Ajout FishPeper

OpenSky/board/tinyfish_test/README.md

@@ -0,0 +1,3 @@
+# vd5m target
+
+this runs on a vd5m board

OpenSky/board/tinyfish_test/config.h

@@ -0,0 +1,77 @@
+// pin layout ISP header
+#define ISP_DATA  P2_1
+#define ISP_CLOCK P2_2
+
+// pin layout servo connection
+#define SERVO_1 7 // P0_7 = BIND, pull down on startup to enter bind mode
+#define SERVO_2 6 // P0_6 = ADC1 = voltage sensor (max 3.3V on I/O ! -> voltage divider necessary!)
+#define SERVO_3 5 // P0_5 = ADC0 = current sensor (max 3.3V on I/O !)
+#define SERVO_4 4 // P0_4 = PPM or SBUS OUT
+#define SERVO_5 3 // P0_3 = debug UART
+
+#define PPM_OUT_PIN SERVO_4
+
+// note: change of adc ch require change in adc.c!
+#define ADC_PORT P0
+// make sure not to use SERVO_3
+#define ADC0 SERVO_2
+#define ADC1 SERVO_2
+
+// voltage divider on my board is 10 / 3.3 k, scale to 100 / 33 to avoid floating point calc
+#define ADC0_DIVIDER_A 100
+#define ADC0_DIVIDER_B  33
+
+#define BIND_PORT P0
+#define BIND_PIN  SERVO_1
+
+// leds
+#define LED_GREEN_PORT P2
+#define LED_GREEN_PIN  4
+#define LED_RED_PORT P2
+#define LED_RED_PIN  3
+
+// DEBUG
+#define DEBUG_UART USART0_P0
+
+// SBUS
+// enable SBUS output -> this will DISABLE ppm!
+#define SBUS_ENABLED
+#define SBUS_UART USART1_P0
+// Note: default/futaba is INVERTED=1! (use this for a cc3d etc)
+//       inverted     => idle = LOW
+//       non inverted => idle = high
+// #define SBUS_INVERTED
+
+// PPM (only used if sbus is disabled)
+// invert SBUS output (normal is non inverted)
+// #define PPM_INVERTED
+
+// hub telemetry input (soft serial)
+#define HUB_TELEMETRY_ON_SBUS_UART
+// #define HUB_TELEMETRY_INVERTED
+
+#ifndef HUB_TELEMETRY_ON_SBUS_UART
+  // if not shared with sbus, use any pin in softserial mode at 9600baud
+  #define HUB_TELEMETRY_PORT        P0
+  #define HUB_TELEMETRY_PIN         7
+#endif
+
+// bootloader config
+#define BOOTLOADER_LED_GREEN_PORT LED_GREEN_PORT
+#define BOOTLOADER_LED_GREEN_PIN  LED_GREEN_PIN
+#define BOOTLOADER_LED_RED_PORT   LED_RED_PORT
+#define BOOTLOADER_LED_RED_PIN    LED_RED_PIN
+// bootloader runs on UART1 P0
+#define BOOTLOADER_UART_NUM           1
+#define BOOTLOADER_UART_PORT          0
+#define BOOTLOADER_UART_INVERTED      0
+#define BOOTLOADER_UART_BAUDRATE      100000
+#define BOOTLOADER_UART_USE_PARITY    1
+#define BOOTLOADER_UART_USE_2STOPBITS 1
+// use ISP interface clock pin as bootloader enable pin
+// pull this low during startup to enter bootloader mode
+#define BOOTLOADER_ENABLE_PORT P2
+#define BOOTLOADER_ENABLE_PIN  2
+
+
+#define DEFAULT_FSCAL_VALUE -20

OpenSky/board/tinyfish_test/target.mk

@@ -0,0 +1,9 @@
+# configuration of this board
+# cc2510f16 has 16k flash -> 0x4000
+# cc2510f32 has 32k flash -> 0x8000
+FLASH_SIZE=0x4000
+
+# continue with normal cc251x build
+ARCH_DIR = arch/cc251x
+ARCH_MAKEFILE = $(ARCH_DIR)/cc251x.mk
+