Hardware Description

Overview

Block Diagram

The above block diagram gives a general overview regarding the operation of components. For better illustration it has been divided into four functional blocks. Furthermore, these functional blocks can be subdivided and will be explained below.

  • Input Stage - DCC Signal Level Shift - Bridge Rectifier & Voltage Regulator

  • Motor Driver - Motor Driver - Back EMF measurement (ADC)

  • General Purpose - GPIO - Auxiliary output

  • Microcontroller - Flash memory - Crystal oscillator

Characteristics

Characteristics table

Parameter

Symbol

Minimum

Maximum

Unit

Absolute max. DCC Input Voltage

VDCC

-25

+25

V

Absolute max. GPIO Voltage(0)

VPIN

-0.5

3.3+0.5

V

Input Voltage High(0)

VIH

2.145

3.6

V

Input Voltage Low(0)

VIL

0

1.155

V

Total GPIO Current(0)

IIOVDD

50

mA

Absolute max. motor output current(1)

IMOTOR

2.8

A

Absolute max. auxiliary output current (2)

IAUX

400

mA

(0): According to: RP2040 Datasheet (assuming VDD= 3.3V)

(1): According to: BDR6133 Datasheet

(2): According to: T2N7002BK Datasheet

Input Stage

Input Stage

D1 Rectifies the DCC square-wave into +V, the amplitude is not critical as long as it’s within the 25V limit. The rectified voltage +V is then provided to the 3.3V voltage regulator (U1) and to the motor driver (U2).

The MOSFET on the right effectively translates the rather high DCC voltage to a suitable level for the microcontroller to process. When Q1 is turned off GPIO21 is pulled high by the RP2040 internal pull-up resistor, as soon as Q1 gets turned on (V<sub>GS</sub> > V<sub>GS,th</sub>), GPIO21 gets pulled to GND potential. R1 and R2 ensure that V<sub>GS</sub> doesn’t exceed ±20V.

Motor Driver

Motor Driver

The Motor Driver is a complete H-Bridge IC specifically made for DC-Motors.

In order to control the motor, it is necessary to measure the back-EMF. This is done by the ADC, which measures at Points ADC_EMF_A and ADC_EMF_B respectively. The two resistors are used as a voltage divider.

Auxiliary Output

Auxiliary Output

Switching of loads up to a maximum of about ~400mA can be done using four N-Channel MOSFETs. They are switching on the low-side, which means the load effectively gets connected to GND potential as the transistor starts to conduct. GPIO24 - GPIO27 are used.

GPIO

To switch lighter loads, six soldering pads on the back side of the PCB are connected to GPIO0 - GPIO5 pins. Although not implemented yet, they could theoretically be used as inputs as well (e.g., Reed switch).

Microcontroller

Microcontroller

The Microcontroller needs a crystal oscillator to function properly. External flash memory is also needed as it holds the configuration variables and the program itself. R3 & C14 are used to filter ADC_AVDD (ADC Reference Voltage).

Complete Schematic

Complete Schematic

BOM & Alternative Parts

BOM

Ref

Quantity

Value Component Type

Component Name

Footprint

C1, C2, C5, C6, C14

5

10u

Ceramic Capacitor

/

0603_1608Metric

C3, C4, C7, C8, C9, C10, C11, C12, C13, C15

10

100n

Ceramic Capacitor

/

0603_1608Metric

C16, C17

2

33p

Ceramic Capacitor

/

0603_1608Metric

D1

1

VRMS=40V, IF=2A

Bridge Rectifier

KMB24F

MBS (TO-269AA)

Q1, Q2, Q3, Q4, Q5

5

VDS=60V, ID=0.4A

N-Channel MOSFET

T2N7002BK

SOT-23

R1, R2, R5, R6

4

6k8

Resistor

/

0603_1608Metric

R3

1

200

Resistor

/

0603_1608Metric

R7, R8, R9

3

1k

Resistor

/

0603_1608Metric

U1

1

VOUT=3.3V

Low Dropout Voltage Regulator

HT7533S

SOT-23

U2

1

I=2.8A

H-Bridge Driver

BDR6133

SOIC-8

U3

1

64Mb

Flash Memory

W25Q64JVSSIQ

SOIC-8

U4

1

/

Microcontroller

RP2040

QFN-56-1EP_7x7mm_P0.4mm

Y1

1

f=12MHz

Crystal Oscillator

X322512MSB4SI

Crystal_SMD_3225-4Pin_3.2x2.5mm

NOTE: Keep capacitor Vmax in mind!

Alternatives for BDR6133:

Alternative for HT7533S: