Without options the UID and the Philips MFG string are now read from the
tag, `-r` is gone. `--uid` is the offline path, and the new `--mfg` gives
the Philips toothbrush algo its MFG string offline, which used to need
the tag on the antenna. Help shows a working Philips sample taken from
the generator self test vector, also run by pm3_tests.sh.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Bring the SAM commands to parity with Seader's (bettse/seader, GPLv3)
read and save options:
- hf mf sam: MIFARE Classic SE via CMD_HF_SAM_MFC
- hf mfdes sam: DESFire EV1/EV2 via CMD_HF_SAM_SEOS, as Seader drives it
- --dg legacy|sr|prox|mfc and --save on hf iclass / seos / mf / mfdes sam
- wiegand downgrade: the same outputs offline, from a saved credential
or PACS bits, plus --selftest
Outputs follow seader_credential.c:
- legacy / sr: 20 block iCLASS dump, Seader's config, epurse, Kd from the
HID standard key, block 6 03030303 0003E014 (A3 for SR, PACS left
unencrypted), PACS in block 7, SR SIO in blocks 10-17. A CSN read from
iCLASS is kept, anything else gets Seader's fake CSN 7AF53113FEFF12E0.
- mfc: 1K dump with Seader's block 0, MAD, HID sector 1 keys and PACS in
block 5, the layout hf mf encodehid writes.
- prox: lf hid clone --bin, and -w H10301 for 26 bits as Seader does.
- --save: a "hid credential" JSON with PACS, bits, UID, SIO, media type.
The PACS parsing hf iclass sam and hf seos sam each had a copy of moves
to hidsio.c; hf seos sam is now the shared ISO14443-A command.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
New client command for VivoKey Thermo / Temptress style implants. The
NTAG 5 link (NTP5332) is used as I2C master: energy harvesting is enabled
through the EH_CONFIG_REG session register (AN12365), the TI sensor is
driven with WRITE I2C / READ I2C / READ SRAM and the I2C master status
register is polled for completion and NAKs. Sensors at 0x48-0x4B are
probed and identified by the TMP117/TMP119 device id register, a one-shot
conversion is triggered and the result printed in C and F.
Pure client side, uses CMD_HF_ISO15693_COMMAND with the field kept on.
Offline self test for the conversions is hooked into pm3_tests.sh, and
hf 15 info hints at the command for NTAG 5 tags.
Not tested on hardware, no implant available.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
New `hf goodisplay load` for the NFC-D1 tags GDEY0154D67, GDEY0213B74,
GDEY029T94 and GDEY037T03. They use a Fudan FM1280 talking ISO14443-4
with proprietary CLA F0 APDUs (config F0 DB/DA, image F0 D2 in 250 byte
chained blocks, refresh F0 D4), unlike the raw 14a CD xx frames of
Waveshare tags, hence a separate command family. Protocol and init
sequence from the Flipper Zero NFC Eink app (GPLv3, RebornedBrain).
Image load/crop/dither, save and 1bpp packing move from cmdhfwaveshare.c
into imgutils.c so both commands share them. Waveshare output is
unchanged.
hf 14a info hints at hf waveshare for its known UIDs (now incl. FSTN11m)
and at hf goodisplay for a SAK 28 ATS 0B 78 33 A0 02 90 <UID> 00 tag.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The page check covers the Hitag 2, S and µ `wrbl`, the data check S and
µ. `htu rdbl -c` stops at the 55 blocks the reply holds, `hts -m` above
3 is refused, `ta -h` shows its help and argument errors free the
parser.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Annotators, `trace extract`, `-x` and `-c` stay inside the frame, the
trace and the row buffer, `-t ht2` inside the Hitag 2 state, and frame
lengths are 16 bit wide. Topaz, FeliCa and five byte ISO14443-A frames
get the right CRC check, Topaz and iCLASS traces tell their ISO14443-A
and ISO15693 frames apart, and the SEOS, 14b, DESFire and Hitag µ
labels are corrected. Six make check expectations on the repository
traces cover the fixes.
Co-Authored-By: Claude Mythos 5.1 <noreply@anthropic.com>
demod splits the starting digit from the reserved bits, writes the
animal code as CCC NNNNNNNNNNNN, knows all 249 ISO 3166-1 countries
and shows Bio-Thermo only for the chips' exact trailer. clone and sim
refuse values the frame can't carry, sim sends the data block flag for
--extended 000000 and stops with Enter, reader also tries 125 kHz.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
lf destron sim only printed "To be implemented". It now sends the
frame that lf destron clone writes, FSK2 RF/50 as in the clone's T5577
config. Both take 5 bytes of 00-7F: clone wrote a byte above 7F
without its top bit and padded a short uid with FF of bad parity.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
clone took negative FC and CN, and MS values above 5 and 22 bits,
without a word: MS FC 40 wrote the card of FC 8. sim let ids of 32
bits or more change the fixed bits, so --id 2147483648 simulated id 0,
and printed the shifted frame as Internal Id. The sim help example
used --cn, the option is --id, and the clone hint named lf keri read.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
HPP32 wrote its card number 10 bits past the 32-bit frame, it now uses
bits 13-30 as cardinfo shows. H10320 wrote its first digit over the
leading one, so decode refused most numbers, and two of its parity
masks had typos. S12906b needed ParityValid, which no caller sets.
HGen37 decode checked bit 28 instead of 26. The limits of nine formats
did not match the fields Pack writes. wiegand list printed the usage
of wiegand info.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A NULL TLV has no length, so a run of them swallowed the TLVs after
it. Lock and Memory Control sizes of 0 mean 256, the nibbles of their
third byte are powers of two and the Memory Control size counts bytes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The values went through uint8_t or & 0xFF, so --max 300 ran with 44
and --samples 1000 with 232. The --fs clocks stay 8-bit in the FSK
demod and are now refused above 255.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
mfulc_des_brute added the Homebrew openssl@3.6 include directory, which
the macOS runners no longer have, and -Wmissing-include-dirs under
-Werror stopped the build. It now uses brew --prefix openssl, as #3734
did for mfd_aes_brute.
Since MSYS2 filesystem 2026.10.18 /etc/profile runs post-install
scripts on the first start only, so ProxSpace never installed its
packages and the build found no arm-none-eabi-gcc. The workflow now
runs ProxSpace's setup script when setup\installed is missing.
The third mfulc_des_brute test in pm3_tests.sh is now labelled 3/3.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Read SBS before TIME/DATE to latch a coherent snapshot in synchronous
ERTC mode. A rollover between the previous calendar and subsecond reads
could move the tick count backwards and cause false receive timeouts.
Preserve millisecond conversion and shared delta-helper semantics.
Add actual-source rollover, conversion and register-locking coverage.
Leave acquisition limits and RF timing unchanged.
Co-Authored-By: OpenAI coding assistant <noreply@openai.com>
Signed-off-by: nip <182409448+nip-was-here@users.noreply.github.com>
At fc/2 the subcarrier is a one-sample alternation and pskRawDemod_ext finds
wave tops one sample at a time, unfiltered. On a weak tag, sample noise erases
tops; a wave then reads as four samples and counts as a phase shift, and the
bit stream fills with errors although every bit is still in the trace. A T5577
Indala at 22 mm gave the wrong card on 14 of 50 lf search reads.
PSKDemod keeps the tracker's result whenever it is clean, so nothing changes
where master already works. Otherwise, for fc/2, it tries the existing coherent
receiver pm3_psk_demod (now with an optional per-symbol magnitude output) and
keeps that only if it scores well above what level-step leakage can produce,
its bits aren't doubled or constant, and no symbol is weak. The receiver's
output is differential, so one bad decision would flip every later bit: a weak
symbol refuses the trace rather than risk a wrong card (absolute decisions with
weak symbols left to maxErr were tried and gave wrong IDs on dropouts). With no
usable clock from the caller, candidate clocks are tried largest first. Polarity is voted from the
raw level over each phase reversal, the cue pskFindFirstPhaseShift reads at the
first one. Client only; firmware is unchanged.
Base vs this change, same captures:
- T5577 Indala, live lf search: 22 mm 3 right / 14 wrong -> 50 / 0; 24 mm
0 / 2 -> 50 / 0; 26 mm and 0-20 mm unchanged
- lf t55xx dump, live: 22 and 24 mm blocks 0-2 and page 1 correct 5/5 where
master reads nothing; unchanged where master reads
- emulated Indala (Chameleon Ultra, clock drifting against the reader):
lf search right / wrong 56 / 130 -> 91 / 95 of 200; every one of the 95 is
master's own wrong ID on the same capture
- 27 PSK traces in traces/, weakened with Gaussian noise: correct 341 -> 636 of
810, wrong IDs 83 -> 21; with recorded Proxmark noise 367 -> 553 of 648,
33 -> 27. No lost reads and no new wrong IDs in either
- traces/lf_*.pm3 (99): lf search -1 and -1 -c output identical; 1,581
non-PSK probes: lf search and lf t55xx detect identical
- 200 empty-field captures: no decode, either build
tools/pm3_tests.sh: a weak 24 mm Indala trace must read its ID (fails on
master), and a synthetic NRZ with an fc/2 ripple must not decode as a tag
(the level-step leakage the score check rejects).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Add bidirectional conversion between DFC v4 credentials and mfdes v1 JSON, with documentation and round-trip coverage. Include H10301 FC69 CN420 factory and field fixtures and an external HID reader test target.
Co-Authored-By: GPT-Daybreak Blue <noreply@openai.com>
Three ways this command reported a credential that was not on the tag.
CmdIdteckDemod always passed its local raw[8] to demodIdteck, never NULL, so
without --raw the command decoded a zeroed stack array rather than the
graphbuffer and reported card id 0 every time. The help's own first example,
plain `lf idteck demod`, has been doing that since --raw was added. It now
passes NULL when no --raw is given, which is the signal path demodIdteck
already has and lf idteck reader already uses.
A raw frame whose first word is not 4944544B printed "No genuine IDTECK found"
and then fell through and announced a tag anyway, with a card id read out of
whatever was passed in. It now stops there. The signal path cannot reach this:
detectIdteck matches the full 32 bit preamble, so lf search and lf idteck
reader are unaffected.
Finally the Idteck card id was packed into a 26 bit wiegand_message_t and run
through HIDUnpack, which prints an HID H10301 line with a facility code and
card number. That is not a decode of anything - the id is 24 bits, byte
reversed off the wire, and Unpack_H10301 returns true for any 26 bit message,
so the parity flag is the only hint and it reads ok for 25% of card ids by
chance. Both committed Idteck traces show it: 4944544B351FBE4B prints
FC: 37 CN: 57103 parity ( ok ), AC40E069 prints FC: 52 CN: 61472 parity
( fail ). Dropped, with the wiegand_formats.h include that came in with it.
Added five offline regression tests. Three fail without this change, one per
defect; lf search over every committed lf trace is byte identical before and
after apart from the two removed H10301 lines.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
restore_bufferS32() returns the length it put back and every graph-buffer
caller dropped it, so g_GraphTraceLen kept whatever value the code between
save and restore had left.
In try_detect_modulation() that is the 160 sample psk antenna-settle trim:
`data modulation` gave the buffer's samples back but left it 160 short, and
a following demod lost round(160 / clk) bits off the end. check_chiptype()
loses the same way through the acquisitions its detections make, on the
`lf search` path, and for g_DemodBuffer too. demodTI() loses convLen + 16
on its error path.
save_graphbuffer() / restore_graphbuffer() pair the length and grid offset
with the contents so no call site has to remember them. The visa2000 and
zx8211 sites do not change the length, so converting them is a no-op today
and keeps the next one from being a bug.
Regression test in tools/pm3_tests.sh: `data modulation` on a saved psk1
trace must leave all 20000 samples.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Adds support for more attribute types and safe
error handling for unknown types. Fixes a bug
where the version attribute didn't increment the
cursor correctly causing an infinite loop.
e2cf7dee5 removed sim014.bin but the top-level Makefile still lists it
in INSTALLSIMFW, so 'make install' fails on cp. Install sim020 instead,
and point the pm3_tests.sh existence check at the same file.
Extract the reusable Wiegand normalization and packing flow into
wiegand_formatutils and move existing callers onto that shared path.
This rebuilds the feat-wiegand branch as one focused commit against
upstream/master instead of trying to preserve the original commit chain.
Key changes:
- add shared helpers for plain binary, raw HID, new PACS, and formatted
Wiegand input
- centralize binary rendering used by cmdwiegand and PACS decode output
- update lf hid sim/clone to resolve one input mode through the shared
Wiegand layer and enforce the LF packed transport limit explicitly
- update hf mf encodehid to accept bin/raw/new/formatted Wiegand input
through the same normalization path
- preserve legacy raw HID transport behavior while clarifying the
packed-HID vs LF transport limits in error reporting
- add offline regression coverage for the new PACS decode output and add
interactive online targets for LF HID Wiegand and MIFARE encodehid
Validation performed:
- make client
- bash -n tools/pm3_tests.sh
- bash -n tools/pm3_online_tests.sh
- ./tools/pm3_online_tests.sh -h
- ./client/proxmark3 -c 'wiegand encode -w H10301 --fc 31 --cn 337'
- ./client/proxmark3 -c 'wiegand encode -w H10301 --fc 31 --cn 337 --new'
- ./client/proxmark3 -c 'wiegand decode --new 068F80A8C0'