Files
RP2040-Decoder/core0.c
T
2023-12-31 22:12:07 +01:00

676 lines
27 KiB
C

//////////////////////////
// RP2040-Decoder //
// Gabriel Koppenstein //
// core0.c //
//////////////////////////
#include "core0.h"
// XIP_BASE + FLASH_TARGET_OFFSET = "0x101FF000" <- This address need to be smaller than __flash_binary_end stored in RP2040-Decoder.elf.map
const uint8_t *CV_ARRAY_FLASH = (const uint8_t *) (XIP_BASE + FLASH_TARGET_OFFSET);
uint64_t input_bit_buffer = 0;
uint16_t level_table[32] = {0};
absolute_time_t falling_edge_time,rising_edge_time;
// Function returns average of values deviating less than twice the standard deviation from original average
float two_std_dev(const float arr[], const uint32_t length){
// Calculate arithmetic average
float sum = 0;
for (uint32_t i = 0; i < length; ++i) {
sum += arr[i];
}
const float x_avg = sum / (float)length;
// Calculate sample variance and sampled standard deviation
sum = 0;
for (uint32_t i = 0; i < length; ++i) {
sum += (arr[i]-x_avg)*(arr[i]-x_avg);
}
const float variance = sum / (float)(length-1);
const float std_dev = sqrtf(variance);
// Sum every element that is within two times the sampled standard deviation and compute new average
sum = 0;
uint32_t counter = 0;
for (uint32_t i = 0; i < length; ++i) {
const float diff = fabsf(arr[i]-x_avg);
if ( diff < std_dev*2.0f ){
sum += arr[i];
counter++;
}
}
return sum / (float)counter;
}
// Measures constant adc offset and programs the offset into flash
void adc_offset_adjustment(uint32_t n){
LOG(1, "adc_offset_adjustment");
float offsets_fwd[n];
float offsets_rev[n];
// Set PWM level to 0 just to be sure
pwm_set_gpio_level(MOTOR_FWD_PIN, 0);
pwm_set_gpio_level(MOTOR_REV_PIN, 0);
busy_wait_ms(1000);
// Measure n times in "reverse direction" (GPIO 28)
adc_select_input(2);
adc_run(true);
for (uint32_t i = 0; i < n; i++) {
offsets_rev[i] = (float)adc_fifo_get_blocking();
}
adc_run(false);
adc_fifo_drain();
busy_wait_ms(1000);
// Measure n times in "forward direction" (GPIO 29)
adc_select_input(3);
adc_run(true);
for (uint32_t i = 0; i < n; i++) {
offsets_fwd[i] = (float)adc_fifo_get_blocking();
}
adc_run(false);
adc_fifo_drain();
// Find overall average discarding outliers in measurement
const float offset_avg_fwd = two_std_dev(offsets_fwd, n);
const float offset_avg_rev = two_std_dev(offsets_rev, n);
const float overall_avg = (offset_avg_fwd+offset_avg_rev)/2;
const uint8_t offset = (uint8_t)roundf(overall_avg);
LOG(1, "new adc offset CV[171] (%f): (uint8_t)%d\n", overall_avg, offset);
// Create temporary array -> change CV 172 in temp array -> erase flash -> write temp array to flash
uint8_t CV_ARRAY_TEMP[CV_ARRAY_SIZE];
memcpy(CV_ARRAY_TEMP, CV_ARRAY_FLASH, sizeof(CV_ARRAY_TEMP));
CV_ARRAY_TEMP[171] = offset;
flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE);
flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_TEMP, FLASH_PAGE_SIZE * 2);
}
// Confirmation after writing or verifying a CV
// Works by creating a spike in current consumption, this is detected by the command station
void acknowledge() {
const uint16_t max_lvl = _125M/(CV_ARRAY_FLASH[8]*100+10000);
pwm_set_gpio_level(MOTOR_FWD_PIN, max_lvl);
busy_wait_ms(3);
pwm_set_gpio_level(MOTOR_FWD_PIN, 0);
pwm_set_gpio_level(MOTOR_REV_PIN, max_lvl);
busy_wait_ms(3);
pwm_set_gpio_level(MOTOR_REV_PIN, 0);
}
// When bit matches sent byte -> acknowledge()
void verify_cv_bit(const uint16_t cv_address,bool bit_val, uint8_t bit_pos) {
const uint8_t mask = 0b00000001;
const bool res = ( (CV_ARRAY_FLASH[cv_address] >> bit_pos) &mask ) == bit_val;
if (res) {
acknowledge();
}
}
// When byte matches sent byte -> acknowledge()
void verify_cv_byte(const uint16_t cv_address, const uint8_t cv_data){
if (CV_ARRAY_FLASH[cv_address] == cv_data) acknowledge();
}
// CV writing function first erases necessary amount of blocks in flash and then rewrites to flash
void regular_cv_write(const uint16_t cv_index, const uint8_t cv_data){
uint8_t CV_ARRAY_TEMP[CV_ARRAY_SIZE];
memcpy(CV_ARRAY_TEMP, CV_ARRAY_FLASH, sizeof(CV_ARRAY_TEMP));
CV_ARRAY_TEMP[cv_index] = cv_data;
flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE);
flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_TEMP, FLASH_PAGE_SIZE * 2);
acknowledge();
}
// There are some exceptions to writing CVs - e.g. writing to a read only CV is not valid - this gets handled here
void write_cv_handler(const uint16_t cv_index, const uint8_t cv_data){
switch (cv_index) {
case 0: //CV_1
// CV_1 => Value = 0 is not allowed
if (cv_data == 0 || cv_data > 127)
break;
regular_cv_write(cv_index,cv_data);
break;
case 6: //CV_7
// Read only (CV_7 - Version no.)
// ADC offset Adjustment (CV_7; Value = 7);
if (cv_data == 7) {
LOG(1, "trigger adc offset adjustment via cv7 => 7\n");
adc_offset_adjustment(8192);
}
break;
case 7: //CV_8
// Read only (CV_8 - Manufacturer ID)
// Reset all CVs to Default (CV_8; Value = 8)
if (cv_data == 8){
LOG(1, "reset of flash triggered via cv8 => 8\n");
flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE);
flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_DEFAULT, FLASH_PAGE_SIZE * 2);
}
break;
// CV_17 must have a value between 11000000->(192dec) and 11100111->(231dec) inclusive
// CV_17 == 192 && CV_18 == 0 -> Address = 0 is also not valid and therefore shall not be set
case 16: //CV_17
if ( (cv_data < 192 || cv_data > 231) || (CV_ARRAY_FLASH[17] == 0 && cv_data == 192) )
break;
regular_cv_write(cv_index,cv_data);
break;
case 17: //CV_18
if(CV_ARRAY_FLASH[16] == 192 && cv_data == 0)
break;
regular_cv_write(cv_index,cv_data);
break;
// CV_31 & CV_32 Index high byte isn't implemented and shall not be set
case 30: //CV_31
case 31: //CV_32
break;
// Regular CV write is carried out
default:
regular_cv_write(cv_index,cv_data);
}
}
// CV Programming function resets core1 and evaluates the type of programming instruction (e.g. write byte)
void program_mode(const uint8_t number_of_bytes, const uint8_t * const byte_array) {
//First check for valid programming command ("address" 112-127)
if (byte_array[number_of_bytes - 1]<128 && byte_array[number_of_bytes - 1]>111) {
const uint8_t instruction_type_mask = 0b00001100;
const uint8_t instruction_type = instruction_type_mask & byte_array[number_of_bytes - 1];
const uint8_t cv_address_ms_bits_mask = 0b00000011;
const uint16_t cv_address_ms_bits = cv_address_ms_bits_mask & byte_array[number_of_bytes - 1];
const uint16_t cv_address = byte_array[number_of_bytes - 2] + (cv_address_ms_bits << 8);
// Before accessing flash, timers and interrupts need to be disabled and core1 needs to be shut down.
if(pid_control_timer.pool)
alarm_pool_destroy(pid_control_timer.pool);
if(speed_helper_timer.pool)
alarm_pool_destroy(speed_helper_timer.pool);
multicore_reset_core1();
const uint32_t saved_interrupts = save_and_disable_interrupts();
// Verify CV bit instruction
if (instruction_type == 0b000001000) {
const uint8_t bit_pos_mask = 0b00000111;
const uint8_t bit_pos = bit_pos_mask&byte_array[number_of_bytes - 3];
const uint8_t bit_val_mask = 0b00000001;
const uint8_t bit_val_uint = (byte_array[number_of_bytes - 3]>>3) & bit_val_mask;
const bool bit_val = bit_val_uint;
verify_cv_bit(cv_address, bit_val, bit_pos);
}
// Verify CV byte instruction
else if (instruction_type == 0b000000100) {
const uint8_t cv_data = byte_array[number_of_bytes - 3];
verify_cv_byte(cv_address, cv_data);
}
// Write CV byte instruction
else if (instruction_type == 0b000001100) {
const uint8_t cv_data = byte_array[number_of_bytes - 3];
write_cv_handler(cv_address, cv_data);
}
// Restore interrupts
restore_interrupts(saved_interrupts);
busy_wait_ms(5);
}
}
// Set outputs according to configuration (PWM on/off, PWM duty cycle/level, ...)
void set_outputs(const uint32_t functions_to_set_bitmask) {
// Get outputs with pwm enabled and preset outputs_to_set_PWM variable with resulting GPIO Bitmask
const uint32_t PWM_enabled_outputs = get_32bit_CV(111);
uint32_t outputs_to_set_PWM = PWM_enabled_outputs;
// Get enabled output configuration corresponding to set functions and direction
uint32_t outputs_to_set = 0;
uint32_t temp_mask = 1;
for (uint8_t i = 0; i < 32; i++) {
if (temp_mask & functions_to_set_bitmask ){
outputs_to_set |= get_32bit_CV(i * 8 + 260 - 4 * get_direction(0));
}
temp_mask<<=1;
}
outputs_to_set_PWM &= outputs_to_set; // Outputs with PWM to be enabled
outputs_to_set &= ~outputs_to_set_PWM; // Outputs without PWM to be enabled
// Set regular outputs without PWM, preventing illegal GPIO by masking with GPIO_ALLOWED_OUTPUTS
gpio_put_masked(GPIO_ALLOWED_OUTPUTS, outputs_to_set);
// Set PWM enabled outputs to desired level
temp_mask = 1;
for (uint8_t i = 0; i < 32; ++i) {
if(temp_mask & outputs_to_set_PWM){
pwm_set_gpio_level(i, level_table[i]);
pwm_gpio_to_channel(i);
pwm_gpio_to_slice_num(i);
}
else if (temp_mask & PWM_enabled_outputs){
pwm_set_gpio_level(i,0);
}
temp_mask<<=1;
}
}
// Update functions F0 - F31 when function command is received or in case of direction change
void update_active_functions(uint32_t new_function_bitmask, uint8_t clr_bit_ind, bool direction_change) {
static uint32_t active_functions;
// Outputs depend on direction
// In case of a direction change every output needs to be set according to configuration for the other direction
if (direction_change) set_outputs(active_functions);
// In case of a change in active functions only the function group corresponding to the instruction is considered
// Check for changes and set outputs accordingly
else{
new_function_bitmask &= ~(clr_bit_arr[clr_bit_ind]); // Clear every bit except bits corresponding to group of functions
active_functions &= clr_bit_arr[clr_bit_ind]; // Clear bits corresponding to group of functions
active_functions |= new_function_bitmask; // Write bits corresponding to group of functions
static uint32_t prev_active_func = 0;
const uint32_t changes = active_functions ^ prev_active_func; // Checks for changes from previous state
if(changes) set_outputs(active_functions);
prev_active_func = active_functions;
}
}
// Bitwise XOR for all Bytes -> Successful result is: "0000 0000"
bool error_detection(const int8_t number_of_bytes, const uint8_t * const byte_array) {
uint8_t xor_byte = 0;
for (int i = 0; i < number_of_bytes; i++) {
xor_byte = xor_byte ^ byte_array[i];
}
return (0 == xor_byte);
}
// Check for long address. Function returns true for long address.
bool is_long_address(const uint8_t number_of_bytes, const uint8_t * const byte_array) {
if ((byte_array[number_of_bytes - 1]>>6) == 0b00000011) return true;
return false;
}
// First checks for idle package and then evaluates address included in byte_array[]
bool address_evaluation(const uint8_t number_of_bytes,const uint8_t * const byte_array) {
// Check for Idle Package
if (byte_array[number_of_bytes - 1] == 255)
{
return false;
}
// Long/extended address decoder configuration (CV_29 Bit5)
const bool CV_29_bit5 = (CV_ARRAY_FLASH[28]&0b00100000)>>5;
uint16_t read_address;
// Decoder configured to receive long/extended address
if (CV_29_bit5){
// Package received does contain a long address -> Check for accordance
if (is_long_address(number_of_bytes, byte_array))
{
// start of transmission -> address_byte_1 -> address_byte_0 -> ... -> end of transmission
const uint16_t address_byte_1 = (byte_array[number_of_bytes - 1]) - 192; // Remove long address identifier bits
const uint16_t address_byte_0 = (byte_array[number_of_bytes - 2]);
read_address = (address_byte_1 << 8) + address_byte_0;
const uint16_t long_address = get_16bit_CV(16) & 0x3FFF; // &Mask to remove long address identifier bits
return (long_address == read_address);
}
// Package received does not contain a long address
else return false;
}
// Short address decoder configuration (CV_29 Bit5)
else
{
// Short Address Package
// start of transmission -> address_byte_0 -> ... -> end of transmission
read_address = byte_array[number_of_bytes - 1];
return CV_ARRAY_FLASH[0] == read_address;
}
}
// Evaluate the type of instruction
void instruction_evaluation(const uint8_t number_of_bytes,const uint8_t * const byte_array) {
// start of transmission -> ... -> command_byte_n -> ... -> command_byte_0 -> ... -> end of transmission
// The position of command bytes depend on whether the address is long or not
uint8_t command_byte_start_index;
if (is_long_address(number_of_bytes,byte_array)) {
command_byte_start_index = number_of_bytes - 3;
}
else {
command_byte_start_index = number_of_bytes - 2;
}
const uint8_t command_byte_n = byte_array[command_byte_start_index];
//0011-1111 (128 Speed Step Control) - 2 Byte length
if (command_byte_n == 0b00111111){
static bool prev_dir;
const uint32_t speed_step = byte_array[command_byte_start_index - 1];
// LOG(1, "new speed %d", speed_step);
multicore_fifo_push_blocking(speed_step);
// LOG(1, " submitted to list");
// In case of a direction change, functions need to be updated because functions might depend on direction state
if (get_direction(0) != prev_dir) {
update_active_functions(0,0,true);
prev_dir = get_direction(0);
}
}
// 10XX-XXXX (Function Group Instruction)
else if (command_byte_n >> 6 == 0b00000010){
switch (command_byte_n >> 4) {
case 0b00001011: // F5-F8
update_active_functions((command_byte_n << 5),1,false);
break;
case 0b00001010: // F9-F12
update_active_functions((command_byte_n << 9),2,false);
break;
default: // F0-F4
update_active_functions((((command_byte_n & 0b00001111) << 1) + ((command_byte_n & 0b00010000) >> 4)),0,false);
break;
}
}
//Feature Expansion Instruction 110X-XXXX
else if (command_byte_n >> 5 == 0b00000110) {
switch (command_byte_n) {
case 0b11011110: // F13-F20
update_active_functions((byte_array[command_byte_start_index - 1] << 13),3,false);
break;
case 0b11011111: // F21-F28
update_active_functions((byte_array[command_byte_start_index - 1] << 21),4,false);
break;
case 0b11011000: // F29-F31
update_active_functions((byte_array[command_byte_start_index - 1] << 29),5,false);
break;
default:
break;
}
}
}
// Check for reset package - When reset package is found stop the motor and disable all functions
bool reset_package_check(const uint8_t number_of_bytes,const uint8_t * const byte_array){
if (byte_array[number_of_bytes-1] == 0b00000000 && byte_array[number_of_bytes-2] == 0b00000000){
const uint32_t speed_step = 1;
multicore_fifo_push_blocking(speed_step); // Emergency Stop
update_active_functions(0,0,0); // Disables all functions
return true;
}
return false;
}
// Checks for valid package - looking for correct preamble
int8_t check_for_package() { //returns number of bytes if valid bit-pattern is found. Otherwise -1 is returned.
const uint64_t package3Masked = input_bit_buffer & PACKAGE_MASK_3_BYTES;
if (package3Masked == PACKAGE_3_BYTES) return 3;
const uint64_t package4Masked = input_bit_buffer & PACKAGE_MASK_4_BYTES;
if (package4Masked == PACKAGE_4_BYTES) return 4;
const uint64_t package5Masked = input_bit_buffer & PACKAGE_MASK_5_BYTES;
if (package5Masked == PACKAGE_5_BYTES) return 5;
return -1;
}
//start of transmission -> byte_n(address byte) -> ... -> byte_0(error detection byte) -> end of transmission
void bits_to_byte_array(int8_t number_of_bytes,uint8_t byte_array[]) {
for (uint8_t i = 0; i < number_of_bytes; i++) {
byte_array[i] = input_bit_buffer >> (i * 9 + 1);
}
}
// Sequence of bits gets evaluated
void evaluation(){
static bool core1_launched = false;
static bool reset_package_flag;
const int8_t number_of_bytes = check_for_package();
// number_of_bytes contains the amount of bytes when the package is valid, otherwise -1
if (number_of_bytes != -1) {
// Split data into 8Bit array
uint8_t byte_array[SIZE_BYTE_ARRAY] = {0};
bits_to_byte_array(number_of_bytes,byte_array);
// Check for errors
if (error_detection(number_of_bytes,byte_array)) {
// Check for matching address
if (address_evaluation(number_of_bytes,byte_array)) {
reset_package_flag = false;
if (!core1_launched){
multicore_launch_core1(core1_entry);
// Wait for pid.direction pointer via multicore fifo also signalizing that core1 initialization is finished.
get_direction((bool *) multicore_fifo_pop_blocking());
core1_launched = true;
}
instruction_evaluation(number_of_bytes,byte_array);
}
// When previous packet was a reset package -> enter program mode
else if (reset_package_flag) {
program_mode(number_of_bytes,byte_array);
}
// Check for reset package and set flag when reset package is received
else {
reset_package_flag = reset_package_check(number_of_bytes,byte_array);
}
}
}
}
// DCC-Signal (GPIO 21) rising edge interrupt
void track_signal_rise(const unsigned int gpio, const long unsigned int events) {
// Save current timer value
rising_edge_time = get_absolute_time();
// Disable rising edge interrupt and enable falling edge interrupt
gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE, false, &track_signal_rise);
gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_FALL, true, &track_signal_fall);
}
// DCC-Signal (GPIO 21) falling edge interrupt
void track_signal_fall( const unsigned int gpio, const long unsigned int events) {
// Save current timer value
falling_edge_time = get_absolute_time();
// Time difference is equal to the time the signal was in a logical high state
const int64_t time_logical_high = absolute_time_diff_us(rising_edge_time,falling_edge_time);
// When logical high was longer than 87us write 0 bit into buffer otherwise 1
bool bit;
if(time_logical_high > 87) bit = 0;
else bit = 1;
input_bit_buffer <<= 1;
input_bit_buffer |= bit;
// evaluate sequence of bits saved in buffer
evaluation();
// Disable falling edge interrupt and enable rising edge interrupt
gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_FALL, false, &track_signal_fall);
gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE, true, &track_signal_rise);
}
// Output initialization function - Configures pwm frequency and clock divider according to CV_111 - CV_171
void init_outputs(){
gpio_init_mask(GPIO_ALLOWED_OUTPUTS);
gpio_set_dir_out_masked(GPIO_ALLOWED_OUTPUTS); // Note: This might also disable UART on GPIO0 & GPIO1
const uint32_t PWM_enabled_outputs = get_32bit_CV(111) & GPIO_ALLOWED_OUTPUTS;
uint32_t mask = 1;
for (uint8_t i = 0; i < 32; ++i) {
if (PWM_enabled_outputs & mask){
const uint32_t slice = pwm_gpio_to_slice_num(i);
const uint32_t channel = pwm_gpio_to_channel(i); // Channel A = "0"; Channel B = "1"
const uint16_t wrap = get_16bit_CV(115 + 7*slice);
const uint16_t level = get_16bit_CV(118 + 7*slice + 2*channel);
const uint8_t clock_divider = CV_ARRAY_FLASH[117+7*slice] + 1;
gpio_set_function(i,GPIO_FUNC_PWM);
pwm_set_wrap(slice,wrap);
pwm_set_gpio_level(i,0);
level_table[i] = level;
pwm_set_clkdiv_int_frac(slice,clock_divider,0);
pwm_set_enabled(slice,true);
}
mask<<=1;
}
}
// Measures "base" pwm duty cycle needed to overcome friction
uint16_t measure_base_pwm(const bool direction, const uint8_t iterations){
uint gpio;
if (direction) gpio = MOTOR_FWD_PIN;
else gpio = MOTOR_REV_PIN;
float level_arr[iterations];
for (int i = 0; i < iterations; ++i) {
const uint16_t max_level = _125M/(CV_ARRAY_FLASH[8]*100+10000);
uint16_t level = max_level/20;
LOG(3, "iteration %d: maxlevel %d level %d\n", i, max_level, level);
float measurement;
do {
pwm_set_gpio_level(gpio, level);
busy_wait_ms(30);
level += max_level/500;
measurement = measure(CV_ARRAY_FLASH[60],
CV_ARRAY_FLASH[61],
CV_ARRAY_FLASH[62],
CV_ARRAY_FLASH[63],
direction);
LOG(3, "level %d measurement %f loop-cond: %f\n", level, measurement, measurement-(float)CV_ARRAY_FLASH[171]);
if (level > max_level) {
// Abort measurement and write default value of 0 to flash
LOG(1, "measure_base_pwm: abort measurement and return 0\n");
return 0;
}
} while((measurement - (float)CV_ARRAY_FLASH[171]) < 5.0f);
LOG(3, "level_arr[%d] = %f\n", i, level);
level_arr[i] = (float)level;
busy_wait_ms(100);
}
// Find and return overall average discarding outliers in measurement - multiply with 0.9
const float retVal = 0.9f*two_std_dev(level_arr,5);
LOG(1, "measure_base_pwm: %d(%f)\n", (uint16_t)retVal, retVal);
return (uint16_t)(retVal);
}
// Check for flash memory factory condition and adc offset setup
// When factory condition is found the CV_ARRAY_DEFAULT will be written into flash
// When ADC Setup is not configured run adc offset adjustment function and write adc offset into flash
void cv_setup_check(){
// Check for flash factory setting and set CV_FLASH_ARRAY to default values when factory condition ("0xFF") is found.
if ( CV_ARRAY_FLASH[64] == 0xFF ){
LOG(1, "found cv[64] equals to 0xff, reseting CVs (and CV[8] = 8)\n");
const uint8_t arr[4] = {125,8,7,124};
program_mode(4,arr); //reset to CV_ARRAY_DEFAULT (write CV_8 = 8)
}
// Check for adc offset setup
if ( CV_ARRAY_FLASH[171] == 0xFF ){
LOG(1, "found cv[171] equals to 0xff, adc offset adjstments (and cr[7] = 7)\n");
const uint8_t arr[4] = {125,7,6,124};
program_mode(4,arr); //ADC offset adjustment (write CV_7 = 7)
}
// Check for base PWM configuration - used for feed-forward
// Forward Direction
if (get_16bit_CV(175) == 0){
LOG(1, "found cv[175] equals to 0, forward direction\n");
const uint16_t base_pwm_fwd = measure_base_pwm(true,10);
const uint8_t base_pwm_fwd_high_byte = base_pwm_fwd>>8;
const uint8_t base_pwm_fwd_low_byte = base_pwm_fwd&0x00FF;
const uint8_t arr0[4] = {125,base_pwm_fwd_high_byte,175,124};
program_mode(4,arr0);
const uint8_t arr1[4] = {125,base_pwm_fwd_low_byte,176,124};
program_mode(4,arr1);
}
// Reverse Direction
if (get_16bit_CV(177) == 0){
LOG(1, "found cv[177] equals to 0, reverse direction\n");
const uint16_t base_pwm_rev = measure_base_pwm(false,10);
const uint8_t base_pwm_rev_high_byte = base_pwm_rev>>8;
const uint8_t base_pwm_rev_low_byte = base_pwm_rev&0x00FF;
const uint8_t arr0[4] = {125,base_pwm_rev_high_byte,177,124};
program_mode(4,arr0);
const uint8_t arr1[4] = {125,base_pwm_rev_low_byte,178,124};
program_mode(4,arr1);
}
LOG(1, "int_lim_max %d\n", CV_ARRAY_FLASH[51]);
LOG(1, "int_lim_min %d\n", CV_ARRAY_FLASH[52]);
}
// This function ensures that the direction pointer can only be written once.
// After first initialization this function can be called with arbitrary input to get the current direction
bool get_direction(bool *direction_ptr){
static bool set_flag;
static bool *dir_ptr;
if(!set_flag) {
if (direction_ptr == NULL){
LOG(0, "Error! Direction pointer argument is NULL-pointer!\n")
}
else {
set_flag = true;
dir_ptr = direction_ptr;
}
}
return *dir_ptr;
}
// Motor PWM initialization
void init_motor_pwm(const uint8_t gpio) {
const uint16_t wrap_counter = (_125M/(CV_ARRAY_FLASH[8]*100+10000)) - 1;
const uint32_t slice_num = pwm_gpio_to_slice_num(gpio);
pwm_set_clkdiv_int_frac(slice_num,CV_ARRAY_FLASH[173],0);
pwm_set_wrap(slice_num, wrap_counter);
pwm_set_gpio_level(gpio,0);
pwm_set_enabled(slice_num, true);
LOG(2, "init motor(%d): wrapCounter %d clkdiv %d\n", gpio, wrap_counter, CV_ARRAY_FLASH[173]);
}
// Main initialization - GPIO Config / ADC Config
void init_gpio_adc(){
if(gpio_get_function(MOTOR_FWD_PIN) != 4){
gpio_set_function(MOTOR_FWD_PIN, GPIO_FUNC_PWM);
gpio_set_function(MOTOR_REV_PIN, GPIO_FUNC_PWM);
adc_init();
adc_gpio_init(FWD_V_EMF_ADC_PIN);
adc_gpio_init(REV_V_EMF_ADC_PIN);
adc_fifo_setup(true,false,0,false,false);
}
}
int main() {
stdio_init_all();
LOG(1, "\n\n======\ncore0 init\n");
init_gpio_adc();
LOG(1, "init motor pwms\n");
init_motor_pwm(MOTOR_FWD_PIN);
init_motor_pwm(MOTOR_REV_PIN);
LOG(1, "check cvs\n");
cv_setup_check();
LOG(1, "init outputs\n");
init_outputs();
LOG(1, "init gpios\n");
gpio_init(DCC_INPUT_PIN);
gpio_set_dir(DCC_INPUT_PIN, GPIO_IN);
gpio_pull_up(DCC_INPUT_PIN);
gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE, true, &track_signal_rise);
LOG(1, "core0 done\n");
while (1);
}