Serge NOEL
139 lines
4.8 KiB
Plaintext
139 lines
4.8 KiB
Plaintext
<!DOCTYPE html>
|
|
<html lang="en">
|
|
<head>
|
|
<meta name="generator" content="HTML Tidy for HTML5 for Apple macOS version 5.8.0">
|
|
<title>JMRI Hardware Support - Digikeijs / YAMORC</title>
|
|
<!--#include virtual="/help/en/parts/Style.shtml" -->
|
|
</head>
|
|
<body>
|
|
<!--#include virtual="/help/en/parts/Header.shtml" -->
|
|
|
|
<div id="mBody">
|
|
<!--#include virtual="../SidebarUp.shtml" -->
|
|
|
|
<div id="mainContent">
|
|
<h1>Hardware Support: Digikeijs / YAMORC</h1>
|
|
|
|
<h2 id="hardware">Supported Hardware</h2>
|
|
|
|
<h3>Command Station</h3>
|
|
|
|
<p>JMRI can connect to a Digikeijs DR5000 Digicentral command station, or the
|
|
new YAMORC command stations via a network connection or USB connection.</p>
|
|
|
|
<h2 id="limitations">Limitations</h2>
|
|
|
|
<p>Please report your results.</p>
|
|
|
|
<h2 id="connecting">Connecting</h2>
|
|
|
|
<h3>Settings</h3>
|
|
|
|
<p>To configure the connection:</p>
|
|
|
|
<h4>ESU/EcoS via network</h4>
|
|
|
|
<ul>
|
|
<li>Open the JMRI "Preferences" under the "Edit" menu (or the PanelPro menu on OS X)</li>
|
|
|
|
<li>Select "ESU" as the System Manufacturer</li>
|
|
|
|
<li>Select "ECoS via network" as the System Connection</li>
|
|
|
|
<li>Enter the IP address for your DR5000 unit</li>
|
|
|
|
<li>You may optionally change the connection name to "Digikeijs"</li>
|
|
|
|
<li>Leave the port number at 15471</li>
|
|
|
|
<li>Click "Save" & restart</li>
|
|
</ul>
|
|
|
|
<h4>Digitrax/LocoNet</h4>
|
|
|
|
<p>Providing that the Digikeijs DR5000 unit has been configured to use "LocoNet over TCP/IP
|
|
LBServer" protocol (Firmware version 1.3.0 when writing this documentation)</p>
|
|
|
|
<ul>
|
|
<li>Open the JMRI "Preferences" under the "Edit" menu (or the PanelPro menu on OS X)</li>
|
|
|
|
<li>Select Digitrax as the System Manufacturer</li>
|
|
|
|
<li>Select "LocoNet over TCP" as the System Connection</li>
|
|
|
|
<li>Enter the IP address for your DR5000 unit</li>
|
|
|
|
<li>Select whatever as Command station type (DCS210 Evolution Command Station)</li>
|
|
|
|
<li>Under Additional Connection settings, set port to 5550 if you use an original Digikeijs DR5000.
|
|
Set port to 1234 if you use a YaMoRC Command Station
|
|
or a Digikeijs DR5000 with YaMoRC Upgrade 9401.</li>
|
|
</ul>
|
|
|
|
<h4>Via USB</h4>
|
|
First, make sure your computer has the <a href=
|
|
"https://ftdichip.com/drivers/vcp-drivers/">correct USB drivers installed</a>.
|
|
<p>Then, set the JMRI connection preferences to:</p>
|
|
|
|
<ul>
|
|
<li>System Manufacturer: Digitrax</li>
|
|
|
|
<li>System connection: LocoNet LocoBuffer-USB</li>
|
|
|
|
<li>Serial Port: (as needed for your USB connection)</li>
|
|
|
|
<li>Command station type DSC100 (Chief)</li>
|
|
</ul>
|
|
|
|
<p>Turnout, Sensor, Signal and Throttle support is available for a JMRI-connected DR5000
|
|
unit.</p>
|
|
|
|
<h3>Throttles</h3>
|
|
|
|
<h3>Sensors</h3>
|
|
|
|
<p class="important">The S88 bus on the DR5000 (whether in use or not) is configured by default to think it has
|
|
one 16-channel input device connected. The S88 and LocoNet busses apparently share addresses.
|
|
Whenever an input from LS0 to LS15 goes HIGH on LocoNet, the S88 bus says 'NOPE'. The
|
|
resulting LOW signal is in turn broadcast onto the LocoNet bus. Set the number of connected
|
|
S88 units to zero in the (Windows) configuration application. (thanks to Steve R. Jan.
|
|
2018)</p>
|
|
|
|
<p>The Digikeijs DR4088LN and DR50018RC decoders can report occupancy state via LocoNet.<br>
|
|
The DR5088RC handles RailCom and is configurable via LNCV programming.</p>
|
|
|
|
<h3>Turnouts</h3>
|
|
|
|
<p>The Digikeijs DR4018 decoder can drive turnouts with several protocols.<br>
|
|
The DR4024 can drive 4 servos.<br>
|
|
Both are configurable in DecoderPro as a roster entry at address 9999.</p>
|
|
|
|
<h3 id="dr4018">Signals</h3>
|
|
|
|
<p>The Digikeijs DR4018 decoder can be configured for signaling using DecoderPro.<br>
|
|
To configure the signal Masts, use the <a href=
|
|
"../../../package/jmri/jmrit/beantable/SignalMastAddEdit.shtml#matrixCtl">Matrix Signal
|
|
Mast</a> driver.<br>
|
|
The Add Mast settings are:<br>
|
|
<a href="matrixPanelProrailCreate.png"><img src="matrixPanelProrailCreate.png" width="381"
|
|
height="489" alt="DCC Decoder panel"></a></p>
|
|
|
|
<h2 id="tools">Third Party info</h2>
|
|
|
|
<p>For more information on how to connect and use YAMORC products, refer to the following.
|
|
The old DR5000 works in a similar way.</p>
|
|
|
|
<ul>
|
|
<li>
|
|
<a href="http://yamorc.de/products/">YAMORC product documentation</a>
|
|
</li>
|
|
</ul>
|
|
<!--#include virtual="/help/en/parts/Footer.shtml" -->
|
|
</div>
|
|
<!-- closes #mainContent-->
|
|
</div>
|
|
<!-- closes #mBody-->
|
|
<script src="/js/help.js"></script>
|
|
</body>
|
|
</html>
|