update svg

Gabriel Koppenstein committed 2022-08-01 21:50:23 +02:00
1 parent 4903cca6d0
commit 5b1cd54e7d
1 file changed
+9 -5
+9 -5
@@ -42,7 +42,7 @@ Input Stage
D1 Rectifies the DCC square-wave into +V, the amplitude is not critical as long as its within the 25V limit. The rectified voltage +V is then provided to the 3.3V voltage regulator (U1) and to the motor driver (U2).
The MOSFET on the right effectively translates the rather high DCC voltage to a suitable level for the microcontroller to process. When Q1 is turned off GPIO24 is pulled high by the RP2040, as soon as Q1 gets turned on (V<sub>GS</sub> > V<sub>GS,th</sub>), GPIO24 gets pulled to GND potential. R1 and R2 ensure that V<sub>GS</sub> doesnt exceed ±20V.
The MOSFET on the right effectively translates the rather high DCC voltage to a suitable level for the microcontroller to process. When Q1 is turned off GPIO21 is pulled high by the RP2040 internal pull-up resistor, as soon as Q1 gets turned on (V<sub>GS</sub> > V<sub>GS,th</sub>), GPIO21 gets pulled to GND potential. R1 and R2 ensure that V<sub>GS</sub> doesnt exceed ±20V.
Motor Driver
--------------------------
@@ -56,21 +56,23 @@ Auxillary Output
--------------------------
![Auxillary Output](https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/Aux_Outputs.svg)
Switching of loads up to a maximum of about ~400mA can be done using four N-Channel MOSFETS. They are switching on the low-side which means the load effectively gets connected to GND potential as the Transistor starts to conduct.
Switching of loads up to a maximum of about ~400mA can be done using four N-Channel MOSFETS. They are switching on the low-side which means the load effectively gets connected to GND potential as the transistor starts to conduct. GPIO24 - GPIO27 are used.
GPIO
--------------------------
To Switch lighter loads, six GPIOs can be used. Alternatively they can of course be used as inputs as well (e.g. Reed switch).
To switch lighter loads six soldering pads on the back side of the PCB are connected to GPIO0 - GPIO5 pins . Although not implemented yet they could theoretically be used as inputs as well (e.g. Reed switch).
Microcontroller
--------------------------
![Microcontroller](https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/Microcontroller.svg)
The Microcontroller needs a crystal oscillator to function properly. Flash memory is also needed as it holds the configuration variables and the program itself. R3 & C14 are used to filter ADC_AVDD (This might possibly be omitted in a future Revision).
The Microcontroller needs a crystal oscillator to function properly. External flash memory is also needed as it holds the configuration variables and the program itself. R3 & C14 are used to filter ADC_AVDD (ADC Reference Voltage).
Complete Schematic
--------------------------
![Auxillary Output](https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/RP2040-Decoder-Rev_0_2.svg)
![Complete schematic](https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/RP2040-Decoder.svg)
BOM & Alternative Parts
--------------------------
@@ -91,6 +93,8 @@ BOM & Alternative Parts
| U4 | 1 | / | Raspberry Pi RP2040 Microcontroller | RP2040 | QFN-56-1EP_7x7mm_P0.4mm |
| Y1 | 1 | f = 12MHz | Crystal Oscillator | X322512MSB4SI | Crystal_SMD_3225-4Pin_3.2x2.5mm |
NOTE: Keep capacitor V<sub>max</sub> in mind!
Alternatives for BDR6133:
[PT5126A-S-TP](https://lcsc.com/product-detail/Motor-Driver-ICs_PTC-Princeton-Tech-PT5126A-S-TP_C162093.html)