_t v;
|
||||
v = 0x00;
|
||||
if (!I2C_BufferWrite(&v, 1, 0x61, BWM_GAUGE_ADDR)) return false; // BlockDataControl
|
||||
v = 0x52;
|
||||
if (!I2C_BufferWrite(&v, 1, 0x3E, BWM_GAUGE_ADDR)) return false; // DataClass = 82 (State)
|
||||
v = 0x00;
|
||||
if (!I2C_BufferWrite(&v, 1, 0x3F, BWM_GAUGE_ADDR)) return false; // DataBlock = 0
|
||||
WaitMS(5);
|
||||
return true;
|
||||
}
|
||||
static bool bq_read_design_cap(uint16_t *cap) {
|
||||
if (!bq_select_state_block()) return false;
|
||||
uint8_t d[2] = {0};
|
||||
if (I2C_BufferReadRaw(d, 2, 0x46, BWM_GAUGE_ADDR) <= 0) return false;
|
||||
*cap = (uint16_t)((d[0] << 8) | d[1]); // big-endian
|
||||
return true;
|
||||
}
|
||||
|
||||
// Enable or disable battery charging by clearing/setting CEB (REG01[3]:
|
||||
// 0 = charge enabled, 1 = charge disabled). Read-modify-write to preserve the
|
||||
// other REG01 fields. NOTE: REG01 is watchdog-affected on the AW32001E - this
|
||||
// reverts to its default on watchdog expiry (~160 s) unless the watchdog is
|
||||
// serviced (REG02[6]=1) or disabled (REG05[6:5]=00), so treat it as a one-shot.
|
||||
bool bwm_charger_set_charge(bool enable) {
|
||||
uint8_t reg01 = 0;
|
||||
if (I2C_BufferReadRaw(®01, 1, 0x01, BWM_CHG_ADDR) <= 0) {
|
||||
return false;
|
||||
}
|
||||
if (enable) {
|
||||
reg01 &= ~(1u << 3); // CEB = 0 -> charge enabled
|
||||
} else {
|
||||
reg01 |= (1u << 3); // CEB = 1 -> charge disabled
|
||||
}
|
||||
return I2C_BufferWrite(®01, 1, 0x01, BWM_CHG_ADDR);
|
||||
}
|
||||
|
||||
// Program Design Capacity (and matching Design Energy). Idempotent: returns true
|
||||
// without a config-update cycle if the value is already correct.
|
||||
bool bwm_gauge_provision_capacity(uint16_t cap_mah) {
|
||||
uint16_t cur = 0;
|
||||
if (bq_read_design_cap(&cur) && cur == cap_mah) {
|
||||
return true; // already correct - do NOT run another CFGUPDATE cycle
|
||||
}
|
||||
|
||||
uint16_t energy_mwh = (uint16_t)(((uint32_t)cap_mah * 37) / 10); // ~3.7 V nominal
|
||||
|
||||
// Enter CONFIG_UPDATE and wait for the gauge to acknowledge it.
|
||||
if (bq_control(0x0013) == false) { // SET_CFGUPDATE
|
||||
return false;
|
||||
}
|
||||
|
||||
uint16_t flags = 0;
|
||||
int tries = 0;
|
||||
do {
|
||||
WaitMS(50);
|
||||
if (bq_flags(&flags) == false) {
|
||||
return false;
|
||||
}
|
||||
} while (((flags & 0x0010) == 0) && (++tries < 40)); // wait for CFGUPDATE (Flags bit 4), ~2 s
|
||||
|
||||
if ((flags & 0x0010) == 0) {
|
||||
return false;
|
||||
}
|
||||
|
||||
if (!bq_select_state_block()) return false;
|
||||
|
||||
uint8_t blk[32] = {0};
|
||||
if (I2C_BufferReadRaw(blk, 32, 0x40, BWM_GAUGE_ADDR) <= 0) return false;
|
||||
|
||||
blk[6] = (uint8_t)(cap_mah >> 8);
|
||||
blk[7] = (uint8_t)(cap_mah & 0xFF); // DesignCapacity
|
||||
blk[8] = (uint8_t)(energy_mwh >> 8);
|
||||
blk[9] = (uint8_t)(energy_mwh & 0xFF); // DesignEnergy
|
||||
I2C_BufferWrite(&blk[6], 2, 0x46, BWM_GAUGE_ADDR);
|
||||
I2C_BufferWrite(&blk[8], 2, 0x48, BWM_GAUGE_ADDR);
|
||||
|
||||
uint16_t sum = 0; // block checksum = 255 - (sum mod 256)
|
||||
for (int i = 0; i < 32; i++) sum += blk[i];
|
||||
uint8_t csum = (uint8_t)(0xFF - (uint8_t)(sum & 0xFF));
|
||||
I2C_BufferWrite(&csum, 1, 0x60, BWM_GAUGE_ADDR); // commit block
|
||||
WaitMS(10);
|
||||
|
||||
if (!bq_control(0x0042)) return false; // SOFT_RESET (exit CFGUPDATE)
|
||||
tries = 0;
|
||||
do { WaitMS(50); if (!bq_flags(&flags)) return false; }
|
||||
while (((flags & 0x0010) != 0) && (++tries < 40));
|
||||
return ((flags & 0x0010) == 0);
|
||||
}
|
||||
|
||||
// Enable battery charging on the BWM by replicating the charger register writes
|
||||
// from at32_unit_test.c:test_bat_charger_only_settings() (upstream RRG values),
|
||||
// WITHOUT pulling in that file's unrelated UART-debug / RGB test routines.
|
||||
// AW32001E @ 0x93:
|
||||
// REG01[3] CEB -> 0 : charge enabled
|
||||
// REG02 ICHG = 0x1F : 256 mA charge current
|
||||
// REG05 = 0x1A : safety timer disabled (upstream)
|
||||
// REG03 = 0xE1 : 3 A discharge current
|
||||
// REG0B = 0x6B : 11 mA pre-charge current
|
||||
//
|
||||
// Probe for the BWM charger over I2C and, if found, apply the charge configuration.
|
||||
void bwm_detect_and_init(void) {
|
||||
I2C_init(true);
|
||||
|
||||
// Single bounded probe. Any non-ACK => no BWM fitted; skip everything.
|
||||
uint8_t v = 0;
|
||||
if (I2C_BufferReadRaw(&v, 1, 0x01, BWM_CHG_ADDR) <= 0) {
|
||||
g_bwm_present = false;
|
||||
return;
|
||||
}
|
||||
g_bwm_present = true;
|
||||
|
||||
// Enable charging (clear CEB, REG01[3]) + upstream charge profile
|
||||
// (matches at32_unit_test.c:test_bat_charger_only_settings(), AW32001ECSR).
|
||||
if (v & (1u << 3)) {
|
||||
v &= ~(1u << 3);
|
||||
I2C_BufferWrite(&v, 1, 0x01, BWM_CHG_ADDR);
|
||||
}
|
||||
uint8_t w;
|
||||
w = 0x1F; I2C_BufferWrite(&w, 1, 0x02, BWM_CHG_ADDR); // charge current 256 mA
|
||||
w = 0xE1; I2C_BufferWrite(&w, 1, 0x03, BWM_CHG_ADDR); // discharge current 3 A
|
||||
w = 0x1A; I2C_BufferWrite(&w, 1, 0x05, BWM_CHG_ADDR); // safety timer disabled (upstream)
|
||||
w = 0x6B; I2C_BufferWrite(&w, 1, 0x0B, BWM_CHG_ADDR); // pre-charge 11 mA
|
||||
}
|
||||
#endif // WITH_BWM_STATUS
|
||||
|
||||
#ifdef WITH_BWM_LOWBATT_BEEP
|
||||
#ifndef WITH_BWM_STATUS
|
||||
#error "WITH_BWM_LOWBATT_BEEP requires WITH_BWM_STATUS (for the fuel-gauge reads)"
|
||||
#endif
|
||||
|
||||
// Low-battery audible warning (opt-in via WITH_BWM_LOWBATT_BEEP). Reuses the
|
||||
// WITH_BWM_STATUS fuel-gauge/charger reads and the generic mainboard buzzer. A
|
||||
// beeping device surprises people, so this is off by default.
|
||||
|
||||
// Thresholds - all overridable from the build if needed.
|
||||
#ifndef BWM_LOWBATT_SOC_PCT
|
||||
#define BWM_LOWBATT_SOC_PCT 10 // warn at or below this state-of-charge (%)
|
||||
#endif
|
||||
#ifndef BWM_LOWBATT_MV
|
||||
#define BWM_LOWBATT_MV 3500 // ...and only if pack voltage is under this (mV)
|
||||
#endif
|
||||
#ifndef BWM_LOWBATT_PERIOD_MS
|
||||
#define BWM_LOWBATT_PERIOD_MS 30000 // re-check at most this often
|
||||
#endif
|
||||
|
||||
// Two short chirps - the low-battery signature.
|
||||
static void bwm_beep_low_batt(void) {
|
||||
BuzzerBeep(80);
|
||||
SpinDelay(80);
|
||||
BuzzerBeep(80);
|
||||
}
|
||||
|
||||
// Throttled low-battery poll. Only warns on battery (USB absent) when BOTH the
|
||||
// state-of-charge and the pack voltage are below their floors. Silent while
|
||||
// charging or if the BWM/gauge is not present.
|
||||
void bwm_lowbatt_check(void) {
|
||||
static uint32_t last_tick = 0;
|
||||
|
||||
if ((last_tick != 0) && (GetTickCountDelta(last_tick) < BWM_LOWBATT_PERIOD_MS)) {
|
||||
return;
|
||||
}
|
||||
last_tick = GetTickCount();
|
||||
|
||||
uint8_t sysstat = 0;
|
||||
if (I2C_BufferReadRaw(&sysstat, 1, BWM_CHG_REG_SYSSTAT, BWM_CHG_ADDR) <= 0) {
|
||||
return; // no BWM / I2C error - stay quiet
|
||||
}
|
||||
if (sysstat & 0x02) {
|
||||
return; // power good (USB present) -> charging/idle, don't warn
|
||||
}
|
||||
|
||||
uint16_t soc = 0, mv = 0;
|
||||
if ((bwm_gauge_read16(BWM_GAUGE_SOC, &soc) == false) ||
|
||||
(bwm_gauge_read16(BWM_GAUGE_VOLTAGE, &mv) == false)) {
|
||||
return;
|
||||
}
|
||||
if ((soc > BWM_LOWBATT_SOC_PCT) || (mv >= BWM_LOWBATT_MV)) {
|
||||
return; // still healthy
|
||||
}
|
||||
|
||||
bwm_beep_low_batt(); // BuzzerBeep() lazily sets the buzzer up on first use
|
||||
}
|
||||
#endif // WITH_BWM_LOWBATT_BEEP
|
||||
@@ -0,0 +1,70 @@
|
||||
//-----------------------------------------------------------------------------
|
||||
// Copyright (C) Proxmark3 contributors. See AUTHORS.md for details.
|
||||
//
|
||||
// This program is free software: you can redistribute it and/or modify
|
||||
// it under the terms of the GNU General Public License as published by
|
||||
// the Free Software Foundation, either version 3 of the License, or
|
||||
// (at your option) any later version.
|
||||
//
|
||||
// This program is distributed in the hope that it will be useful,
|
||||
// but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
// GNU General Public License for more details.
|
||||
//
|
||||
// See LICENSE.txt for the text of the license.
|
||||
//-----------------------------------------------------------------------------
|
||||
// Proxmark5 BWM (Battery Wireless Module) power subsystem.
|
||||
//
|
||||
// Charger : AW32001E @ I2C 0x93 (8-bit form the I2C_* API uses)
|
||||
// Fuel gauge: BQ27427 @ I2C 7-bit 0x55 (0xAA 8-bit)
|
||||
//
|
||||
// Everything here is opt-in via the WITH_BWM_* build flags and only meaningful
|
||||
// on PLATFORM=PM5 (AT32F435) with a BWM fitted. If the BWM/charger/gauge does
|
||||
// not ACK on I2C, each entry point degrades gracefully rather than reporting
|
||||
// garbage.
|
||||
//-----------------------------------------------------------------------------
|
||||
|
||||
#ifndef __BWM_CHARGER_H
|
||||
#define __BWM_CHARGER_H
|
||||
|
||||
#include "common.h"
|
||||
|
||||
// Reference design capacity for the fitted cell (VXE 502540, 500 mAh / 3.7 V).
|
||||
// Used as the default target for `hw bwmsetcap` and as the fall-back divisor for
|
||||
// the battery-health estimate.
|
||||
#define BWM_DEFAULT_DESIGN_CAP_MAH 500
|
||||
|
||||
#ifdef WITH_BWM_CHARGERKICK
|
||||
// Emergency charge-path enable. Clears the AW32001 shipping/FET-disabled state so
|
||||
// the charger can run autonomously when it has input. Safe no-op if no BWM ACKs.
|
||||
// Runs from AppMain() (post-boot), so it cannot revive a cell too flat to boot.
|
||||
void bwm_charger_kick(void);
|
||||
#endif // WITH_BWM_CHARGERKICK
|
||||
|
||||
#ifdef WITH_BWM_STATUS
|
||||
// Probe for the BWM charger over I2C and, if present, apply the charge profile.
|
||||
// Records presence for bwm_print_battery_status(). Call once early in AppMain().
|
||||
void bwm_detect_and_init(void);
|
||||
|
||||
// Print the "Battery / BWM" section for `hw status`. Silent if no BWM was
|
||||
// detected by bwm_detect_and_init().
|
||||
void bwm_print_battery_status(void);
|
||||
|
||||
// One-time BQ27427 Design Capacity provisioning (CMD_PM5_BWM_SET_CAP /
|
||||
// `hw bwmsetcap`). Idempotent - returns true without a CFGUPDATE cycle if the
|
||||
// value is already correct. Assumes the gauge is UNSEALED (factory default).
|
||||
bool bwm_gauge_provision_capacity(uint16_t cap_mah);
|
||||
|
||||
// Enable/disable battery charging (clear/set AW32001E CEB, REG01[3]).
|
||||
// One-shot: reverts on the charger watchdog timeout (~160 s).
|
||||
bool bwm_charger_set_charge(bool enable);
|
||||
#endif // WITH_BWM_STATUS
|
||||
|
||||
#ifdef WITH_BWM_LOWBATT_BEEP
|
||||
// Throttled low-battery poll. On battery (USB absent) with both SoC and pack
|
||||
// voltage below their floors, chirps the mainboard buzzer. Call from the idle
|
||||
// loop. Requires WITH_BWM_STATUS (for the fuel-gauge reads).
|
||||
void bwm_lowbatt_check(void);
|
||||
#endif // WITH_BWM_LOWBATT_BEEP
|
||||
|
||||
#endif // __BWM_CHARGER_H
|
||||
@@ -0,0 +1,79 @@
|
||||
//-----------------------------------------------------------------------------
|
||||
// Copyright (C) Proxmark3 contributors. See AUTHORS.md for details.
|
||||
//
|
||||
// This program is free software: you can redistribute it and/or modify
|
||||
// it under the terms of the GNU General Public License as published by
|
||||
// the Free Software Foundation, either version 3 of the License, or
|
||||
// (at your option) any later version.
|
||||
//
|
||||
// This program is distributed in the hope that it will be useful,
|
||||
// but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
// GNU General Public License for more details.
|
||||
//
|
||||
// See LICENSE.txt for the text of the license.
|
||||
//-----------------------------------------------------------------------------
|
||||
// PM5 antenna-RGB "alive on battery" indicator - see rgb_indicator.h.
|
||||
//-----------------------------------------------------------------------------
|
||||
|
||||
#include "rgb_indicator.h"
|
||||
|
||||
#ifdef WITH_PM5_PWR_LED
|
||||
|
||||
#include "rgb_apis.h" // RgbLedSet
|
||||
#include "gpio_apis.h" // gpio_vusb_setup / Gpio_VUSB_Read (USB-present detection)
|
||||
#include "ticks_apis.h" // GetTickCount / GetTickCountDelta
|
||||
|
||||
#ifndef PM5_PWR_LED_PERIOD_MS
|
||||
#define PM5_PWR_LED_PERIOD_MS 1000 // re-evaluate at most once a second
|
||||
#endif
|
||||
|
||||
// Set via rgb_indicator_set_external() so the indicator backs off while tune
|
||||
// (or any external RGB user) controls the LED.
|
||||
static volatile bool s_rgb_external = false;
|
||||
static bool s_pwr_led_setup = false;
|
||||
|
||||
void rgb_indicator_set_external(bool owned) {
|
||||
s_rgb_external = owned;
|
||||
}
|
||||
|
||||
// "Alive on battery" indicator. When the PM5 runs on battery (USB unplugged) it
|
||||
// otherwise gives no sign it is on, so users leave it draining. This lights the
|
||||
// antenna RGB a dim green while on battery, and turns it off when on USB (where the
|
||||
// cable already signals power). Throttled + edge-triggered to avoid I2C spam and to
|
||||
// yield the RGB to hf/lf tune (which claims it via rgb_indicator_set_external()).
|
||||
void rgb_indicator_update(void) {
|
||||
static uint32_t last_tick = 0;
|
||||
static int last_state = -1; // -1 unknown, 0 = off/USB, 1 = green/battery
|
||||
|
||||
if ((last_tick != 0) && (GetTickCountDelta(last_tick) < PM5_PWR_LED_PERIOD_MS)) {
|
||||
return;
|
||||
}
|
||||
last_tick = GetTickCount();
|
||||
|
||||
// While tune (or any external RGB user) owns the LED, do nothing and force a
|
||||
// refresh next time it is released.
|
||||
if (s_rgb_external) {
|
||||
last_state = -1;
|
||||
return;
|
||||
}
|
||||
|
||||
if (s_pwr_led_setup == false) {
|
||||
gpio_vusb_setup();
|
||||
s_pwr_led_setup = true;
|
||||
}
|
||||
|
||||
int on_battery = (Gpio_VUSB_Read() == false) ? 1 : 0;
|
||||
if (on_battery == last_state) {
|
||||
return; // edge-triggered: only write RGB when the state changes
|
||||
}
|
||||
last_state = on_battery;
|
||||
|
||||
if (on_battery) {
|
||||
RgbLedSet(0, 8, 0); // dim green: alive, on battery
|
||||
} else {
|
||||
RgbLedSet(0, 0, 0); // on USB: off (cable already signals power)
|
||||
}
|
||||
}
|
||||
|
||||
#endif // WITH_PM5_PWR_LED
|
||||
@@ -0,0 +1,43 @@
|
||||
//-----------------------------------------------------------------------------
|
||||
// Copyright (C) Proxmark3 contributors. See AUTHORS.md for details.
|
||||
//
|
||||
// This program is free software: you can redistribute it and/or modify
|
||||
// it under the terms of the GNU General Public License as published by
|
||||
// the Free Software Foundation, either version 3 of the License, or
|
||||
// (at your option) any later version.
|
||||
//
|
||||
// This program is distributed in the hope that it will be useful,
|
||||
// but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
// GNU General Public License for more details.
|
||||
//
|
||||
// See LICENSE.txt for the text of the license.
|
||||
//-----------------------------------------------------------------------------
|
||||
// PM5 antenna-RGB "alive on battery" indicator (WITH_PM5_PWR_LED).
|
||||
//
|
||||
// Policy layer on top of the low-level RGB driver (rgb_apis.h / RgbLedSet): lights
|
||||
// the antenna RGB dim green while the PM5 runs on battery and turns it off on USB.
|
||||
// It also arbitrates ownership of the LED with `hf/lf tune --rgb`, which claims the
|
||||
// RGB directly via CMD_PM5_RGB_SET.
|
||||
//-----------------------------------------------------------------------------
|
||||
|
||||
#ifndef __RGB_INDICATOR_H
|
||||
#define __RGB_INDICATOR_H
|
||||
|
||||
#include "common.h"
|
||||
|
||||
#ifdef WITH_PM5_PWR_LED
|
||||
|
||||
// Throttled + edge-triggered indicator update. Call from the idle loop: it only
|
||||
// touches the RGB over I2C when the USB-present state actually changes, and it
|
||||
// yields the LED entirely while an external user (tune) owns it.
|
||||
void rgb_indicator_update(void);
|
||||
|
||||
// Claim/release the RGB for an external user (e.g. tune). While claimed, the
|
||||
// indicator leaves the LED alone; releasing it forces a refresh next update.
|
||||
// `owned` = true when a non-zero colour was set, false when cleared.
|
||||
void rgb_indicator_set_external(bool owned);
|
||||
|
||||
#endif // WITH_PM5_PWR_LED
|
||||
|
||||
#endif // __RGB_INDICATOR_H
|
||||
Reference in new issue
Block a user