Files
RP2040-Decoder/docs/sphinx/source/hardware/hw_description_md.md
T
2024-11-27 21:59:54 +01:00

109 lines
5.7 KiB
Markdown

# Hardware Description
## Overview
![Block Diagram](https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/Block_Diagram.svg)
The above block diagram gives a general overview regarding the operation of components. For better illustration it has been divided into four functional blocks. Furthermore these functional blocks can be subdivided and will be explained below.
* Input Stage
- DCC Signal Level Shift
- Bridge Rectifier & Voltage Regulator
* Motor Driver
- Motor Driver
- Back EMF measurement (ADC)
* General Purpose
- GPIO
- Auxillary output
* Microcontroller
- Flash memory
- Crystal oscillator
## Characteristics
| Parameter | Symbol | Minimum | Maximum | Unit |
| ----------------------------------------------------- | -------------- | ------- | -------- | ---- |
| Absolute max. DCC Input Voltage | V<sub>DCC</sub> | -25 | +25 | V |
| Absolute max. GPIO Voltage<sup>(0)</sup> | V<sub>PIN</sub> | -0.5 | 3.3+0.5 | V |
| Input Voltage High<sup>(0)</sup> | V<sub>IH</sub> | 2.145 | 3.6 | V |
| Input Voltage Low<sup>(0)</sup> | V<sub>IL</sub> | 0 | 1.155 | V |
| Total GPIO Current<sup>(0)</sup> | I<sub>IOVDD_MAX</sub>| | 50 | mA |
| Absolute max. motor output current<sup>(1)</sup> | I<sub>MOTOR</sub> | | 2.8 | A |
| Absolute max. auxillary output current<sup>(2)</sup> | I<sub>AUX</sub> | | 400 | mA |
(0): According to: [RP2040 Datasheet](https://datasheets.raspberrypi.com/rp2040/rp2040-datasheet.pdf) (assuming V<sub>DD</sub> = 3.3V)
(1): According to: [BDR6133 Datasheet](https://datasheet.lcsc.com/lcsc/2101211904_Bardeen-Micro--BDR6133_C2687793.pdf)
(2): According to: [T2N7002BK Datasheet](https://datasheet.lcsc.com/lcsc/1810271831_TOSHIBA-T2N7002BK-LM_C146372.pdf)
## Input Stage
![Input Stage](https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/Input_Stage.svg)
D1 Rectifies the DCC square-wave into +V, the amplitude is not critical as long as its within the 25V limit. The rectified voltage +V is then provided to the 3.3V voltage regulator (U1) and to the motor driver (U2).
The MOSFET on the right effectively translates the rather high DCC voltage to a suitable level for the microcontroller to process. When Q1 is turned off GPIO21 is pulled high by the RP2040 internal pull-up resistor, as soon as Q1 gets turned on (V<sub>GS</sub> > V<sub>GS,th</sub>), GPIO21 gets pulled to GND potential. R1 and R2 ensure that V<sub>GS</sub> doesnt exceed ±20V.
## Motor Driver
![Motor Driver](https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/Motor_Driver.svg)
The Motor Driver is a complete H-Bridge IC specifically made for DC-Motors.
In order to control the motor, it is necessary to measure the back-EMF. This is done by the ADC which measures at Points ADC_EMF_A and ADC_EMF_B respectively. The two resistors are used as a voltage divider.
## Auxillary Output
![Auxillary Output](https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/Aux_Outputs.svg)
Switching of loads up to a maximum of about ~400mA can be done using four N-Channel MOSFETS. They are switching on the low-side which means the load effectively gets connected to GND potential as the transistor starts to conduct. GPIO24 - GPIO27 are used.
## GPIO
To switch lighter loads six soldering pads on the back side of the PCB are connected to GPIO0 - GPIO5 pins . Although not implemented yet they could theoretically be used as inputs as well (e.g. Reed switch).
## Microcontroller
![Microcontroller](https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/Microcontroller.svg)
The Microcontroller needs a crystal oscillator to function properly. External flash memory is also needed as it holds the configuration variables and the program itself. R3 & C14 are used to filter ADC_AVDD (ADC Reference Voltage).
## Complete Schematic
![Complete schematic](https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/RP2040-Decoder.svg)
BOM & Alternative Parts
--------------------------
| Ref | Quantity | Value | Component Type | Component Name | Footprint |
| ----------------------------------------------------- | -------------- | ------- | -------- | ---- |---- |
| C1, C2, C5, C6, C14 | 5 | 10u | Ceramic Capacitor | / | 0603_1608Metric |
| C3, C4, C7, C8, C9, C10, C11, C12, C13, C15 | 10 | 100n | Ceramic Capacitor | / | 0603_1608Metric |
| C16, C17 | 2 | 33p | Ceramic Capacitor | / | 0603_1608Metric |
| D1 | 1 | V<sub>RMS</sub> = 40V , I<sub>F</sub> = 2A | Bridge Rectifier | KMB24F | MBS (TO-269AA) |
| Q1, Q2, Q3, Q4, Q5 | 5 | V<sub>DS</sub> = 60V , I<sub>D</sub> = 0.4A | N-Channel MOSFET |T2N7002BK | SOT-23 |
| R1, R2, R5, R6 | 4 | 6k8 | Resistor | / | 0603_1608Metric |
| R3 | 1 | 200 | Resistor | / | 0603_1608Metric |
| R7, R8, R9 | 3 | 1k | Resistor | / | 0603_1608Metric |
| U1 | 1 | V<sub>OUT</sub> = 3.3V | Low Dropout Voltage Regulator | HT7533S | SOT-23 |
| U2 | 1 | I = 2.8A | H-Bridge driver | BDR6133 | SOIC-8 |
| U3 | 1 | 64Mb | Serial Flash Memory | W25Q64JVSSIQ | SOIC-8 |
| U4 | 1 | / | Raspberry Pi RP2040 Microcontroller | RP2040 | QFN-56-1EP_7x7mm_P0.4mm |
| Y1 | 1 | f = 12MHz | Crystal Oscillator | X322512MSB4SI | Crystal_SMD_3225-4Pin_3.2x2.5mm |
NOTE: Keep capacitor V<sub>max</sub> in mind!
Alternatives for BDR6133:
[PT5126A-S-TP](https://lcsc.com/product-detail/Motor-Driver-ICs_PTC-Princeton-Tech-PT5126A-S-TP_C162093.html)
[PT2476](https://lcsc.com/product-detail/Motor-Driver-ICs_PTC-Princeton-Tech-PT2476_C481903.html)
Alternative for HT7533S:
[GS7533-33TR3](https://www.lcsc.com/product-detail/Linear-Voltage-Regulators-LDO_Gainsil-GS7533-33TR3_C7427372.html)