- Minor changes to variable names, comments & formatting
- Removed obsolete parameter previously used in program_mode - Added correction constant regarding base pwm measurement - Revised GPIO definitions (shared.h)
This commit is contained in:
1 parent
bae6fff659
commit
0219963dd7
5 files changed
+106
-98
No files matched your search
@@ -5,6 +5,7 @@
|
||||
//////////////////////////
|
||||
|
||||
#include "core0.h"
|
||||
// XIP_BASE + FLASH_TARGET_OFFSET = "0x101FF000"
|
||||
const uint8_t *CV_ARRAY_FLASH = (const uint8_t *) (XIP_BASE + FLASH_TARGET_OFFSET);
|
||||
uint64_t input_bit_buffer = 0;
|
||||
uint16_t level_table[32] = {0};
|
||||
@@ -98,7 +99,7 @@ void acknowledge() {
|
||||
}
|
||||
|
||||
|
||||
// When Bit matches sent byte -> acknowledge()
|
||||
// When bit matches sent byte -> acknowledge()
|
||||
void verify_cv_bit(uint16_t cv_address,bool bit_val, uint8_t bit_pos) {
|
||||
uint8_t mask = 0b00000001;
|
||||
bool res = ( (CV_ARRAY_FLASH[cv_address] >> bit_pos) &mask ) == bit_val;
|
||||
@@ -108,11 +109,13 @@ void verify_cv_bit(uint16_t cv_address,bool bit_val, uint8_t bit_pos) {
|
||||
}
|
||||
|
||||
|
||||
// When Byte matches sent byte -> acknowledge()
|
||||
// When byte matches sent byte -> acknowledge()
|
||||
void verify_cv_byte(uint16_t cv_address, uint8_t cv_data){
|
||||
if (CV_ARRAY_FLASH[cv_address] == cv_data) acknowledge();
|
||||
}
|
||||
|
||||
|
||||
// CV writing function first erases necessary amount of blocks in flash and then rewrites to flash
|
||||
void regular_cv_write(uint16_t cv_index, uint8_t cv_data){
|
||||
uint8_t CV_ARRAY_TEMP[CV_ARRAY_SIZE];
|
||||
memcpy(CV_ARRAY_TEMP, CV_ARRAY_FLASH, sizeof(CV_ARRAY_TEMP));
|
||||
@@ -123,41 +126,39 @@ void regular_cv_write(uint16_t cv_index, uint8_t cv_data){
|
||||
}
|
||||
|
||||
|
||||
// CV writing function first erases block in flashes and then rewrites to flash
|
||||
// Writing to read-only functions also gets handled here (e.g. complete reset to default)
|
||||
// There are some exceptions to writing CVs - e.g. writing to a read only CV is not valid - this gets handled here
|
||||
void write_cv_handler(uint16_t cv_index, uint8_t cv_data){
|
||||
switch (cv_index) {
|
||||
// CV_1 => Value = 0 is not allowed
|
||||
case 0:
|
||||
case 0: //CV_1
|
||||
// CV_1 => Value = 0 is not allowed
|
||||
if (cv_data == 0 || cv_data > 127) break;
|
||||
// CV_7 & CV_8 are read-only
|
||||
// ADC offset Adjustment (CV_7; Value = 7);
|
||||
case 6:
|
||||
case 6: //CV_7
|
||||
// Read only (CV_7 - Version no.)
|
||||
// ADC offset Adjustment (CV_7; Value = 7);
|
||||
if (cv_data == 7) adc_offset_adjustment(8192);
|
||||
break;
|
||||
// Reset all CVs to Default (CV_8; Value = 8)
|
||||
case 7:
|
||||
case 7: //CV_8
|
||||
// Read only (CV_8 - Manufacturer ID)
|
||||
// Reset all CVs to Default (CV_8; Value = 8)
|
||||
if (cv_data == 8){
|
||||
flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE);
|
||||
flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_DEFAULT, FLASH_PAGE_SIZE * 2);
|
||||
}
|
||||
break;
|
||||
|
||||
// CV_17 must have a value between 11000000->(192dec) and 11100111->(231dec) inclusive
|
||||
// CV_17 == 192 && CV_18 == 0 -> Address = 0 is also not valid and therefore shall not be set
|
||||
case 16:
|
||||
case 16: //CV_17
|
||||
if ( (cv_data < 192 || cv_data > 231) || (CV_ARRAY_FLASH[17] == 0 && cv_data == 192) ) break;
|
||||
else regular_cv_write(cv_index,cv_data);
|
||||
break;
|
||||
case 17:
|
||||
case 17: //CV_18
|
||||
if(CV_ARRAY_FLASH[16] == 192 && cv_data == 0) break;
|
||||
else regular_cv_write(cv_index,cv_data);
|
||||
break;
|
||||
// CV_31 & CV_32 Index high byte isn't implemented and shall not be set
|
||||
case 30:
|
||||
case 31:
|
||||
case 30: //CV_31
|
||||
case 31: //CV_32
|
||||
break;
|
||||
|
||||
// Regular CV write is carried out
|
||||
default:
|
||||
regular_cv_write(cv_index,cv_data);
|
||||
@@ -166,7 +167,7 @@ void write_cv_handler(uint16_t cv_index, uint8_t cv_data){
|
||||
|
||||
|
||||
// CV Programming function resets core1 and evaluates the type of programming instruction (e.g. write byte)
|
||||
void program_mode(uint8_t number_of_bytes, const uint8_t * const byte_array, bool restart_core1){
|
||||
void program_mode(uint8_t number_of_bytes, const uint8_t * const byte_array){
|
||||
//First check for valid programming command ("address" 112-127)
|
||||
if (byte_array[number_of_bytes - 1]<128 && byte_array[number_of_bytes - 1]>111){
|
||||
uint8_t instruction_type_mask = 0b00001100;
|
||||
@@ -210,25 +211,28 @@ void program_mode(uint8_t number_of_bytes, const uint8_t * const byte_array, boo
|
||||
}
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
// Set outputs according to configuration (PWM on/off, PWM duty cycle/level, ...)
|
||||
void set_outputs(uint32_t functions_to_set_bitmask) {
|
||||
// Get outputs with pwm enabled and preset outputs_to_set_PWM variable with resulting GPIO Bitmask
|
||||
uint32_t PWM_enabled_outputs = get_32bit_CV(111);
|
||||
uint32_t outputs_to_set_PWM = PWM_enabled_outputs;
|
||||
|
||||
// Get enabled output configuration corresponding to set functions and direction
|
||||
uint32_t outputs_to_set = 0;
|
||||
uint32_t outputs_with_PWM_enabled = get_32bit_CV(111); //get outputs with pwm enabled (bitmask) // TODO: Verify - should be fine...
|
||||
uint32_t outputs_to_set_PWM = outputs_with_PWM_enabled;
|
||||
uint32_t temp_mask = 1;
|
||||
for (uint8_t i = 0; i < 32; i++) {
|
||||
if (temp_mask & functions_to_set_bitmask ){
|
||||
//outputs_to_set |= get_32bit_CV(i * 8 + 260 - 4 * get_direction(0)); //TODO: verify
|
||||
outputs_to_set |= get_32bit_CV(i * 8 + 260 - 4 * get_direction(0));
|
||||
}
|
||||
temp_mask<<=1;
|
||||
}
|
||||
outputs_to_set &= GPIO_ALLOWED_OUTPUTS; // Prevent illegal GPIO
|
||||
outputs_to_set_PWM &= outputs_to_set; // Outputs with PWM to be enabled
|
||||
outputs_to_set &= ~outputs_to_set_PWM; // Outputs without PWM to be enabled
|
||||
|
||||
// Set regular outputs without PWM, preventing illegal GPIO by masking with GPIO_ALLOWED_OUTPUTS
|
||||
gpio_put_masked(GPIO_ALLOWED_OUTPUTS, outputs_to_set);
|
||||
|
||||
// Set PWM enabled outputs to desired level
|
||||
temp_mask = 1;
|
||||
for (uint8_t i = 0; i < 32; ++i) {
|
||||
if(temp_mask & outputs_to_set_PWM){
|
||||
@@ -236,7 +240,7 @@ void set_outputs(uint32_t functions_to_set_bitmask) {
|
||||
pwm_gpio_to_channel(i);
|
||||
pwm_gpio_to_slice_num(i);
|
||||
}
|
||||
else if (temp_mask & outputs_with_PWM_enabled){
|
||||
else if (temp_mask & PWM_enabled_outputs){
|
||||
pwm_set_gpio_level(i,0);
|
||||
}
|
||||
temp_mask<<=1;
|
||||
@@ -248,15 +252,19 @@ void set_outputs(uint32_t functions_to_set_bitmask) {
|
||||
void update_active_functions(uint32_t new_function_bitmask, uint8_t clr_bit_ind, bool direction_change) {
|
||||
static uint32_t active_functions;
|
||||
static uint32_t prev_active_func;
|
||||
if (direction_change){
|
||||
set_outputs(prev_active_func);
|
||||
}
|
||||
|
||||
// Outputs depend on direction
|
||||
// In case of a direction change every output needs to be set according to configuration for the other direction
|
||||
if (direction_change) set_outputs(active_functions);
|
||||
|
||||
// In case of a change in active functions only the function group corresponding to the instruction is considered
|
||||
// Check for changes and set outputs accordingly
|
||||
else{
|
||||
new_function_bitmask &= ~(clr_bit_arr[clr_bit_ind]); //clear every bit except bits corresponding to group of functions
|
||||
active_functions &= clr_bit_arr[clr_bit_ind]; //clear bits corresponding to group of functions
|
||||
active_functions |= new_function_bitmask; //write bits corresponding to group of functions
|
||||
uint32_t changes = active_functions ^ prev_active_func; //xor effectively checks for changes from previous state
|
||||
if(changes)set_outputs(active_functions);
|
||||
new_function_bitmask &= ~(clr_bit_arr[clr_bit_ind]); // Clear every bit except bits corresponding to group of functions
|
||||
active_functions &= clr_bit_arr[clr_bit_ind]; // Clear bits corresponding to group of functions
|
||||
active_functions |= new_function_bitmask; // Write bits corresponding to group of functions
|
||||
uint32_t changes = active_functions ^ prev_active_func; // Checks for changes from previous state
|
||||
if(changes) set_outputs(active_functions);
|
||||
prev_active_func = active_functions;
|
||||
}
|
||||
}
|
||||
@@ -334,11 +342,14 @@ void instruction_evaluation(uint8_t number_of_bytes,const uint8_t * const byte_a
|
||||
|
||||
//0011-1111 (128 Speed Step Control) - 2 Byte length
|
||||
if (command_byte_n == 0b00111111){
|
||||
bool prev_dir = get_direction(0);
|
||||
static bool prev_dir;
|
||||
uint32_t speed_step = byte_array[command_byte_start_index - 1];
|
||||
multicore_fifo_push_blocking(speed_step);
|
||||
// In case of a direction change, functions need to be updated because functions might depend on direction state
|
||||
if (get_direction(0) != prev_dir) update_active_functions(0,0,true);
|
||||
if (get_direction(0) != prev_dir) {
|
||||
update_active_functions(0,0,true);
|
||||
prev_dir = get_direction(0);
|
||||
}
|
||||
}
|
||||
|
||||
// 10XX-XXXX (Function Group Instruction)
|
||||
@@ -379,30 +390,22 @@ void instruction_evaluation(uint8_t number_of_bytes,const uint8_t * const byte_a
|
||||
bool reset_package_check(uint8_t number_of_bytes,const uint8_t * const byte_array){
|
||||
if (byte_array[number_of_bytes-1] == 0b00000000 && byte_array[number_of_bytes-2] == 0b00000000){
|
||||
uint32_t speed_step = 1;
|
||||
multicore_fifo_push_blocking(speed_step);
|
||||
update_active_functions(0,0,0); //TODO: is this correct?
|
||||
multicore_fifo_push_blocking(speed_step); // Emergency Stop
|
||||
update_active_functions(0,0,0); // Disables all functions
|
||||
return true;
|
||||
}
|
||||
else {
|
||||
return false;
|
||||
}
|
||||
else return false;
|
||||
}
|
||||
|
||||
|
||||
// Checks for valid package - looking for correct preamble
|
||||
int8_t check_for_package() { //returns number of bytes if valid bit-pattern is found. Otherwise -1 is returned.
|
||||
uint64_t package3Masked = input_bit_buffer & PACKAGE_MASK_3_BYTES;
|
||||
if (package3Masked == PACKAGE_3_BYTES) {
|
||||
return 3;
|
||||
}
|
||||
if (package3Masked == PACKAGE_3_BYTES) return 3;
|
||||
uint64_t package4Masked = input_bit_buffer & PACKAGE_MASK_4_BYTES;
|
||||
if (package4Masked == PACKAGE_4_BYTES) {
|
||||
return 4;
|
||||
}
|
||||
if (package4Masked == PACKAGE_4_BYTES) return 4;
|
||||
uint64_t package5Masked = input_bit_buffer & PACKAGE_MASK_5_BYTES;
|
||||
if (package5Masked == PACKAGE_5_BYTES) {
|
||||
return 5;
|
||||
}
|
||||
if (package5Masked == PACKAGE_5_BYTES) return 5;
|
||||
return -1;
|
||||
}
|
||||
|
||||
@@ -420,7 +423,7 @@ void evaluation(){
|
||||
static bool core1_launched = false;
|
||||
static bool reset_package_flag;
|
||||
int8_t number_of_bytes = check_for_package();
|
||||
// number of bytes is != -1 when the package is valid
|
||||
// number_of_bytes contains the amount of bytes when the package is valid, otherwise -1
|
||||
if (number_of_bytes != -1) {
|
||||
// Split data into 8Bit array
|
||||
uint8_t byte_array[SIZE_BYTE_ARRAY] = {0};
|
||||
@@ -440,7 +443,7 @@ void evaluation(){
|
||||
}
|
||||
// When previous packet was a reset package -> enter program mode
|
||||
else if (reset_package_flag) {
|
||||
program_mode(number_of_bytes,byte_array,true);
|
||||
program_mode(number_of_bytes,byte_array);
|
||||
}
|
||||
// Check for reset package and set flag when reset package is received
|
||||
else {
|
||||
@@ -481,28 +484,30 @@ void track_signal_fall(unsigned int gpio, long unsigned int events) {
|
||||
}
|
||||
|
||||
|
||||
// Output initialization function - configures pwm frequency and clock divider according to CV_ARRAY_FLASH[]
|
||||
// Output initialization function - Configures pwm frequency and clock divider according to CV_111 - CV_171
|
||||
void init_outputs(){
|
||||
gpio_init_mask(GPIO_ALLOWED_OUTPUTS);
|
||||
gpio_set_dir_out_masked(GPIO_ALLOWED_OUTPUTS); //note: This might also disable UART on GPIO0 & GPIO1
|
||||
uint32_t Outputs_with_PWM_enabled = get_32bit_CV(111); // TODO: Verify - should be fine...
|
||||
gpio_set_dir_out_masked(GPIO_ALLOWED_OUTPUTS); // Note: This might also disable UART on GPIO0 & GPIO1
|
||||
uint32_t PWM_enabled_outputs = get_32bit_CV(111) & GPIO_ALLOWED_OUTPUTS;
|
||||
uint32_t slice, channel;
|
||||
uint16_t wrap, level;
|
||||
uint32_t temp_mask = 1;
|
||||
uint8_t clock_divider;
|
||||
uint32_t mask = 1;
|
||||
for (uint8_t i = 0; i < 32; ++i) {
|
||||
if (Outputs_with_PWM_enabled&temp_mask){
|
||||
if (PWM_enabled_outputs & mask){
|
||||
slice = pwm_gpio_to_slice_num(i);
|
||||
channel = pwm_gpio_to_channel(i); //0 for Channel A, 1 for Channel B
|
||||
wrap = get_16bit_CV(115 + slice*7); // TODO: Verify
|
||||
level = get_16bit_CV(118 + 7*slice+ 2*channel); // TODO: Verify
|
||||
channel = pwm_gpio_to_channel(i); // Channel A = "0"; Channel B = "1"
|
||||
wrap = get_16bit_CV(115 + 7*slice);
|
||||
level = get_16bit_CV(118 + 7*slice + 2*channel);
|
||||
clock_divider = CV_ARRAY_FLASH[117+7*slice] + 1;
|
||||
gpio_set_function(i,GPIO_FUNC_PWM);
|
||||
pwm_set_wrap(slice,wrap);
|
||||
pwm_set_gpio_level(i,0);
|
||||
level_table[i] = level;
|
||||
pwm_set_clkdiv_int_frac(slice,CV_ARRAY_FLASH[117+7*slice],0);
|
||||
pwm_set_clkdiv_int_frac(slice,clock_divider,0);
|
||||
pwm_set_enabled(slice,true);
|
||||
}
|
||||
temp_mask<<=1;
|
||||
mask<<=1;
|
||||
}
|
||||
}
|
||||
|
||||
@@ -514,25 +519,25 @@ uint16_t measure_base_pwm(bool direction, uint8_t iterations){
|
||||
else gpio = MOTOR_REV_PIN;
|
||||
float level_arr[iterations];
|
||||
for (int i = 0; i < iterations; ++i) {
|
||||
uint16_t level = 0;
|
||||
uint16_t max_level = (_125M/(CV_ARRAY_FLASH[8]*100+10000));
|
||||
uint16_t level = max_level/20;
|
||||
float measurement;
|
||||
do {
|
||||
pwm_set_gpio_level(gpio, level);
|
||||
busy_wait_ms(15);
|
||||
level += 10;
|
||||
level += max_level/500;
|
||||
measurement = measure(CV_ARRAY_FLASH[60],
|
||||
CV_ARRAY_FLASH[61],
|
||||
CV_ARRAY_FLASH[62],
|
||||
CV_ARRAY_FLASH[63],
|
||||
direction);
|
||||
}
|
||||
// (Measurement - ADC_Offset) < 5.0f
|
||||
while((measurement - (float)CV_ARRAY_FLASH[171]) < 5.0f);
|
||||
level_arr[i] = (float)level;
|
||||
busy_wait_ms(500);
|
||||
busy_wait_ms(100);
|
||||
}
|
||||
// Find and return overall average discarding outliers in measurement
|
||||
return (uint16_t)two_std_dev(level_arr,5);
|
||||
// Find and return overall average discarding outliers in measurement - multiply with 0.9
|
||||
return (uint16_t)(0.9f*two_std_dev(level_arr,5));
|
||||
}
|
||||
|
||||
|
||||
@@ -544,13 +549,13 @@ void cv_setup_check(){
|
||||
// Check for flash factory setting and set CV_FLASH_ARRAY to default values when factory condition is found.
|
||||
if ( CV_ARRAY_FLASH[64] ){
|
||||
uint8_t arr[4] = {125,8,7,124};
|
||||
program_mode(4,arr,false); //reset to CV_ARRAY_DEFAULT (write CV_8 = 8)
|
||||
program_mode(4,arr); //reset to CV_ARRAY_DEFAULT (write CV_8 = 8)
|
||||
}
|
||||
|
||||
// Check for adc offset setup
|
||||
if ( CV_ARRAY_FLASH[171] == 0xFF ){
|
||||
uint8_t arr[4] = {125,7,6,124};
|
||||
program_mode(4,arr,false); //ADC offset adjustment (write CV_7 = 7)
|
||||
program_mode(4,arr); //ADC offset adjustment (write CV_7 = 7)
|
||||
}
|
||||
|
||||
// Check for base PWM configuration - used for feed-forward
|
||||
@@ -560,9 +565,9 @@ void cv_setup_check(){
|
||||
uint8_t base_pwm_fwd_high_byte = base_pwm_fwd>>8;
|
||||
uint8_t base_pwm_fwd_low_byte = base_pwm_fwd&0x00FF;
|
||||
uint8_t arr0[4] = {125,base_pwm_fwd_high_byte,175,124};
|
||||
program_mode(4,arr0,false);
|
||||
program_mode(4,arr0);
|
||||
uint8_t arr1[4] = {125,base_pwm_fwd_low_byte,176,124};
|
||||
program_mode(4,arr1,false);
|
||||
program_mode(4,arr1);
|
||||
}
|
||||
// Reverse Direction
|
||||
if (get_16bit_CV(177) == 0){
|
||||
@@ -570,9 +575,9 @@ void cv_setup_check(){
|
||||
uint8_t base_pwm_rev_high_byte = base_pwm_rev>>8;
|
||||
uint8_t base_pwm_rev_low_byte = base_pwm_rev&0x00FF;
|
||||
uint8_t arr0[4] = {125,base_pwm_rev_high_byte,177,124};
|
||||
program_mode(4,arr0,false);
|
||||
program_mode(4,arr0);
|
||||
uint8_t arr1[4] = {125,base_pwm_rev_low_byte,178,124};
|
||||
program_mode(4,arr1,false);
|
||||
program_mode(4,arr1);
|
||||
}
|
||||
}
|
||||
|
||||
|
||||
Reference in new issue
Block a user