Delete Dec_2Mot_4LED_Aud_8Ftn.ino
This commit is contained in:
Geoff Bunza
GitHub
@@ -1,669 +0,0 @@
|
||||
// Production 2 Motor w/Audio 13 Function DCC Decoder Dec_2Mot_10LED_Audio_8Ftn.ino
|
||||
// Version 6.01 Geoff Bunza 2014,2015,2016,2017,2018
|
||||
// Now works with both short and long DCC Addesses
|
||||
|
||||
// NO LONGER REQUIRES modified software servo Lib
|
||||
// Software restructuring mods added from Alex Shepherd and Franz-Peter
|
||||
// With sincere thanks
|
||||
/*
|
||||
* Motor selection is via motor select Function 13 (Motor1) and Function 14 (Motor2)
|
||||
* Motor speed for each can only be changed if the corresponding Function is on
|
||||
* (F13 and/or F14). Motor speed is maintained if the corresponding Motor select function
|
||||
* is off. Thus, each motor can be controlled independently and run at different speeds.
|
||||
* F0 LED Pin 8
|
||||
* F1-F6 6 Functions Configures As Audio Play
|
||||
* F7-F9 3 Functions Configures As LEDs
|
||||
* F13 Motor1 Control Enable
|
||||
* F14 Motor2 Control Enable
|
||||
* Pro Mini Transmit-7 (TX) connected to DFPlayer Receive (RX)Pin 2 via 470 Ohm Resistor
|
||||
* Pro Mini Receive (RX) connected to DFPlayer Transmit (TX) Pin 3
|
||||
* Remember to connect +5V and GND to the DFPlayer too: DFPLAYER PINS 1 & 7,10 respectively
|
||||
* This is a “mobile/function” decoder that adds audio play to dual motor control and
|
||||
* LED functions. Audio tracks or clips are stored on a micro SD card for playing,
|
||||
* in a folder labeled mp3, with tracks named 0001.mp3, 0002.mp3, etc. F0 is configured
|
||||
* as an on/off LED function, F1-F5 play audio tracks 1-5 respectively.
|
||||
* F6 plays a random selection in random order from tracks 1-6.
|
||||
* F7-F9 control LEDs on Pro Mini Digital Pins 11-13.
|
||||
* Simple speed control is made via throttle speed setting for two motors. Motor selection
|
||||
* is via motor select Function 13 (Motor1) and Function 14 (Motor2). Motor speed for each
|
||||
* can only be changed if the corresponding Function is on (F13 and/or F14). Motor speed is
|
||||
* maintained if the corresponding motor select function is off. Thus, each motor can be
|
||||
* controlled independently and run at different speeds. The other functions are configurable
|
||||
* but are preset for LED on/off control.
|
||||
*/
|
||||
// ******** UNLESS YOU WANT ALL CV'S RESET UPON EVERY POWER UP
|
||||
// ******** AFTER THE INITIAL DECODER LOAD REMOVE THE "//" IN THE FOOLOWING LINE!!
|
||||
//#define DECODER_LOADED
|
||||
|
||||
// ******** EMOVE THE "//" IN THE FOOLOWING LINE TO SEND DEBUGGING
|
||||
// ******** INFO TO THE SERIAL MONITOR
|
||||
//#define DEBUG
|
||||
|
||||
#include <NmraDcc.h>
|
||||
#include <SoftwareServo.h>
|
||||
#include <SoftwareSerial.h>
|
||||
#include <DFPlayer_Mini_Mp3.h>
|
||||
SoftwareSerial mySerial(6,7); // PRO MINI RX, PRO MINI TX serial to DFPlayer
|
||||
|
||||
int busy_pin = 5; // DFPlayer Busy status pin
|
||||
#define num_clips 6 //number of sound tracks/clips on the Micro SD Memory Card
|
||||
int del_tim = 4000;
|
||||
int tctr, tctr2, i;
|
||||
byte audio_on = 0; // Audio ON sets this to 1; otherwise 0
|
||||
|
||||
SoftwareServo servo[10];
|
||||
#define servo_start_delay 50
|
||||
#define servo_init_delay 7
|
||||
#define servo_slowdown 4 //servo loop counter limit
|
||||
int servo_slow_counter = 0; //servo loop counter to slowdown servo transit
|
||||
|
||||
uint8_t Motor1Speed = 0;
|
||||
uint8_t Motor1ForwardDir = 1;
|
||||
uint8_t Motor1MaxSpeed = 127;
|
||||
uint8_t Motor2Speed = 0;
|
||||
uint8_t Motor2ForwardDir = 1;
|
||||
uint8_t Motor2MaxSpeed = 127;
|
||||
int kickstarton = 1400; //kick start cycle on time
|
||||
int kickstarttime = 5; //kick start duration on time
|
||||
int fwdon = 0;
|
||||
int fwdtime = 1;
|
||||
int bwdon = 0;
|
||||
int bwdtime = 1;
|
||||
int bwdshift = 0;
|
||||
int cyclewidth = 2047;
|
||||
int m2h = 3; //R H Bridge //Motor1
|
||||
int m2l = 4; //B H Bridge //Motor1
|
||||
int m0h = 9; //R H Bridge //Motor2
|
||||
int m0l = 10; //B H Bridge //Motor2
|
||||
|
||||
int speedup = 112; //Right track time differntial
|
||||
int deltime = 1500;
|
||||
int tim_delay = 100;
|
||||
int numfpins = 14;
|
||||
int num_active_fpins = 10;
|
||||
byte fpins [] = {3,4,8,9,10,11,12,13,14,15,16,17,18,19};
|
||||
const int FunctionPin0 = 8;
|
||||
const int FunctionPin1 = 11;
|
||||
const int FunctionPin2 = 12;
|
||||
const int FunctionPin3 = 13;
|
||||
const int FunctionPin4 = 14; //A0
|
||||
|
||||
const int FunctionPin5 = 15; //A1
|
||||
const int FunctionPin6 = 16; //A2
|
||||
const int FunctionPin7 = 17; //A3
|
||||
const int FunctionPin8 = 18; //A4
|
||||
const int FunctionPin9 = 19; //A5
|
||||
|
||||
const int FunctionPin10 = 20; // Place holders ONLY
|
||||
const int FunctionPin11 = 20;
|
||||
const int FunctionPin12 = 20;
|
||||
const int FunctionPin13 = 20;
|
||||
const int FunctionPin14 = 20;
|
||||
const int FunctionPin15 = 20;
|
||||
const int FunctionPin16 = 20;
|
||||
|
||||
int Function13_value = 0;
|
||||
int Function14_value = 0;
|
||||
|
||||
NmraDcc Dcc ;
|
||||
DCC_MSG Packet ;
|
||||
uint8_t CV_DECODER_MASTER_RESET = 120;
|
||||
int t; // temp
|
||||
|
||||
struct QUEUE
|
||||
{
|
||||
int inuse;
|
||||
int current_position;
|
||||
int increment;
|
||||
int stop_value;
|
||||
int start_value;
|
||||
};
|
||||
QUEUE *ftn_queue = new QUEUE[17];
|
||||
|
||||
struct CVPair
|
||||
{
|
||||
uint16_t CV;
|
||||
uint8_t Value;
|
||||
};
|
||||
|
||||
#define This_Decoder_Address 24
|
||||
|
||||
CVPair FactoryDefaultCVs [] =
|
||||
{
|
||||
{CV_MULTIFUNCTION_PRIMARY_ADDRESS, This_Decoder_Address&0x7F },
|
||||
|
||||
// These two CVs define the Long DCC Address
|
||||
{CV_MULTIFUNCTION_EXTENDED_ADDRESS_MSB, ((This_Decoder_Address>>8)&0x7F)+192 },
|
||||
{CV_MULTIFUNCTION_EXTENDED_ADDRESS_LSB, This_Decoder_Address&0xFF },
|
||||
|
||||
// ONLY uncomment 1 CV_29_CONFIG line below as approprate DEFAULT IS SHORT ADDRESS
|
||||
// {CV_29_CONFIG, 0}, // Short Address 14 Speed Steps
|
||||
{CV_29_CONFIG, CV29_F0_LOCATION}, // Short Address 28/128 Speed Steps
|
||||
// {CV_29_CONFIG, CV29_EXT_ADDRESSING | CV29_F0_LOCATION}, // Long Address 28/128 Speed Steps
|
||||
|
||||
{CV_DECODER_MASTER_RESET, 0},
|
||||
{30, 0}, //F0 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade,6=Audio
|
||||
{31, 10}, //F0 Rate Blink=Eate,PWM=Rate,Servo=Rate,Audio=Volume(0-30)
|
||||
{32, 0}, //F0 Start Position F0=0,Audio=Audio Track/Clip#
|
||||
{33, 8}, //F0 End Position F0=1
|
||||
{34, 1}, //F0 Current Position
|
||||
{35, 6}, //F1 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade,6=Audio
|
||||
{36, 22}, // Rate Blink=Eate,PWM=Rate,Servo=Rate,Audio=Volume(0-30)
|
||||
{37, 1}, // Start Position Fx=0,Audio=Audio Track/Clip#
|
||||
{38, 8}, // End Position Fx=1
|
||||
{39, 1}, // Current Position
|
||||
{40, 6}, //F2 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade,6=Audio
|
||||
{41, 22}, // Rate Blink=Eate,PWM=Rate,Servo=Rate,Audio=Volume(0-30)
|
||||
{42, 2}, // Start Position Fx=0,Audio=Audio Track/Clip#
|
||||
{43, 140}, // End Position Fx=1
|
||||
{44, 0}, // Current Position
|
||||
{45, 6}, //F3 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade,6=Audio
|
||||
{46, 22}, // Rate Blink=Eate,PWM=Rate,Servo=Rate,Audio=Volume(0-30)
|
||||
{47, 3}, // Start Position Fx=0,Audio=Audio Track/Clip#
|
||||
{48, 140}, // End Position Fx=1
|
||||
{49, 0}, // Current Position
|
||||
{50, 6}, //F4 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade,6=Audio
|
||||
{51, 22}, // Rate Blink=Eate,PWM=Rate,Servo=Rate,Audio=Volume(0-30)
|
||||
{52, 4}, // Start Position Fx=0,Audio=Audio Track/Clip#
|
||||
{53, 140}, // End Position Fx=1
|
||||
{54, 0}, // Current Position
|
||||
{55, 6}, //F5 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade,6=Audio
|
||||
{56, 22}, // Rate Blink=Eate,PWM=Rate,Servo=Rate,Audio=Volume(0-30)
|
||||
{57, 5}, // Start Position Fx=0,Audio=Audio Track/Clip#
|
||||
{58, 140}, // End Position Fx=1
|
||||
{59, 28}, // Current Position
|
||||
{60, 7}, //F6 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade,6=Audio
|
||||
{61, 22}, // Rate Blink=Eate,PWM=Rate,Servo=Rate,Audio=Volume(0-30)
|
||||
{62, 6}, // Start Position Fx=0,Audio=Audio Track/Clip#
|
||||
{63, 140}, // End Position Fx=1
|
||||
{64, 28}, // Current Position
|
||||
{65, 0}, //F7 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade,6=Audio
|
||||
{66, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate,Audio=Volume(0-30)
|
||||
{67, 28}, // Start Position Fx=0,Audio=Audio Track/Clip#
|
||||
{68,140}, // End Position Fx=1
|
||||
{69, 28}, // Current Position
|
||||
{70, 0}, //F8 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade,6=Audio
|
||||
{71, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate,Audio=Volume(0-30)
|
||||
{72, 28}, // Start Position Fx=0,Audio=Audio Track/Clip#
|
||||
{73, 140}, // End Position Fx=1
|
||||
{74, 28}, // Current Position
|
||||
{75, 0}, //F9 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade,6=Audio
|
||||
{76, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate,Audio=Volume(0-30)
|
||||
{77, 28}, // Start Position Fx=0,Audio=Audio Track/Clip#
|
||||
{78, 140}, // End Position Fx=1
|
||||
{79, 28}, // Current Position
|
||||
};
|
||||
|
||||
uint8_t FactoryDefaultCVIndex = sizeof(FactoryDefaultCVs)/sizeof(CVPair);
|
||||
void notifyCVResetFactoryDefault()
|
||||
{
|
||||
// Make FactoryDefaultCVIndex non-zero and equal to num CV's to be reset
|
||||
// to flag to the loop() function that a reset to Factory Defaults needs to be done
|
||||
FactoryDefaultCVIndex = sizeof(FactoryDefaultCVs)/sizeof(CVPair);
|
||||
};
|
||||
|
||||
// NOTE: NO PROGRAMMING ACK IS SET UP TO MAXIMAIZE
|
||||
// OUTPUT PINS FOR FUNCTIONS
|
||||
|
||||
void setup() //******************************************************
|
||||
{
|
||||
#ifdef DEBUG
|
||||
Serial.begin(115200);
|
||||
#endif
|
||||
pinMode (busy_pin, INPUT);
|
||||
mySerial.begin (9600);
|
||||
mp3_set_serial (mySerial); //set softwareSerial for DFPlayer-mini mp3 module
|
||||
mp3_reset ();
|
||||
delay(100);
|
||||
mp3_set_volume (18);
|
||||
delay(50);
|
||||
audio_on = 0;
|
||||
uint8_t cv_value;
|
||||
// initialize the digital pins as outputs
|
||||
for (int i=0; i < numfpins; i++) {
|
||||
pinMode(fpins[i], OUTPUT);
|
||||
digitalWrite(fpins[i], 0);
|
||||
}
|
||||
// Setup which External Interrupt, the Pin it's associated with that we're using
|
||||
Dcc.pin(0, 2, 0);
|
||||
// Call the main DCC Init function to enable the DCC Receiver
|
||||
Dcc.init( MAN_ID_DIY, 601, FLAGS_MY_ADDRESS_ONLY, 0 );
|
||||
delay(800);
|
||||
|
||||
#if defined(DECODER_LOADED)
|
||||
if ( Dcc.getCV(CV_DECODER_MASTER_RESET)== CV_DECODER_MASTER_RESET )
|
||||
#endif
|
||||
|
||||
{
|
||||
for (int j=0; j < FactoryDefaultCVIndex; j++ )
|
||||
Dcc.setCV( FactoryDefaultCVs[j].CV, FactoryDefaultCVs[j].Value);
|
||||
digitalWrite(fpins[14], 1);
|
||||
delay (1000);
|
||||
digitalWrite(fpins[14], 0);
|
||||
}
|
||||
for ( i=0; i < num_active_fpins; i++) {
|
||||
cv_value = Dcc.getCV( 30+(i*5)) ;
|
||||
#ifdef DEBUG
|
||||
Serial.print(" cv_value: ");
|
||||
Serial.println(cv_value, DEC) ;
|
||||
#endif
|
||||
switch ( cv_value ) {
|
||||
case 0: // LED on/off
|
||||
ftn_queue[i].inuse = 0;
|
||||
break;
|
||||
case 1: // LED Blink
|
||||
{
|
||||
ftn_queue[i].inuse = 0;
|
||||
ftn_queue[i].current_position = 0;
|
||||
ftn_queue[i].start_value = 0;
|
||||
ftn_queue[i].increment = int (char (Dcc.getCV( 31+(i*5))));
|
||||
digitalWrite(fpins[i], 0);
|
||||
ftn_queue[i].stop_value = int(Dcc.getCV( 33+(i*5))) ;
|
||||
}
|
||||
break;
|
||||
case 2: //servo
|
||||
{
|
||||
ftn_queue[i].current_position =int (Dcc.getCV( 34+(i*5)));
|
||||
ftn_queue[i].stop_value = int (Dcc.getCV( 33+(i*5)));
|
||||
ftn_queue[i].start_value = int (Dcc.getCV( 32+(i*5)));
|
||||
ftn_queue[i].increment = -int (char (Dcc.getCV( 31+(i*5))));
|
||||
// attaches servo on pin to the servo object
|
||||
servo[i].attach(fpins[i]);
|
||||
|
||||
#ifdef DEBUG
|
||||
Serial.print("InitServo ID= ");
|
||||
Serial.println(i, DEC) ;
|
||||
#endif
|
||||
servo[i].write(ftn_queue[i].start_value);
|
||||
for (t=0; t<servo_start_delay; t++)
|
||||
{SoftwareServo::refresh();delay(servo_init_delay);}
|
||||
ftn_queue[i].inuse = 0;
|
||||
servo[i].detach();
|
||||
}
|
||||
break;
|
||||
case 3: // DOUBLE ALTERNATING LED Blink
|
||||
{
|
||||
ftn_queue[i].inuse = 0;
|
||||
ftn_queue[i].current_position = 0;
|
||||
ftn_queue[i].start_value = 0;
|
||||
ftn_queue[i].increment = Dcc.getCV( 31+(i*5));
|
||||
digitalWrite(fpins[i], 0);
|
||||
digitalWrite(fpins[i+1], 0);
|
||||
ftn_queue[i].stop_value = int(Dcc.getCV( 33+(i*5)));
|
||||
}
|
||||
break;
|
||||
case 4: // Simple Pulsed Output based on saved Rate =10*Rate in Milliseconds
|
||||
{
|
||||
ftn_queue[i].inuse = 0;
|
||||
ftn_queue[i].current_position = 0;
|
||||
ftn_queue[i].increment = 10 * int (char (Dcc.getCV( 31+(i*5))));
|
||||
digitalWrite(fpins[i], 0);
|
||||
}
|
||||
break;
|
||||
case 5: // Fade On
|
||||
{
|
||||
ftn_queue[i].inuse = 0;
|
||||
ftn_queue[i].start_value = 0;
|
||||
ftn_queue[i].increment = int (char (Dcc.getCV( 31+(i*5))));
|
||||
digitalWrite(fpins[i], 0);
|
||||
ftn_queue[i].stop_value = int(Dcc.getCV( 33+(i*5))) *10.;
|
||||
}
|
||||
break;
|
||||
case 6: // Audio Track Play
|
||||
ftn_queue[i].inuse = 0;
|
||||
ftn_queue[i].increment = int (char (Dcc.getCV( 31+(i*5))));
|
||||
ftn_queue[i].start_value = int (Dcc.getCV( 32+(i*5)));
|
||||
audio_on = 0;
|
||||
break;
|
||||
case 7: // Audio Random Track Play
|
||||
ftn_queue[i].inuse = 0;
|
||||
ftn_queue[i].increment = int (char (Dcc.getCV( 31+(i*5))));
|
||||
ftn_queue[i].start_value = int (Dcc.getCV( 32+(i*5)));
|
||||
audio_on = 0;
|
||||
break;
|
||||
case 8: // NEXT FEATURE to pin
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
void loop() //**********************************************************************
|
||||
{
|
||||
//MUST call the NmraDcc.process() method frequently
|
||||
// from the Arduino loop() function for correct library operation
|
||||
Dcc.process();
|
||||
SoftwareServo::refresh();
|
||||
delay(2);
|
||||
if (Motor1Speed != 0) {
|
||||
if (Motor1ForwardDir == 0) gofwd1 (fwdtime, int((Motor1Speed&0x7f)*21));
|
||||
else gobwd1 (bwdtime, int((Motor1Speed&0x7f)*21));
|
||||
}
|
||||
if (Motor2Speed != 0) {
|
||||
if (Motor2ForwardDir == 0) gofwd2 (fwdtime, int((Motor2Speed&0x7f)*21));
|
||||
else gobwd2 (bwdtime, int((Motor2Speed&0x7f)*21));
|
||||
}
|
||||
//
|
||||
for (int i=0; i < num_active_fpins; i++) {
|
||||
if (ftn_queue[i].inuse==1) {
|
||||
|
||||
switch (Dcc.getCV( 30+(i*5))) {
|
||||
case 0:
|
||||
break;
|
||||
case 1:
|
||||
ftn_queue[i].current_position = ftn_queue[i].current_position + ftn_queue[i].increment;
|
||||
if (ftn_queue[i].current_position > ftn_queue[i].stop_value) {
|
||||
ftn_queue[i].start_value = ~ftn_queue[i].start_value;
|
||||
digitalWrite(fpins[i], ftn_queue[i].start_value);
|
||||
ftn_queue[i].current_position = 0;
|
||||
ftn_queue[i].stop_value = int(Dcc.getCV( 33+(i*5)));
|
||||
}
|
||||
break;
|
||||
case 2:
|
||||
{
|
||||
if (servo_slow_counter++ > servo_slowdown)
|
||||
{
|
||||
ftn_queue[i].current_position = ftn_queue[i].current_position + ftn_queue[i].increment;
|
||||
if (ftn_queue[i].increment > 0) {
|
||||
if (ftn_queue[i].current_position > ftn_queue[i].stop_value) {
|
||||
ftn_queue[i].current_position = ftn_queue[i].stop_value;
|
||||
ftn_queue[i].inuse = 0;
|
||||
servo[i].detach();
|
||||
}
|
||||
}
|
||||
if (ftn_queue[i].increment < 0) {
|
||||
if (ftn_queue[i].current_position < ftn_queue[i].start_value) {
|
||||
ftn_queue[i].current_position = ftn_queue[i].start_value;
|
||||
ftn_queue[i].inuse = 0;
|
||||
servo[i].detach();
|
||||
}
|
||||
}
|
||||
servo[i].write(ftn_queue[i].current_position);
|
||||
servo_slow_counter = 0;
|
||||
}
|
||||
}
|
||||
break;
|
||||
case 3:
|
||||
ftn_queue[i].current_position = ftn_queue[i].current_position + ftn_queue[i].increment;
|
||||
if (ftn_queue[i].current_position > ftn_queue[i].stop_value) {
|
||||
ftn_queue[i].start_value = ~ftn_queue[i].start_value;
|
||||
digitalWrite(fpins[i], ftn_queue[i].start_value);
|
||||
digitalWrite(fpins[i]+1, ~ftn_queue[i].start_value);
|
||||
ftn_queue[i].current_position = 0;
|
||||
ftn_queue[i].stop_value = int(Dcc.getCV( 33+(i*5)));
|
||||
}
|
||||
i++;
|
||||
break;
|
||||
case 4: // Simple Pulsed Output based on saved Rate =10*Rate in Milliseconds
|
||||
{
|
||||
ftn_queue[i].inuse = 0;
|
||||
ftn_queue[i].current_position = 0;
|
||||
ftn_queue[i].increment = 10 * int (char (Dcc.getCV( 31+(i*5))));
|
||||
digitalWrite(fpins[i], 0);
|
||||
}
|
||||
break;
|
||||
case 5: // Fade On
|
||||
|
||||
break;
|
||||
case 6: // Audio Track Play
|
||||
if (digitalRead(busy_pin)== HIGH) {
|
||||
ftn_queue[i].inuse = 0;
|
||||
}
|
||||
break;
|
||||
case 7: // Audio Random Track/Clip Play
|
||||
if (digitalRead(busy_pin)== HIGH) {
|
||||
ftn_queue[i].inuse = 0;
|
||||
/* Insert the following code if you want continuous random play as long as F6 is selected
|
||||
if (ftn_queue[i].inuse ==1) { // Audio Off continue playing clips
|
||||
mp3_play (random(1,num_clips)); // play random clip
|
||||
delay(5);
|
||||
}
|
||||
*/
|
||||
}
|
||||
break;
|
||||
case 8: // NEXT FEATURE to pin
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
}
|
||||
}
|
||||
}
|
||||
void gofwd1(int fcnt,int fcycle) {
|
||||
int icnt;
|
||||
int totcycle;
|
||||
icnt = 0;
|
||||
while (icnt < fcnt)
|
||||
{
|
||||
digitalWrite(m2h, HIGH); //Motor1
|
||||
delayMicroseconds(fcycle);
|
||||
digitalWrite(m2h, LOW); //Motor1
|
||||
delayMicroseconds(cyclewidth - fcycle);
|
||||
icnt++;
|
||||
}
|
||||
}
|
||||
void gobwd1(int bcnt,int bcycle) {
|
||||
int icnt;
|
||||
icnt=0;
|
||||
while (icnt < bcnt)
|
||||
{
|
||||
digitalWrite(m2l, HIGH); //Motor1
|
||||
delayMicroseconds(bcycle);
|
||||
digitalWrite(m2l, LOW); //Motor1
|
||||
delayMicroseconds(cyclewidth - bcycle);
|
||||
icnt++;
|
||||
}
|
||||
}
|
||||
void gofwd2(int fcnt,int fcycle) {
|
||||
int icnt;
|
||||
int totcycle;
|
||||
icnt = 0;
|
||||
while (icnt < fcnt)
|
||||
{
|
||||
digitalWrite(m0h, HIGH); //Motor2
|
||||
delayMicroseconds(fcycle);
|
||||
digitalWrite(m0h, LOW); //Motor2
|
||||
delayMicroseconds(cyclewidth - fcycle);
|
||||
icnt++;
|
||||
}
|
||||
}
|
||||
void gobwd2(int bcnt,int bcycle) {
|
||||
int icnt;
|
||||
icnt=0;
|
||||
while (icnt < bcnt)
|
||||
{
|
||||
digitalWrite(m0l, HIGH); //Motor2
|
||||
delayMicroseconds(bcycle);
|
||||
digitalWrite(m0l, LOW); //Motor2
|
||||
delayMicroseconds(cyclewidth - bcycle);
|
||||
icnt++;
|
||||
}
|
||||
}
|
||||
void notifyDccSpeed( uint16_t Addr, DCC_ADDR_TYPE AddrType, uint8_t Speed, DCC_DIRECTION ForwardDir, DCC_SPEED_STEPS SpeedSteps ) {
|
||||
if (Function13_value==1) {
|
||||
Motor1Speed = Speed;
|
||||
Motor1ForwardDir = ForwardDir;
|
||||
}
|
||||
if (Function14_value==1) {
|
||||
Motor2Speed = Speed;
|
||||
Motor2ForwardDir = ForwardDir;
|
||||
}
|
||||
}
|
||||
|
||||
void notifyDccFunc( uint16_t Addr, DCC_ADDR_TYPE AddrType, FN_GROUP FuncGrp, uint8_t FuncState) {
|
||||
#ifdef DEBUG
|
||||
Serial.print("Addr= ");
|
||||
Serial.println(Addr, DEC) ;
|
||||
Serial.print("FuncState= ");
|
||||
Serial.println(FuncState, DEC) ;
|
||||
#endif
|
||||
switch(FuncGrp)
|
||||
{
|
||||
case FN_0_4: //Function Group 1 F0 F4 F3 F2 F1
|
||||
exec_function( 0, FunctionPin0, (FuncState & FN_BIT_00)>>4 );
|
||||
exec_function( 1, FunctionPin1, (FuncState & FN_BIT_01));
|
||||
exec_function( 2, FunctionPin2, (FuncState & FN_BIT_02)>>1);
|
||||
exec_function( 3, FunctionPin3, (FuncState & FN_BIT_03)>>2 );
|
||||
exec_function( 4, FunctionPin4, (FuncState & FN_BIT_04)>>3 );
|
||||
break;
|
||||
|
||||
case FN_5_8: //Function Group 1 S FFFF == 1 F8 F7 F6 F5 & == 0 F12 F11 F10 F9 F8
|
||||
exec_function( 5, FunctionPin5, (FuncState & FN_BIT_05));
|
||||
exec_function( 6, FunctionPin6, (FuncState & FN_BIT_06)>>1 );
|
||||
exec_function( 7, FunctionPin7, (FuncState & FN_BIT_07)>>2 );
|
||||
exec_function( 8, FunctionPin8, (FuncState & FN_BIT_08)>>3 );
|
||||
break;
|
||||
|
||||
case FN_9_12:
|
||||
exec_function( 9, FunctionPin9, (FuncState & FN_BIT_09));
|
||||
// exec_function( 10, FunctionPin10, (FuncState & FN_BIT_10)>>1 );
|
||||
// exec_function( 11, FunctionPin11, (FuncState & FN_BIT_11)>>2 );
|
||||
// exec_function( 12, FunctionPin12, (FuncState & FN_BIT_12)>>3 );
|
||||
break;
|
||||
|
||||
case FN_13_20: //Function Group 2 FuncState == F20-F13 Function Control
|
||||
Function13_value = (FuncState & FN_BIT_13);
|
||||
Function14_value = (FuncState & FN_BIT_14)>>1;
|
||||
// exec_function( 15, FunctionPin15, (FuncState & FN_BIT_15)>>2 );
|
||||
// exec_function( 16, FunctionPin16, (FuncState & FN_BIT_16)>>3 );
|
||||
break;
|
||||
|
||||
case FN_21_28:
|
||||
break;
|
||||
}
|
||||
}
|
||||
void exec_function (int function, int pin, int FuncState) {
|
||||
switch ( Dcc.getCV( 30+(function*5)) ) { // Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
case 0: // On - Off LED
|
||||
digitalWrite (pin, FuncState);
|
||||
ftn_queue[function].inuse = 0;
|
||||
break;
|
||||
case 1: // Blinking LED
|
||||
if ((ftn_queue[function].inuse==0) && (FuncState==1)) {
|
||||
ftn_queue[function].inuse = 1;
|
||||
ftn_queue[function].start_value = 0;
|
||||
digitalWrite(pin, 0);
|
||||
ftn_queue[function].stop_value = int(Dcc.getCV( 33+(function*5)));
|
||||
} else {
|
||||
if ((ftn_queue[function].inuse==1) && (FuncState==0)) {
|
||||
ftn_queue[function].inuse = 0;
|
||||
digitalWrite(pin, 0);
|
||||
}
|
||||
}
|
||||
break;
|
||||
case 2: // Servo
|
||||
if (ftn_queue[function].inuse == 0) {
|
||||
ftn_queue[function].inuse = 1;
|
||||
servo[function].attach(pin);
|
||||
}
|
||||
if (FuncState==1) ftn_queue[function].increment = char ( Dcc.getCV( 31+(function*5)));
|
||||
else ftn_queue[function].increment = - char(Dcc.getCV( 31+(function*5)));
|
||||
if (FuncState==1) ftn_queue[function].stop_value = Dcc.getCV( 33+(function*5));
|
||||
else ftn_queue[function].stop_value = Dcc.getCV( 32+(function*5));
|
||||
break;
|
||||
case 3: // Blinking LED PAIR
|
||||
if ((ftn_queue[function].inuse==0) && (FuncState==1)) {
|
||||
ftn_queue[function].inuse = 1;
|
||||
ftn_queue[function].start_value = 0;
|
||||
digitalWrite(fpins[function], 0);
|
||||
digitalWrite(fpins[function+1], 1);
|
||||
ftn_queue[function].stop_value = int(Dcc.getCV( 33+(function*5)));
|
||||
} else {
|
||||
if (FuncState==0) {
|
||||
ftn_queue[function].inuse = 0;
|
||||
digitalWrite(fpins[function], 0);
|
||||
digitalWrite(fpins[function+1], 0);
|
||||
}
|
||||
}
|
||||
break;
|
||||
case 4: // Pulse Output based on Rate*10 Milliseconds
|
||||
if ((ftn_queue[function].inuse==0) && (FuncState==1)) { //First Turn On Detected
|
||||
digitalWrite(fpins[function], 1);
|
||||
delay (10*ftn_queue[function].increment);
|
||||
digitalWrite(fpins[function], 0);
|
||||
ftn_queue[function].inuse = 1; //inuse set to 1 says we already pulsed
|
||||
} else
|
||||
if (FuncState==0) ftn_queue[function].inuse = 0;
|
||||
break;
|
||||
case 5: // Fade On
|
||||
#define fadedelay 24
|
||||
if ((ftn_queue[function].inuse==0) && (FuncState==1)) {
|
||||
ftn_queue[function].inuse = 1;
|
||||
for (t=0; t<ftn_queue[function].stop_value; t+=ftn_queue[function].increment) {
|
||||
digitalWrite( fpins[function], 1);
|
||||
delay(fadedelay*(t/(1.*ftn_queue[function].stop_value)));
|
||||
digitalWrite( fpins[function], 0);
|
||||
delay(fadedelay-(fadedelay*(t/(1.*ftn_queue[function].stop_value))));
|
||||
}
|
||||
digitalWrite( fpins[function], 1 );
|
||||
} else {
|
||||
if ((ftn_queue[function].inuse==1) && (FuncState==0)) {
|
||||
ftn_queue[function].inuse = 0;
|
||||
digitalWrite(fpins[function], 0);
|
||||
}
|
||||
}
|
||||
break;
|
||||
|
||||
case 6: // Audio Play
|
||||
#ifdef DEBUG
|
||||
Serial.print("function= ");
|
||||
Serial.println(function, DEC) ;
|
||||
Serial.print("FuncState= ");
|
||||
Serial.println(FuncState, DEC) ;
|
||||
#endif
|
||||
if ((digitalRead(busy_pin)==HIGH)&&(FuncState!=0)) { // Audio Off = Not Playing
|
||||
ftn_queue[function].inuse = 1;
|
||||
mp3_set_volume (ftn_queue[function].increment);
|
||||
delay(8);
|
||||
mp3_play (ftn_queue[function].start_value); // play clip function
|
||||
delay(5);
|
||||
}
|
||||
if ((digitalRead(busy_pin)==LOW)&&(FuncState==0)) { // Audio On = Playing
|
||||
ftn_queue[function].inuse = 0; // Fuunction turned off so get ready to stop
|
||||
}
|
||||
break;
|
||||
case 7: // Random Audio Function
|
||||
#ifdef DEBUG
|
||||
Serial.print("function= ");
|
||||
Serial.println(function, DEC) ;
|
||||
Serial.print("FuncState= ");
|
||||
Serial.println(FuncState, DEC) ;
|
||||
#endif
|
||||
if ((digitalRead(busy_pin)==HIGH)&&(FuncState!=0)) { // Audio Off = Not Playing
|
||||
ftn_queue[function].inuse = 1;
|
||||
mp3_set_volume (ftn_queue[function].increment);
|
||||
delay(8);
|
||||
mp3_play (random(1,num_clips+1)); // play random clip
|
||||
delay(5);
|
||||
}
|
||||
if ((digitalRead(busy_pin)==LOW)&&(FuncState==0)) { // Audio On = Playing
|
||||
ftn_queue[function].inuse = 0; // Fuunction turned off so get ready to stop
|
||||
}
|
||||
break;
|
||||
default:
|
||||
ftn_queue[function].inuse = 0;
|
||||
break;
|
||||
}
|
||||
}
|
||||
/*
|
||||
mp3_play (); //start play
|
||||
mp3_play (5); //play "mp3/0005.mp3"
|
||||
mp3_next (); //play next
|
||||
mp3_prev (); //play previous
|
||||
mp3_set_volume (uint16_t volume); //0~30
|
||||
mp3_set_EQ (); //0~5
|
||||
mp3_pause ();
|
||||
mp3_stop ();
|
||||
void mp3_get_state (); //send get state command
|
||||
void mp3_get_volume ();
|
||||
void mp3_get_u_sum ();
|
||||
void mp3_get_tf_sum ();
|
||||
void mp3_get_flash_sum ();
|
||||
void mp3_get_tf_current ();
|
||||
void mp3_get_u_current ();
|
||||
void mp3_get_flash_current ();
|
||||
void mp3_single_loop (boolean state); //set single loop
|
||||
void mp3_DAC (boolean state);
|
||||
void mp3_random_play ();
|
||||
*/
|
||||
Reference in New Issue
Block a user