- Minor changes to variable names, comments & formatting

- Removed obsolete parameter previously used in program_mode
- Added correction constant regarding base pwm measurement
- Revised GPIO definitions (shared.h)
This commit is contained in:
1nct committed 2022-08-03 19:19:14 +02:00
1 parent bae6fff659
commit 0219963dd7
5 files changed
+106 -98

No files matched your search

+6 -8
View File
@@ -1,19 +1,18 @@
#pragma once
#define CV_ARRAY_SIZE 512
// All CVs are 8-bit numbers (range 0 - 255)
// All CVs are 8-bit numbers ranging from (0 - 255)dec ≙ (0b00000000 - 0b11111111)bin ≙ (0x00 - 0xFF)hex
// Note : CV_1 ≙ index 0, CV_2 ≙ index 1, CV_3 ≙ index 2, ...
// TODO: - Packet Timeout
uint8_t CV_ARRAY_DEFAULT [CV_ARRAY_SIZE] = {
0b00000011, //CV_1 - Basic address CV_1 = 0 is not allowed and used for initiating ADC offset adjustment //TODO: verify
0b00001000, //CV_2 - V_min - Default = 8
0b00000011, //CV_1 - Basic address - CV_1 = 0 and CV_1 > 127 are not valid - Default = 3
0b00001000, //CV_2 - V_min - Default = 8
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
// 0 == Fastest dec/acc rate; 255 == slowest;
0b00000000, //CV_3 - Acceleration rate - CV_3*CV_175 = Time for one discrete speed step change in ms
0b00000000, //CV_4 - Deceleration rate - CV_4*CV_175 = Time for one discrete speed step change in ms
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
0b01100100, //CV_5 - V_max - Default = 100*16
0b00111111, //CV_6 - V_mid - Default = 63*16
0b01100100, //CV_5 - V_max - Default = 100*16
0b00111111, //CV_6 - V_mid - Default = 63*16
0b00000001, //CV_7 - Version no. (read-only)
0b00001101, //CV_8 - Manufacturer (13 = Public Domain & Do-It-Yourself Decoders) (read-only)
0b10010110, //CV_9 - PWM frequency in Hz = CV_9*100+10000 - Default = (150*100+10000)Hz = 25kHz
@@ -135,7 +134,7 @@ uint8_t CV_ARRAY_DEFAULT [CV_ARRAY_SIZE] = {
// This Config can cause conflicts when GPIOs controlled by the same slice are enabled at the same time.
0b00000000, //CV_112 - GPIO 24-31 enable PWM
0b00000000, //CV_113 - GPIO 16-23 enable PWM
0b00111100, //CV_114 - GPIO 8-15 enable PWM
0b00000000, //CV_114 - GPIO 8-15 enable PWM
0b00000000, //CV_115 - GPIO 0-7 enable PWM
//Slice 0
0b00000000, //CV_116 - Wrap Bits 8-15
@@ -204,7 +203,6 @@ uint8_t CV_ARRAY_DEFAULT [CV_ARRAY_SIZE] = {
////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
//Offset adjustment for ADC //
//If CV_172 = 0xFF = 255 there will be a measurement procedure on startup //
//alternatively, the measurement can be done by writing a 0 to CV_1 on the programming track //
0b11111111, //CV_172 - ADC offset Default: 255 //
0b01111111, //CV_173 - ADC offset measurement cycles Default: 127 //
////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////