Files
4f4acedbdd pm5: reduce idle power (core clock scaling + WFI idle)
Port the "reduce idle power" feature from the Fantasi firmware
(soeinova/Fantasi @ 9671309, plus its later ACC-SOF fix) to the PM5
(AT32F435) target.

Problem
-------
The PM5 firmware ran the ARM core at 288 MHz with a 1.3 V LDO and a
main loop that busy-polled at full speed even when the device was idle.
The 288 MHz PLL and the 1.3 V LDO dominate idle draw, and the busy loop
adds to it. Nothing scaled back when there was no work.

Change
------
New armsrc/pm5_power.c drives a refcounted clock/voltage governor:
- Idle (nothing pending, boost count 0, boot grace elapsed, FPGA off):
  take SCLK off the PLL onto HICK-48, power the PLL down, drop the LDO
  to 1.1 V, park the FPGA 24 MHz clock (PA8 low), and halt the core in
  WFI until the next IRQ or the 1 ms SysTick wake.
- Any timing-critical work holds a 288 MHz boost: AppMain wraps
  PacketReceived (which on the PM5 also covers a standalone mode, since
  it is only entered through a command there); the BWM low-batt poll
  and the RGB indicator wrap their I2C. Boost is refcounted and
  IRQ-guarded.
- USB (OS image) moves to the crystal-less HICK-48 clock, ACC-trimmed
  against the SOF, so powering the PLL down never touches USB. The
  bootrom keeps the HEXT/PLL USB path (AS_BOOTROM), so DFU flashing is
  unchanged.
- bwm_uart_clock_update() re-inits UART4 through the SDK usart_init()
  on each clock switch (the divider set at 288 MHz is 6x off at 48 MHz).
- FpgaIsOff() (fpga_core.c, PM5 only) tracks the last conf word so the
  governor never downclocks while a reader field / emulation is running.
- Wake preamble on the BWM link: the companion module firmware
  (Proxmark5_BWM_esp32) light-sleeps 2 s after the last byte on the link
  and its UART wakes on RX edges but loses the bytes that carried them.
  bwm_uart_write() therefore leads with four 0x55 bytes and a 10 ms
  settle on its first write and after 1 s without a write of its own
  (RX is not tracked: the ring can be drained long after the bytes
  came in). The module only starts light-sleeping once it has seen a
  preamble, so the one sent while it was still booting is repeated
  after the boot-time link negotiation. A module firmware without light
  sleep drops the preamble as noise.

New `hw powersave on|off` toggles the governor at runtime (default on);
`hw status` reports the idle-clock and WFI-asleep fractions.

Behaviour change
----------------
- PM5 idles at 48 MHz with the PLL off and the CPU halted; it boosts to
  288 MHz for commands and BWM housekeeping. Command timing and
  throughput are unchanged (intra-command work is always boosted).
- PM5 USB now runs off HICK-48 (ACC-trimmed) instead of the HEXT PLL.
- New command id CMD_PM5_POWERSAVE (0x0180).

Testing
-------
Built warning-free (gcc) for PLATFORM=PM5 (with and without
PLATFORM_EXTRAS=BWM), PM3RDV4 and PM3GENERIC, armsrc and bootrom. Client
built via the default Makefile. Not built with clang or on
Windows/macOS; nothing outside PM5/AT32 guards changes.

Flashed to a PM5 and exercised against a MIFARE Classic 4K card:
hw version/status/ping (4000 & 512 B), hw tune, hf search, hf 14a
info/reader (x12 across idle gaps), hf mf info/chk/rdbl, lf search/read,
hw powersave off/on, held-field (raw -sk) correctly blocks the downclock,
hw reset + re-enumerate. All pass; USB stays up across downclocks. Idle
reaches ~80-95% at 48 MHz and ~90%+ WFI-halted after a few seconds idle.
Measured at the USB port: idle draw 283 mA -> 207 mA with the stock
BWM firmware.

Co-authored-by: Soei Nova <soeinova@proton.me>
Co-authored-by: noproto <noproto@zeroday.engineering>
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
2026-09-24 10:33:46 +02:00

47 lines
1.6 KiB
C

//-----------------------------------------------------------------------------
// Copyright (C) Proxmark3 contributors. See AUTHORS.md for details.
//
// This program is free software: you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation, either version 3 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// See LICENSE.txt for the text of the license.
//-----------------------------------------------------------------------------
// Proxmark5 power-save idle: core clock scaling + WFI - see pm5_power.c.
//-----------------------------------------------------------------------------
#ifndef PM5_POWER_H__
#define PM5_POWER_H__
#include "common.h"
#ifdef PM5
// Call once from AppMain after USB is up.
void pm5_power_init(void);
// Refcounted hold on the full 288 MHz core clock. Wrap anything with timing
// that assumes the boot clock (commands, standalone mode, I2C, buzzer).
void pm5_power_boost(void);
void pm5_power_unboost(void);
// Main-loop idle step: drop to the idle clock when allowed, then halt the core
// until the next IRQ or the 1 ms wake tick.
void pm5_power_idle(void);
// Runtime toggle (default on). Off = stay at 288 MHz and spin.
void pm5_power_set_enabled(bool on);
bool pm5_power_get_enabled(void);
// `hw status` section.
void pm5_power_print_status(void);
#endif // PM5
#endif // PM5_POWER_H__