Updated Configuration Variables (CV) List (markdown)
1 parent
8c70460a97
commit
7f0a962633
1 file changed
+54
-1
@@ -53,10 +53,63 @@ Bit0 is used to reverse direction i.e. "0" = normal, "1" = reverse.
|
||||
Bit5 switches between basic and extended addressing modes i.e. "0" = basic address, "1" = extended address.
|
||||
The other 6 bits are currently not in use and therefore irrelevant.
|
||||
|
||||
|
||||
#### CV_31 & CV_32 - Extended CV pointer (Read-Only)
|
||||
Not in use.
|
||||
|
||||
#### CV_47 - Feed-forward gain k_ff
|
||||
k_ff defines the correction behavior with regard to the y2 variable. High values for k_ff lead to a faster change in the variable. Values for k_ff that are too high can lead to oscillations.
|
||||
k_ff = CV_47/10000
|
||||
|
||||
#### CV_48 - Filter time constant (tau) in ms
|
||||
The time constant tau characterizes the low-pass filter which is connected downstream in the D component of the PID controller
|
||||
|
||||
#### CV_49 - PID Control sampling time t in ms
|
||||
Every t seconds the pid_control() function gets called to compute the new control output
|
||||
|
||||
#### CV_50 - PID Control I Factor
|
||||
Integral gain factor of the PID-Controller
|
||||
|
||||
#### CV_51 - PID Control D Factor
|
||||
Derivative gain factor of the PID-Controller
|
||||
|
||||
#### CV_52 & CV_53 - PID Integral Limits
|
||||
Maximum and minimum integral part values
|
||||
|
||||
#### CV_54 & CV_55 - Gain scheduling config k_p @ x0
|
||||
CV_54 - High Byte -- CV_55 - Low Byte
|
||||
|
||||
#### CV_56 & CV_57 - Gain scheduling config k_p @ x1
|
||||
CV_56 - High Byte -- CV_57 - Low Byte
|
||||
|
||||
#### CV_58 & CV_59 - Gain scheduling config k_p @ x2
|
||||
CV_58 - High Byte -- CV_59 - Low Byte
|
||||
|
||||
#### CV_60 - Gain scheduling config x1 shift percentage
|
||||
Determines position of x1 in percent -> x1 shift in % ≙ CV_60/255
|
||||
|
||||
#### CV_61 - Measurement Iterations
|
||||
Total amount of BEMF-Voltage measurement iterations
|
||||
|
||||
#### CV_62 - Measurement Delay
|
||||
BEMF-Voltage measurement delay
|
||||
|
||||
#### CV_63 & CV_64 - Measurement array cutoffs
|
||||
CV_63 determines how many elements from the left side (beginning with index 0) of the array will be discarded while CV_64 determines how many elements from the right side (beginning from highest index) will be discarded.
|
||||
|
||||
#### CV_65 - New flash variable
|
||||
Each Byte of the factory new flash chip should have a inital state of "0xFF". This will be checked for in the beginning of core0.c (see cv_setup_check()). When CV_65 == "255" == "0xFF" the default config (CV.h) will be written to flash. Alternatively a reset to default can be done by either writing "8" to CV_8 or writing "255" to CV_65 which then triggers a reset on restart.
|
||||
|
||||
#### CV_112, CV_113, CV_114, CV_115 - GPIO PWM Configuration
|
||||
PWM enabled "1" - PWM disabled "0"
|
||||
|
||||
#### CV_116 to CV_171 - PWM Slice configuration
|
||||
Every slice controls two outputs (Two independent output channels, duty cycle from 0% to 100% inclusive) and can be configured with several parameters:
|
||||
|
||||
* Wrap (16Bit): Sets the slice time period of x cycles - effectively deciding the frequency
|
||||
* Clock Divider: Additional clock divider
|
||||
* Level Channel A/Channel B (16Bit): Determining how many of the x cycles the signal is at a high level - effectively deciding the duty cycle
|
||||
|
||||
A more detailed explanation can be found in the [RP2040-Datasheet](https://datasheets.raspberrypi.com/rp2040/rp2040-datasheet.pdf) in Chapter 4.5.
|
||||
|
||||
#### CV_175 - speed_helper timer delay
|
||||
This timer delay can be used to change the time between two speed steps. So basically an additional option to adjust the deceleration and acceleration rate.
|
||||
Reference in new issue
Block a user