Ajout FishPeper

OpenSky/board/afrx/README.md

@@ -0,0 +1,3 @@
+# AFRX target
+
+AlienFlight CC2510 based receiver

OpenSky/board/afrx/config.h

@@ -0,0 +1,104 @@
+// pin layout ISP header
+#define ISP_DATA                    P2_1
+#define ISP_CLOCK                   P2_2
+
+// note: change of adc ch require change in adc.c!
+#define ADC_PORT                    P0
+#define ADC0                        6
+#define ADC1                        7
+// acs712 in inverted mode on adc1?
+// when powered by 5V we can use a trick
+// to get a good resolution: use inverted power inputs
+// 0A = 2.5V
+// 30A = 0.0V
+#define ADC1_USE_ACS712
+
+// voltage divider on my board is 10 / 1 k, scale to 100 / 10
+#define ADC0_DIVIDER_A              100
+#define ADC0_DIVIDER_B              10
+
+#define BIND_PORT                   P1
+#define BIND_PIN                    1
+
+// LEDs
+#define LED_GREEN_PORT              P2
+#define LED_GREEN_PIN               4
+#define LED_RED_PORT                P2
+#define LED_RED_PIN                 3
+
+// DEBUG
+#define DEBUG_UART 					USART0_P0
+
+// SBUS
+// enable SBUS output -> this will DISABLE ppm!
+#define SBUS_ENABLED
+#define SBUS_UART                   USART1_P0
+// Note: default/futaba is INVERTED=1! (use this for a cc3d etc)
+//       inverted     => idle = LOW
+//       non inverted => idle = high
+// #define SBUS_INVERTED
+
+// PPM (only used if sbus is disabled)
+// invert SBUS output (normal is non inverted)
+// #define PPM_INVERTED
+
+// hub telemetry input (soft serial)
+#define HUB_TELEMETRY_ON_SBUS_UART
+// #define HUB_TELEMETRY_INVERTED
+
+#ifndef HUB_TELEMETRY_ON_SBUS_UART
+  // if not shared with sbus, use any pin in softserial mode at 9600baud
+  #define HUB_TELEMETRY_PORT        P0
+  #define HUB_TELEMETRY_PIN         5
+#endif
+
+// LNA control pin
+#define RF_LNA_PORT                 P1
+#define RF_LNA_PIN                  6
+#define RF_LNA_ON_LEVEL             1
+
+// PA control pin
+#define RF_PA_PORT                  P1
+#define RF_PA_PIN                   4
+#define RF_PA_ON_LEVEL              1
+
+// Antenna switch control pin
+#define RF_ANTENNA_SWITCH_PORT      P1
+#define RF_ANTENNA_SWITCH_PIN       5
+#define RF_ANTENNA_A_LEVEL          1
+
+// enable High Gain?
+#define RF_HIGH_GAIN_MODE_ENABLED
+// Gain control pin
+#define RF_HIGH_GAIN_MODE_PORT      P1
+#define RF_HIGH_GAIN_MODE_PIN       7
+#define RF_HIGH_GAIN_MODE_ON_LEVEL  1
+
+// enable Bypass?
+// #define RF_BYPASS_MODE_ENABLED
+// Bypass control pin
+#define RF_BYPASS_MODE_PORT         P1
+#define RF_BYPASS_MODE_PIN          3
+#define RF_BYPASS_MODE_ON_LEVEL     1
+
+// bootloader config
+#define BOOTLOADER_LED_GREEN_PORT   LED_GREEN_PORT
+#define BOOTLOADER_LED_GREEN_PIN    LED_GREEN_PIN
+#define BOOTLOADER_LED_RED_PORT     LED_RED_PORT
+#define BOOTLOADER_LED_RED_PIN      LED_RED_PIN
+
+// bootloader runs on UART1 P0
+#define BOOTLOADER_UART_NUM         1
+#define BOOTLOADER_UART_PORT        0
+#define BOOTLOADER_UART_INVERTED    0
+#define BOOTLOADER_UART_BAUDRATE    100000
+#define BOOTLOADER_UART_USE_PARITY  0
+#define BOOTLOADER_UART_USE_2STOPBITS 0
+
+// use ISP interface clock pin as bootloader enable pin
+// pull this low during startup to enter bootloader mode
+#define BOOTLOADER_ENABLE_PORT      P2
+#define BOOTLOADER_ENABLE_PIN       2
+
+
+#define DEFAULT_FSCAL_VALUE         -69

OpenSky/board/afrx/target.mk

@@ -0,0 +1,8 @@
+# configuration of this board
+# cc2510f16 has 16k flash -> 0x4000
+# cc2510f32 has 32k flash -> 0x8000
+FLASH_SIZE=0x8000
+
+# continue with normal cc251x build
+ARCH_DIR = arch/cc251x
+ARCH_MAKEFILE = $(ARCH_DIR)/cc251x.mk