New "Pico setup for Windows" Repository, add Link to prebuilt "picoprobe.uf2" in Github repo
1 parent
fe17af64b7
commit
7995c845fc
1 file changed
+7
-6
+7
-6
@@ -16,17 +16,18 @@ To build the software and run it on the Controller we need to interface the RP20
|
|||||||
|
|
||||||
### Windows
|
### Windows
|
||||||
|
|
||||||
1. Download and install [Pico setup for Windows from ndabas](https://github.com/ndabas/pico-setup-windows) and make sure to check the box for also installing Zadig.
|
1. Download and install [Pico setup for Windows](https://github.com/raspberrypi/pico-setup-windows) and make sure to check the box for also installing Zadig.
|
||||||
2. Clone and build Pico repos either by checking the box at the end of the setup.
|
2. Clone and build Pico repos either by checking the box at the end of the setup.
|
||||||
3. Connect Raspberry Pi Pico via USB while holding the reset button. Your Pi Pico should now be visible in Windows explorer as a mass storage device.
|
3. Connect Raspberry Pi Pico via USB while holding the reset button. Your Pi Pico should now be visible in Windows explorer as a mass storage device.
|
||||||
4. Navigate to the picoprobe/build subfolder in your installation folder and copy picoprobe.uf2 to your Pi Pico. Alternatively, download the picoprobe.uf2 file from [here](https://www.raspberrypi.com/documentation/microcontrollers/raspberry-pi-pico.html#debugging-using-another-raspberry-pi-pico).The Pi Pico onboard LED should now be on.
|
4. Download the latest prebuilt "picoprobe.uf2" release binary from [here](https://github.com/raspberrypi/pico-setup-windows) or download it from the [Raspberry Pi Website](https://www.raspberrypi.com/documentation/microcontrollers/raspberry-pi-pico.html#debugging-using-another-raspberry-pi-pico). Alternatively, you can get the file by navigating to the picoprobe/build subfolder.
|
||||||
5. Navigate to the tools subfolder in your installation folder and open zadig.exe
|
5. Copy "picoprobe.uf2" to your Pi Pico. The Pi Pico onboard LED should now light up.
|
||||||
6. Install the picoprobe driver using zadig.exe as shown in [Getting started with Raspberry Pi Pico - Appendix A - Page 62](https://datasheets.raspberrypi.com/pico/getting-started-with-pico.pdf#%5B%7B%22num%22%3A65%2C%22gen%22%3A0%7D%2C%7B%22name%22%3A%22XYZ%22%7D%2C115%2C692.106%2Cnull%5D)
|
6. Navigate to the tools subfolder in your installation folder and open zadig.exe
|
||||||
7. Connect GND to GND, VBUS to +V, GPIO2 to SWCLK, GPIO3 to SWDIO as shown in the picture below.
|
7. Install the picoprobe driver using "zadig.exe" as shown in [Getting started with Raspberry Pi Pico - Appendix A - Page 62](https://datasheets.raspberrypi.com/pico/getting-started-with-pico.pdf#%5B%7B%22num%22%3A65%2C%22gen%22%3A0%7D%2C%7B%22name%22%3A%22XYZ%22%7D%2C115%2C692.106%2Cnull%5D)
|
||||||
|
8. Connect GND to GND, VBUS to +V, GPIO2 to SWCLK, GPIO3 to SWDIO as shown in the picture below.
|
||||||
|
|
||||||
<img src="https://github.com/gab-k/RP2040-Decoder/blob/main/docs/svg/Debug_Connections.svg" width="700"/>
|
<img src="https://github.com/gab-k/RP2040-Decoder/blob/main/docs/svg/Debug_Connections.svg" width="700"/>
|
||||||
|
|
||||||
8. To finally build and flash, open the Developer Command Prompt for Pico and type the following commands:
|
9. To finally build and flash, open the Developer Command Prompt for Pico and type the following commands:
|
||||||
* git clone https://github.com/gab-k/RP2040-Decoder.git
|
* git clone https://github.com/gab-k/RP2040-Decoder.git
|
||||||
* cd RP2040-Decoder
|
* cd RP2040-Decoder
|
||||||
* mkdir build
|
* mkdir build
|
||||||
|
|||||||
Reference in new issue
Block a user