bump version to 2.0.17

NmraDcc.cpp

@@ -264,7 +264,10 @@
     static byte  ISRWatch;  // Interrupt Handler Edge Filter
 #elif defined ( ARDUINO_AVR_NANO_EVERY )
     static PinStatus ISREdge;	// Holder of the Next Edge we're looking for: RISING or FALLING
-#elif defined ( ARDUINO_ARCH_RP2040)
+#elif defined ( ARDUINO_ARCH_RP2040) 
+    static PinStatus ISREdge;	// Holder of the Next Edge we're looking for: RISING or FALLING
+    static byte  ISRWatch;  // Interrupt Handler Edge Filter
+#elif defined ( ARDUINO_ARCH_RENESAS_UNO) 
     static PinStatus ISREdge;	// Holder of the Next Edge we're looking for: RISING or FALLING
     static byte  ISRWatch;  // Interrupt Handler Edge Filter
 #else
@@ -680,7 +683,7 @@ DCC_PROCESSOR_STATE DccProcState ;
                 portENTER_CRITICAL_ISR (&mux);
                 #endif
                 DccRx.PacketCopy = DccRx.PacketBuf ;
-                DccRx.DataReady = 1 ;
+                DccRx.DataReady += 1 ;
                 #ifdef ESP32
                 portEXIT_CRITICAL_ISR (&mux);
                 #endif
@@ -809,7 +812,7 @@ void writeEEPROM (unsigned int CV, uint8_t Value)
 {
     EEPROM.write (CV, Value) ;
     
-	#if defined(ESP8266) || defined(ESP32)
+	#if defined(ESP8266)
 	noInterrupts();
 	#endif
 
@@ -817,7 +820,7 @@ void writeEEPROM (unsigned int CV, uint8_t Value)
     EEPROM.commit();
     #endif
     
-	#if defined(ESP8266) || defined(ESP32)
+	#if defined(ESP8266)
 	interrupts();
 	#endif
 }
@@ -1728,6 +1731,8 @@ void NmraDcc::setAccDecDCCAddrNextReceived (uint8_t enable)
 ////////////////////////////////////////////////////////////////////////
 uint8_t NmraDcc::process()
 {
+	uint8_t	copyDataReady ;
+	
     if (DccProcState.inServiceMode)
     {
         if ( (millis() - DccProcState.LastServiceModeMillis) > 20L)
@@ -1745,6 +1750,7 @@ uint8_t NmraDcc::process()
         noInterrupts();
         #endif
         Msg = DccRx.PacketCopy ;
+        copyDataReady = DccRx.DataReady;
         DccRx.DataReady = 0 ;
 
         #ifdef ESP32
@@ -1762,7 +1768,7 @@ uint8_t NmraDcc::process()
         if (notifyDccMsg) 	notifyDccMsg (&Msg);
 
         execDccProcessor (&Msg);
-        return 1 ;
+        return copyDataReady ;
     }
 
     return 0 ;

NmraDcc.h

@@ -127,7 +127,9 @@ typedef struct
     #define PRIO_DCC_IRQ    9
     #define PRIO_SYSTIC     8               // MUST be higher priority than DCC Irq
 #elif defined(ARDUINO_ARCH_RP2040)
-    #define MAXCV    256	     				    // todo: maybe somebody knows a good define for it
+    #define MAXCV    256	     			    // todo: maybe somebody knows a good define for it
+#elif defined ( ARDUINO_ARCH_RENESAS_UNO)
+    #define MAXCV	EEPROM.length()
 #elif defined(ARDUINO_SAMD_ZERO) 
     #define MAXCV    EEPROM_EMULATION_SIZE
 #else

examples/Fahrstuhl/Fahrstuhl.ino

@@ -17,7 +17,7 @@
 #define DCC_PIN 2
 
 // Define the DCC Turnout Address to select the first level = 1 
-#define DCC_ACCESSORY_DECODER_BASE_ADDRESS  200
+#define DCC_ACCESSORY_DECODER_BASE_ADDRESS  500
 
 // Define the manimus numbr of Levels
 #define NUM_LIFT_LEVELS  8
@@ -34,7 +34,7 @@
 #define BUTTON_LONG_PRESS_DELAY 2000
 
 // Uncomment ONE of the next 2 lines to enable AJS or UWE Board Settings
-//#define AJS_BOARD_SETTINGS
+// #define AJS_BOARD_SETTINGS
 #define UWE_BOARD_SETTINGS
 
 #if defined(AJS_BOARD_SETTINGS)  // Setting for AJS Dev System
@@ -267,9 +267,9 @@ elapsedMillis lastSpeedChange = 0;
   // The DCC Turnout Address is checked to see if it is within the range used to Select Elevator levels and starts a Move if a new level is selected 
 void notifyDccAccTurnoutOutput(uint16_t receivedAddress, uint8_t direction, uint8_t outputPower)
 {
-  if((receivedAddress >= DCC_ACCESSORY_DECODER_BASE_ADDRESS) && (receivedAddress < (DCC_ACCESSORY_DECODER_BASE_ADDRESS + NUM_LIFT_LEVELS)))
+  if((receivedAddress >= DCC_ACCESSORY_DECODER_BASE_ADDRESS) && (receivedAddress < (DCC_ACCESSORY_DECODER_BASE_ADDRESS + (NUM_LIFT_LEVELS/2))))
   {
-    uint8_t newLevel = receivedAddress - DCC_ACCESSORY_DECODER_BASE_ADDRESS;
+    uint8_t newLevel = (receivedAddress - DCC_ACCESSORY_DECODER_BASE_ADDRESS) * 2 + direction;
     if(persistentValues.lastLiftLevel != newLevel)
     {
       persistentValues.lastLiftLevel = newLevel;

library.properties

@@ -1,5 +1,5 @@
 name=NmraDcc
-version=2.0.15
+version=2.0.17
 author=Alex Shepherd, Wolfgang Kuffer, Geoff Bunza, Martin Pischky, Franz-Peter Müller, Sven (littleyoda), Hans Tanner, bugfixes by Jueff
 maintainer=Alex Shepherd <kiwi64ajs@gmail.com>
 sentence=Enables NMRA DCC Communication