Merge pull request #3715 from xianglin1998/fpga-timing-bug
Fixed: FPGA PWM clock timing failed to meet the 400 MHz requirement.
This commit is contained in:
3 files changed
+34
-18
No files matched your search
+31
-16
@@ -25,7 +25,7 @@ module fpga_top (
|
||||
input cross_lo,
|
||||
input spi_mosi,
|
||||
input ssp_dout,
|
||||
input module_sel, // 选择模块,1=HF,0=LF
|
||||
input module_sel, // module select: 1 = HF, 0 = LF
|
||||
|
||||
output ssp_din,
|
||||
output ssp_frame,
|
||||
@@ -41,45 +41,60 @@ module fpga_top (
|
||||
output dbg2,
|
||||
output dbgled,
|
||||
|
||||
output clk_gate, //门控输出,控制切断外部13.56m
|
||||
output pwr_pwm, //升压器输出,pwm控制升压电压
|
||||
output pan_en, //模拟供电使能
|
||||
output pdp_en //升压器使能
|
||||
output clk_gate, // gates the external 13.56 MHz clock
|
||||
output pwr_pwm, // boost converter PWM, sets the driver supply voltage
|
||||
output pan_en, // analog supply enable
|
||||
output pdp_en // boost converter enable
|
||||
);
|
||||
|
||||
wire ce_lf = ~module_sel; //高启用,低重置
|
||||
wire ce_hf = module_sel; //高启用,低重置
|
||||
wire ce_lf = ~module_sel; // enable, active high; a low level holds the module in reset
|
||||
wire ce_hf = module_sel; // enable, active high; a low level holds the module in reset
|
||||
//-----------------------------------------GATE-------------------------
|
||||
//门控使能信号同步到输入时钟域,避免亚稳态
|
||||
// Synchronise the gate enable into the input clock domain against metastability
|
||||
reg gate_en_sync1, gate_en_sync2;
|
||||
always @(posedge ck_1356meg) begin
|
||||
gate_en_sync1 <= gate_en;
|
||||
gate_en_sync2 <= gate_en_sync1;
|
||||
end
|
||||
|
||||
assign clk_gate = ~gate_en_sync2;//这里取反是因为外部门控是低有效的
|
||||
assign clk_gate = ~gate_en_sync2; // inverted, the external gate is active low
|
||||
//-----------------------------------------PWM--------------------------
|
||||
|
||||
// CLKOUT is 200 MHz: 4096 steps at 5 ns keep the resolution, at a 20.48 us
|
||||
// period. 400 MHz does not close the 12 bit carry chain at 2.5 ns.
|
||||
Gowin_rPLL pwr_pwm_pll(
|
||||
.clkout(pwr_pwm_pll_clko), //output clkout
|
||||
.clkin(ck_1356meg) //input clkin
|
||||
);
|
||||
|
||||
wire [11:0] pwm_duty_lf; // LF 模块的 PWM 占空比输出
|
||||
wire [11:0] pwm_duty_hf; // HF 模块的 PWM 占空比输出
|
||||
wire [11:0] pwm_duty_lf; // PWM duty from the LF module
|
||||
wire [11:0] pwm_duty_hf; // PWM duty from the HF module
|
||||
|
||||
wire [11:0] pwm_duty; // PWM占空比,实际上是高电平长度,和4096做比例
|
||||
wire [11:0] pwm_duty; // low-level count of the 4096-step PWM period
|
||||
reg [11:0] pwm_cnt= 12'h0;
|
||||
|
||||
always @(posedge pwr_pwm_pll_clko) pwm_cnt <= pwm_cnt + 1'b1; //计数器
|
||||
assign pwr_pwm = (pwm_cnt > pwm_duty); //pwm输出
|
||||
// pwm_duty is from the SPI clock domain; resample it into the PWM domain
|
||||
// so a duty update is never sampled mid transition.
|
||||
reg [11:0] pwm_duty_meta, pwm_duty_sync;
|
||||
always @(posedge pwr_pwm_pll_clko) begin
|
||||
pwm_duty_meta <= pwm_duty;
|
||||
pwm_duty_sync <= pwm_duty_meta;
|
||||
end
|
||||
|
||||
// Register the output; the bare comparator glitches on every count edge.
|
||||
reg pwr_pwm_r;
|
||||
always @(posedge pwr_pwm_pll_clko) begin
|
||||
pwm_cnt <= pwm_cnt + 1'b1; // counter
|
||||
pwr_pwm_r <= (pwm_cnt > pwm_duty_sync); // PWM output
|
||||
end
|
||||
assign pwr_pwm = pwr_pwm_r;
|
||||
|
||||
assign pan_en = 1'b1;
|
||||
assign pdp_en = 1'b1;
|
||||
|
||||
assign pwr_hi = 1'bZ; //使用外部门控时禁用PWRHI,由于是并联的,需要高阻
|
||||
assign pwr_hi = 1'bZ; // PWRHI is replaced by the external gate; the two are wired in parallel, so float it
|
||||
assign dbgled = 1'b1;
|
||||
assign dbg2 = 1'bZ; // 未使用
|
||||
assign dbg2 = 1'bZ; // not used
|
||||
|
||||
fpga_lf uut_lf (
|
||||
.pck0(pck0),
|
||||
|
||||
@@ -7,5 +7,6 @@ create_clock -name CLK_SPI -period 250 -waveform {0 125} [get_ports {spi_sck}]
|
||||
create_clock -name CLK_NCS -period 1000 -waveform {0 500} [get_ports {spi_ncs}]
|
||||
create_clock -name clk24 -period 41.667 -waveform {0 20.834} [get_ports {pck0}]
|
||||
create_clock -name clk1356 -period 73.746 -waveform {0 36.873} [get_ports {ck_1356meg}]
|
||||
create_clock -name pwr_pwm_clk -period 5 [get_nets {pwr_pwm_pll_clko}]
|
||||
set_clock_groups -asynchronous -group [get_clocks {clk1356}] -group [get_clocks {clk24}] -group [get_clocks {CLK_SPI}] -group [get_clocks {CLK_NCS}]
|
||||
report_timing -setup -from_clock [get_clocks {clk1356}] -to [get_ports {pwr_hi}]
|
||||
@@ -47,11 +47,11 @@ rPLL rpll_inst (
|
||||
|
||||
defparam rpll_inst.FCLKIN = "13.56";
|
||||
defparam rpll_inst.DYN_IDIV_SEL = "false";
|
||||
defparam rpll_inst.IDIV_SEL = 1;
|
||||
defparam rpll_inst.IDIV_SEL = 3;
|
||||
defparam rpll_inst.DYN_FBDIV_SEL = "false";
|
||||
defparam rpll_inst.FBDIV_SEL = 58;
|
||||
defparam rpll_inst.DYN_ODIV_SEL = "false";
|
||||
defparam rpll_inst.ODIV_SEL = 2;
|
||||
defparam rpll_inst.ODIV_SEL = 4;
|
||||
defparam rpll_inst.PSDA_SEL = "0000";
|
||||
defparam rpll_inst.DYN_DA_EN = "false";
|
||||
defparam rpll_inst.DUTYDA_SEL = "1000";
|
||||
|
||||
Reference in new issue
Block a user