some refactoring
This commit is contained in:
1 parent
a57295817e
commit
a0408c28ed
3 files changed
+47
-14
No files matched your search
@@ -45,6 +45,8 @@ float two_std_dev(const float arr[], uint32_t length){
|
||||
|
||||
// Measures constant adc offset and programs the offset into flash
|
||||
void adc_offset_adjustment(uint32_t n){
|
||||
LOG(1, "adc_offset_adjustment\n");
|
||||
|
||||
float offsets_fwd[n];
|
||||
float offsets_rev[n];
|
||||
// Set PWM level to 0 just to be sure
|
||||
@@ -131,18 +133,24 @@ void write_cv_handler(uint16_t cv_index, uint8_t cv_data){
|
||||
switch (cv_index) {
|
||||
case 0: //CV_1
|
||||
// CV_1 => Value = 0 is not allowed
|
||||
if (cv_data == 0 || cv_data > 127) break;
|
||||
else regular_cv_write(cv_index,cv_data);
|
||||
if (cv_data == 0 || cv_data > 127)
|
||||
break;
|
||||
else
|
||||
regular_cv_write(cv_index,cv_data);
|
||||
break;
|
||||
case 6: //CV_7
|
||||
// Read only (CV_7 - Version no.)
|
||||
// ADC offset Adjustment (CV_7; Value = 7);
|
||||
if (cv_data == 7) adc_offset_adjustment(8192);
|
||||
if (cv_data == 7) {
|
||||
LOG(1, "trigger adc offset adjustment via cv7 => 7\n");
|
||||
adc_offset_adjustment(8192);
|
||||
}
|
||||
break;
|
||||
case 7: //CV_8
|
||||
// Read only (CV_8 - Manufacturer ID)
|
||||
// Reset all CVs to Default (CV_8; Value = 8)
|
||||
if (cv_data == 8){
|
||||
LOG(1, "reset of flash triggered via cv8 => 8\n");
|
||||
flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE);
|
||||
flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_DEFAULT, FLASH_PAGE_SIZE * 2);
|
||||
}
|
||||
@@ -150,12 +158,16 @@ void write_cv_handler(uint16_t cv_index, uint8_t cv_data){
|
||||
// CV_17 must have a value between 11000000->(192dec) and 11100111->(231dec) inclusive
|
||||
// CV_17 == 192 && CV_18 == 0 -> Address = 0 is also not valid and therefore shall not be set
|
||||
case 16: //CV_17
|
||||
if ( (cv_data < 192 || cv_data > 231) || (CV_ARRAY_FLASH[17] == 0 && cv_data == 192) ) break;
|
||||
else regular_cv_write(cv_index,cv_data);
|
||||
if ( (cv_data < 192 || cv_data > 231) || (CV_ARRAY_FLASH[17] == 0 && cv_data == 192) )
|
||||
break;
|
||||
else
|
||||
regular_cv_write(cv_index,cv_data);
|
||||
break;
|
||||
case 17: //CV_18
|
||||
if(CV_ARRAY_FLASH[16] == 192 && cv_data == 0) break;
|
||||
else regular_cv_write(cv_index,cv_data);
|
||||
if(CV_ARRAY_FLASH[16] == 192 && cv_data == 0)
|
||||
break;
|
||||
else
|
||||
regular_cv_write(cv_index,cv_data);
|
||||
break;
|
||||
// CV_31 & CV_32 Index high byte isn't implemented and shall not be set
|
||||
case 30: //CV_31
|
||||
@@ -169,9 +181,9 @@ void write_cv_handler(uint16_t cv_index, uint8_t cv_data){
|
||||
|
||||
|
||||
// CV Programming function resets core1 and evaluates the type of programming instruction (e.g. write byte)
|
||||
void program_mode(uint8_t number_of_bytes, const uint8_t * const byte_array){
|
||||
void program_mode(uint8_t number_of_bytes, const uint8_t * const byte_array) {
|
||||
//First check for valid programming command ("address" 112-127)
|
||||
if (byte_array[number_of_bytes - 1]<128 && byte_array[number_of_bytes - 1]>111){
|
||||
if (byte_array[number_of_bytes - 1]<128 && byte_array[number_of_bytes - 1]>111) {
|
||||
uint8_t instruction_type_mask = 0b00001100;
|
||||
uint8_t instruction_type = instruction_type_mask & byte_array[number_of_bytes - 1];
|
||||
uint8_t cv_address_ms_bits_mask = 0b00000011;
|
||||
@@ -179,9 +191,13 @@ void program_mode(uint8_t number_of_bytes, const uint8_t * const byte_array){
|
||||
uint16_t cv_address = byte_array[number_of_bytes - 2] + (cv_address_ms_bits << 8);
|
||||
|
||||
// Before accessing flash, timers and interrupts need to be disabled and core1 needs to be shut down.
|
||||
if(pid_control_timer.pool)alarm_pool_destroy(pid_control_timer.pool);
|
||||
if(speed_helper_timer.pool)alarm_pool_destroy(speed_helper_timer.pool);
|
||||
if(pid_control_timer.pool)
|
||||
alarm_pool_destroy(pid_control_timer.pool);
|
||||
if(speed_helper_timer.pool)
|
||||
alarm_pool_destroy(speed_helper_timer.pool);
|
||||
|
||||
multicore_reset_core1();
|
||||
|
||||
uint32_t saved_interrupts = save_and_disable_interrupts();
|
||||
|
||||
// Verify CV bit instruction
|
||||
@@ -549,15 +565,16 @@ uint16_t measure_base_pwm(bool direction, uint8_t iterations){
|
||||
// When factory condition is found the CV_ARRAY_DEFAULT will be written into flash
|
||||
// When ADC Setup is not configured run adc offset adjustment function and write adc offset into flash
|
||||
void cv_setup_check(){
|
||||
|
||||
// Check for flash factory setting and set CV_FLASH_ARRAY to default values when factory condition ("0xFF") is found.
|
||||
if ( CV_ARRAY_FLASH[64] == 0xFF ){
|
||||
LOG(1, "found cv[64] equals to 0xff, reseting CVs (and CV[8] = 8)\n");
|
||||
uint8_t arr[4] = {125,8,7,124};
|
||||
program_mode(4,arr); //reset to CV_ARRAY_DEFAULT (write CV_8 = 8)
|
||||
}
|
||||
|
||||
// Check for adc offset setup
|
||||
if ( CV_ARRAY_FLASH[171] == 0xFF ){
|
||||
LOG(1, "found cv[171] equals to 0xff, adc offset adjustments (and cr[8] = 8)\n");
|
||||
uint8_t arr[4] = {125,7,6,124};
|
||||
program_mode(4,arr); //ADC offset adjustment (write CV_7 = 7)
|
||||
}
|
||||
@@ -565,6 +582,7 @@ void cv_setup_check(){
|
||||
// Check for base PWM configuration - used for feed-forward
|
||||
// Forward Direction
|
||||
if (get_16bit_CV(175) == 0){
|
||||
LOG(1, "found cv[175] equals to 0, forward direction\n");
|
||||
uint16_t base_pwm_fwd = measure_base_pwm(true,10);
|
||||
uint8_t base_pwm_fwd_high_byte = base_pwm_fwd>>8;
|
||||
uint8_t base_pwm_fwd_low_byte = base_pwm_fwd&0x00FF;
|
||||
@@ -575,6 +593,7 @@ void cv_setup_check(){
|
||||
}
|
||||
// Reverse Direction
|
||||
if (get_16bit_CV(177) == 0){
|
||||
LOG(1, "found cv[177] equals to 0, reverse direction\n");
|
||||
uint16_t base_pwm_rev = measure_base_pwm(false,10);
|
||||
uint8_t base_pwm_rev_high_byte = base_pwm_rev>>8;
|
||||
uint8_t base_pwm_rev_low_byte = base_pwm_rev&0x00FF;
|
||||
@@ -625,16 +644,20 @@ void init_main(){
|
||||
|
||||
int main() {
|
||||
stdio_init_all();
|
||||
printf("core0 init...\n");
|
||||
LOG(0, "core0 init\n");
|
||||
init_main();
|
||||
LOG(1, "init motor pwms\n");
|
||||
init_motor_pwm(MOTOR_FWD_PIN);
|
||||
init_motor_pwm(MOTOR_REV_PIN);
|
||||
LOG(1, "check cvs\n");
|
||||
cv_setup_check();
|
||||
LOG(1, "init outputs\n");
|
||||
init_outputs();
|
||||
LOG(1, "init gpios\n");
|
||||
gpio_init(DCC_INPUT_PIN);
|
||||
gpio_set_dir(DCC_INPUT_PIN, GPIO_IN);
|
||||
gpio_pull_up(DCC_INPUT_PIN);
|
||||
gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE, true, &track_signal_rise);
|
||||
printf("core0 done\n");
|
||||
LOG(0, "core0 done\n");
|
||||
while (1);
|
||||
}
|
||||
@@ -30,6 +30,13 @@ void verify_cv_bit(uint16_t cv_address,bool bit_val, uint8_t bit_pos);
|
||||
void verify_cv_byte(uint16_t cv_address, uint8_t cv_data);
|
||||
void regular_cv_write(uint16_t cv_index, uint8_t cv_data);
|
||||
void write_cv_handler(uint16_t cv_index, uint8_t cv_data);
|
||||
|
||||
|
||||
#define ProgramInstrVerifyBit 0b10
|
||||
#define ProgramInstrVerifyByte 0b01
|
||||
#define ProgramInstrWriteByte 0b11
|
||||
#define ProgramCmd(instr, adrmsbits) ((instr<<2) | (adrmsbits))
|
||||
|
||||
void program_mode(uint8_t number_of_bytes, const uint8_t byte_array[]);
|
||||
void set_outputs(uint32_t functions_to_set_bitmask);
|
||||
void update_active_functions(uint32_t byte, uint8_t clr_bit_ind,bool direction_change);
|
||||
|
||||
Reference in new issue
Block a user