Updated Configuration Variables (CV) List (markdown)

Gabriel Koppenstein committed 2022-08-02 16:25:16 +02:00
1 parent 8c70460a97
commit 7f0a962633
1 file changed
+53
+53
@@ -53,10 +53,63 @@ Bit0 is used to reverse direction i.e. "0" = normal, "1" = reverse.
Bit5 switches between basic and extended addressing modes i.e. "0" = basic address, "1" = extended address. Bit5 switches between basic and extended addressing modes i.e. "0" = basic address, "1" = extended address.
The other 6 bits are currently not in use and therefore irrelevant. The other 6 bits are currently not in use and therefore irrelevant.
#### CV_31 & CV_32 - Extended CV pointer (Read-Only)
Not in use.
#### CV_47 - Feed-forward gain k_ff
k_ff defines the correction behavior with regard to the y2 variable. High values for k_ff lead to a faster change in the variable. Values for k_ff that are too high can lead to oscillations.
k_ff = CV_47/10000
#### CV_48 - Filter time constant (tau) in ms
The time constant tau characterizes the low-pass filter which is connected downstream in the D component of the PID controller
#### CV_49 - PID Control sampling time t in ms
Every t seconds the pid_control() function gets called to compute the new control output
#### CV_50 - PID Control I Factor
Integral gain factor of the PID-Controller
#### CV_51 - PID Control D Factor
Derivative gain factor of the PID-Controller
#### CV_52 & CV_53 - PID Integral Limits
Maximum and minimum integral part values
#### CV_54 & CV_55 - Gain scheduling config k_p @ x0
CV_54 - High Byte -- CV_55 - Low Byte
#### CV_56 & CV_57 - Gain scheduling config k_p @ x1
CV_56 - High Byte -- CV_57 - Low Byte
#### CV_58 & CV_59 - Gain scheduling config k_p @ x2
CV_58 - High Byte -- CV_59 - Low Byte
#### CV_60 - Gain scheduling config x1 shift percentage
Determines position of x1 in percent -> x1 shift in % ≙ CV_60/255
#### CV_61 - Measurement Iterations
Total amount of BEMF-Voltage measurement iterations
#### CV_62 - Measurement Delay
BEMF-Voltage measurement delay
#### CV_63 & CV_64 - Measurement array cutoffs
CV_63 determines how many elements from the left side (beginning with index 0) of the array will be discarded while CV_64 determines how many elements from the right side (beginning from highest index) will be discarded.
#### CV_65 - New flash variable #### CV_65 - New flash variable
Each Byte of the factory new flash chip should have a inital state of "0xFF". This will be checked for in the beginning of core0.c (see cv_setup_check()). When CV_65 == "255" == "0xFF" the default config (CV.h) will be written to flash. Alternatively a reset to default can be done by either writing "8" to CV_8 or writing "255" to CV_65 which then triggers a reset on restart. Each Byte of the factory new flash chip should have a inital state of "0xFF". This will be checked for in the beginning of core0.c (see cv_setup_check()). When CV_65 == "255" == "0xFF" the default config (CV.h) will be written to flash. Alternatively a reset to default can be done by either writing "8" to CV_8 or writing "255" to CV_65 which then triggers a reset on restart.
#### CV_112, CV_113, CV_114, CV_115 - GPIO PWM Configuration
PWM enabled "1" - PWM disabled "0"
#### CV_116 to CV_171 - PWM Slice configuration
Every slice controls two outputs (Two independent output channels, duty cycle from 0% to 100% inclusive) and can be configured with several parameters:
* Wrap (16Bit): Sets the slice time period of x cycles - effectively deciding the frequency
* Clock Divider: Additional clock divider
* Level Channel A/Channel B (16Bit): Determining how many of the x cycles the signal is at a high level - effectively deciding the duty cycle
A more detailed explanation can be found in the [RP2040-Datasheet](https://datasheets.raspberrypi.com/rp2040/rp2040-datasheet.pdf) in Chapter 4.5.
#### CV_175 - speed_helper timer delay #### CV_175 - speed_helper timer delay
This timer delay can be used to change the time between two speed steps. So basically an additional option to adjust the deceleration and acceleration rate. This timer delay can be used to change the time between two speed steps. So basically an additional option to adjust the deceleration and acceleration rate.