Files
RP2040-Decoder/core1.c
T
1nct c8eece795f - Added and updated svg files used in docs
- minor change in speed_table calculation
2022-08-01 21:28:06 +02:00

315 lines
12 KiB
C

//////////////////////////
// RP2040-Decoder //
// Gabriel Koppenstein //
// core1.c //
//////////////////////////
#include "core1.h"
struct repeating_timer pid_control_timer,speed_helper_timer;
// Update speed_step_target, end_target_index and direction on receiving data from core0
void update_speed_dir(pid_params *pid, uint32_t speed_step_target){
pid->speed_step_target = speed_step_target;
// When CV_29 Bit 0 is set direction is reversed
bool reverse_dir = CV_ARRAY_FLASH[28] & 0b00000001;
// Forward
if(speed_step_target > 127) {
pid->direction = true^reverse_dir;
if (pid->speed_step_target == 128) pid->end_target_index = 0;
else pid->end_target_index = (pid->speed_step_target-129);
}
// Reverse
else {
pid->direction = false^reverse_dir;
if (pid->speed_step_target == 0) pid->end_target_index = 0;
else pid->end_target_index = (pid->speed_step_target-1);
}
}
// This function gets called every x milliseconds where x is CV_175.
// The purpose of this function is to implement a time delay in acceleration or deceleration
bool speed_helper(struct repeating_timer *t) {
// pid->setpoint only gets adjusted when the speed_helper_counter is equal to the accel_rate/decel_rate
// -> Time for 1 Speed Step := (speed_helper timer delay)*(accel_rate) or CV_175*CV_3 or CV_175*CV_4
pid_params *pid = (pid_params *)(t->user_data);
uint8_t accel_rate = CV_ARRAY_FLASH[2];
uint8_t decel_rate = CV_ARRAY_FLASH[3];
static uint8_t speed_helper_counter;
static uint8_t speed_table_index;
// Emergency Stop
if (pid->speed_step_target == 129 || pid->speed_step_target==1) {
speed_table_index = 0;
speed_helper_counter = 0;
pid->setpoint = pid->speed_table[speed_table_index];
}
// Acceleration
else if (pid->end_target_index > speed_table_index && speed_helper_counter == accel_rate) {
if(!accel_rate) speed_table_index = pid->end_target_index; // directly accelerate to end target speed
else speed_table_index++;
pid->setpoint = pid->speed_table[speed_table_index];
speed_helper_counter = 0;
}
// Deceleration
else if (pid->end_target_index < speed_table_index && speed_helper_counter == decel_rate) {
if(!decel_rate) speed_table_index = pid->end_target_index; // directly decelerate to end target speed
else speed_table_index--;
pid->setpoint = pid->speed_table[speed_table_index];
speed_helper_counter = 0;
}
// Acceleration/Deceleration "scheduled"
else if (pid->end_target_index != speed_table_index) speed_helper_counter++;
// Target reached -> Reset Counter
else speed_helper_counter = 0;
// return true to schedule the repeating timer again
return true;
}
// Helper function to adjust pwm level/duty cycle.
void adjust_pwm_level(uint16_t level, pid_params *pid) {
if (pid->direction) {
pwm_set_gpio_level(MOTOR_REV_PIN, 0);
pwm_set_gpio_level(MOTOR_FWD_PIN, level);
}
//Reverse
else {
pwm_set_gpio_level(MOTOR_FWD_PIN, 0);
pwm_set_gpio_level(MOTOR_REV_PIN, level);
}
}
// Update feed-forward slope/gradient for both directions
void update_m(pid_params *pid){
pid->m_fwd = (pid->y_2_fwd-pid->y_1_fwd)/(pid->x_2_fwd-pid->x_1_fwd);
pid->m_rev = (pid->y_2_rev-pid->y_1_rev)/(pid->x_2_rev-pid->x_1_rev);
}
// Update feedforward function value y_2 in both directions
void update_y(pid_params *pid,float i){
// Forward
if(pid->direction) {
pid->y_2_fwd += i*pid->k_ff;
// Limit y_2_fwd
if(pid->y_2_fwd > pid->max_output) pid->y_2_fwd = pid->max_output;
else if(pid->y_2_fwd < pid->y_1_fwd) pid->y_2_fwd = pid->y_1_fwd;
}
// Reverse
else{
pid->y_2_rev += i*pid->k_ff;
// Limit y_2_rev
if(pid->y_2_rev > pid->max_output) pid->y_2_rev = pid->max_output;
else if(pid->y_2_rev < pid->y_1_rev) pid->y_2_rev = pid->y_1_rev;
}
update_m(pid);
}
// Returns feedforward value corresponding to current setpoint
float get_ff_val(pid_params *pid){
float val;
// Forward
if(pid->direction){
val = pid->m_fwd*((float)pid->setpoint-pid->x_1_fwd)+pid->y_1_fwd;
}
// Reverse
else{
val = pid->m_rev*((float)pid->setpoint-pid->x_1_rev)+pid->y_1_rev;
}
return val;
}
// Returns proportional gain value corresponding to current setpoint
float get_kp(pid_params *pid){
float sp = (float)pid->setpoint;
if (sp < pid->k_p_x_1){
return pid->k_p_m_1 * sp + pid->k_p_y_0;
}
else{
return pid->k_p_m_2 * (sp - pid->k_p_x_1) + pid->k_p_y_1;
}
}
// PID controller function gets called every x milliseconds where x is CV_49 aka sampling time (pid->t)
bool pid_control(struct repeating_timer *t){
// Cast (void *) to (pid_params *)
pid_params *pid = (pid_params *)(t->user_data);
// Acceleration from standstill or change in direction -> reset previous derivative, error and integral parts
if((!pid->setpoint_prev && !pid->setpoint) || (pid->direction != pid->direction_prev)){
pid->d_prev = 0.0f;
pid->i_prev = 0.0f;
pid->e_prev = 0.0f;
}
// Get feed-forward and proportional gain values
float feed_fwd = get_ff_val(pid);
pid->k_p = get_kp(pid);
// Measure BEMF voltage and compute error
pid->measurement = measure(pid->msr_total_iterations,
pid->msr_total_iterations,
pid->l_side_arr_cutoff,
pid->r_side_arr_cutoff,
pid->direction);
float e = (float)pid->setpoint - (pid->measurement - pid->adc_offset);
// Proportional part, integral part and derivative part (including digital low-pass-filter with time constant tau)
float p = pid->k_p * e;
float i = pid->ci_0*(e + pid->e_prev) + pid->i_prev;
float d = pid->cd_0*(pid->measurement-pid->measurement_prev)+pid->cd_1*pid->d_prev;
// Check for limits on the integral part
if (i > pid->int_lim_max)i = pid->int_lim_max;
else if (i < pid->int_lim_min)i = pid->int_lim_min;
// Sum feed forward + all controller terms (p+i+d). Limit Output from 0% to 100% duty cycle
float output = feed_fwd+p+i+d;
if (output < 0 || !pid->setpoint) output = 0.0f;
else if (output > pid->max_output) output = pid->max_output;
// Set PWM Level and discard results in adc fifo
adjust_pwm_level((uint16_t)roundf(output),pid);
adc_fifo_drain();
if(pid->setpoint > 2) {
printf("p:%f\n", p);
printf("i:%f\n", i);
printf("d:%f\n", d);
printf("o:%f\n", output);
}
// Check for High or Low Integrator values -> Update x,y values of feedforward function
if( (output < pid->max_output && output > pid->max_output/2) && ((i > pid->int_lim_max/2) || (i < pid->int_lim_min/2)) ) update_y(pid,i);
// Save previous error, integrator, differentiator, direction, setpoint and measured value also sum error to e_sum
pid->e_prev = e;
pid->i_prev = i;
pid->d_prev = d;
pid->direction_prev = pid->direction;
pid->setpoint_prev = pid->setpoint;
pid->measurement_prev = pid->measurement;
// return true to schedule the repeating timer again
return true;
}
// PID controller and measurement parameter, and speed_table initialization
void init_pid(pid_params *pid){
// Measurement variables initialization
pid->adc_offset = (float)CV_ARRAY_FLASH[171];
pid->msr_total_iterations = CV_ARRAY_FLASH[60];
pid->msr_delay_in_us = CV_ARRAY_FLASH[61];
pid->l_side_arr_cutoff = CV_ARRAY_FLASH[62];
pid->r_side_arr_cutoff = CV_ARRAY_FLASH[63];
// Speed table initialization
// Calculate speed setpoint table according to V_min, V_max and V_mid CVs
double v_min = (double)CV_ARRAY_FLASH[1];
double v_mid = (double)CV_ARRAY_FLASH[5]*16;
double v_max = (double)CV_ARRAY_FLASH[4]*16;
double delta_x = 63;
double m_1 = (v_mid-v_min)/delta_x;
double m_2 = (v_max-v_mid)/delta_x;
pid->speed_table[0] = 0;
for (uint8_t i = 1; i < 64; ++i) {
pid->speed_table[i] = (uint16_t)lround(m_1*(i-1)+v_min);
}
for (uint8_t i = 64; i < 127; ++i) {
pid->speed_table[i] = (uint16_t)lround(m_2*(i-63)+v_mid);
}
// Controller constants initialization
pid->k_i = (float)CV_ARRAY_FLASH[49]/10;
pid->k_d = (float)CV_ARRAY_FLASH[50]/10000;
pid->tau = (float)CV_ARRAY_FLASH[47]/1000;
pid->t = (float)CV_ARRAY_FLASH[48]/1000;
pid->ci_0 = (pid->k_i*pid->t)/2;
pid->cd_0 = -(2*pid->k_d)/(2*pid->tau+pid->t);
pid->cd_1 = (2*pid->tau-pid->t)/(2*pid->tau+pid->t);
pid->int_lim_max = 10*(float)CV_ARRAY_FLASH[51];
pid->int_lim_min = -10*(float)CV_ARRAY_FLASH[52];
pid->k_ff = (float)CV_ARRAY_FLASH[46]/10000; // 0.005f;
pid->max_output = (float)(_125M/(CV_ARRAY_FLASH[8]*100+10000));
pid->x_1_rev = 0.0f;
pid->x_1_fwd = 0.0f;
pid->y_1_fwd = (float)get_16bit_CV(175); //(float)measure_base_pwm(pid,1);
pid->y_1_rev = (float)get_16bit_CV(177); //(float)measure_base_pwm(pid,0);
pid->x_2_rev = (float)pid->speed_table[126];
pid->x_2_fwd = (float)pid->speed_table[126];
// Controller variables initialization
pid->y_2_fwd = pid->max_output;
pid->y_2_rev = pid->max_output;
pid->measurement = 0.0f;
pid->measurement_prev = 0.0f;
pid->e_prev = 0.0f;
pid->i_prev = 0.0f;
pid->d_prev = 0.0f;
pid->direction = false;
pid->direction_prev = false;
pid->speed_step_target = 0;
pid->setpoint = 0;
// Gain scheduling initialization
pid->k_p_x_1_shift = (float)CV_ARRAY_FLASH[59] / 255.0f;
pid->k_p_x_1 = (float)pid->speed_table[126] * pid->k_p_x_1_shift;
pid->k_p_x_2 = (float)pid->speed_table[126] * (1.0f - pid->k_p_x_1_shift);
pid->k_p_y_0 = (float)get_16bit_CV(53) / 100.0f;
pid->k_p_y_1 = (float)get_16bit_CV(55) / 100.0f;
pid->k_p_y_2 = (float)get_16bit_CV(57) / 100.0f;
pid->k_p_m_1 = (pid->k_p_y_1 - pid->k_p_y_0) / pid->k_p_x_1;
pid->k_p_m_2 = (pid->k_p_y_2 - pid->k_p_y_1) / pid->k_p_x_2;
update_m(pid);
}
void core1_entry() {
printf("core1 init...\n");
pid_params pid_parameters;
pid_params *pid = &pid_parameters;
init_pid(pid);
alarm_pool_add_repeating_timer_ms(alarm_pool_create(0,1),
CV_ARRAY_FLASH[48],
pid_control,
pid,
&pid_control_timer);
irq_set_priority(0,0x00); // 0x00 = highest priority
alarm_pool_add_repeating_timer_ms(alarm_pool_create(1,1),
CV_ARRAY_FLASH[174],
speed_helper,
pid,
&speed_helper_timer);
// Send direction pointer for access and to let core0 know that core1 is done with initialization,
// Note: Pointer will be cast into uint32_t and then back into bool * on core0 (Both 32-Bit Datatype).
// This is done only to accommodate the correct data type associated with multicore_fifo_push_blocking().
multicore_fifo_push_blocking((uint32_t) &(pid->direction));
uint64_t packet_timeout_threshold_in_us = CV_ARRAY_FLASH[10]*1000000;
absolute_time_t time_last_update = get_absolute_time();
printf("core1 done\n");
while (1){
// Check for time difference between last packet and current time (Packet Timeout)
absolute_time_t current_time = get_absolute_time();
if (absolute_time_diff_us(time_last_update,current_time) > packet_timeout_threshold_in_us){
update_speed_dir(pid,0);
}
// If core0 sends new speed data to core1 speed_step_target and direction variables get updated
if(multicore_fifo_rvalid()) {
update_speed_dir(pid, multicore_fifo_pop_blocking());
time_last_update = get_absolute_time();
}
}
}