297 Commits
Author SHA1 Message Date
WillandCursor 8150c2af77 BWM: add ability to flash over wifi
Co-authored-by: Cursor <cursoragent@cursor.com>
2026-09-26 12:23:47 -04:00
Iceman cbadbf4bfe Merge branch 'master' into pm5-idle-lowpower
Signed-off-by: Iceman <iceman@iuse.se>
2026-09-26 21:51:29 +07:00
Tom HarknessandClaude Sonnet 5 2b5e3e51eb Add PM5 CEP transport for Flipper Zero (WITH_CEP)
Wire up the previously-dead Flipper Zero handshake/SPI code from
at32_unit_test.c into a real WITH_CEP platform extra, independent of
BWM (new g_reply_via_cep flag, not reusing BWM's g_reply_via_fpc, so
both transports can run concurrently).

Fixes a real reconnect bug found during hardware bring-up: the
handshake listener was gated on a CC-controller attach edge that
didn't reliably fire on every FAP relaunch, requiring a physical
cable replug to reconnect. Now watches for a fresh incoming byte any
time the link reports attached, with a bounded receive timeout so a
stray byte can never hang the main loop.

RF/FPGA-dependent functionality (hf/lf reads) is out of scope here -
tracked separately. Closes #3667.

Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
2026-09-26 09:45:51 -04:00
4f4acedbdd pm5: reduce idle power (core clock scaling + WFI idle)
Port the "reduce idle power" feature from the Fantasi firmware
(soeinova/Fantasi @ 9671309, plus its later ACC-SOF fix) to the PM5
(AT32F435) target.

Problem
-------
The PM5 firmware ran the ARM core at 288 MHz with a 1.3 V LDO and a
main loop that busy-polled at full speed even when the device was idle.
The 288 MHz PLL and the 1.3 V LDO dominate idle draw, and the busy loop
adds to it. Nothing scaled back when there was no work.

Change
------
New armsrc/pm5_power.c drives a refcounted clock/voltage governor:
- Idle (nothing pending, boost count 0, boot grace elapsed, FPGA off):
  take SCLK off the PLL onto HICK-48, power the PLL down, drop the LDO
  to 1.1 V, park the FPGA 24 MHz clock (PA8 low), and halt the core in
  WFI until the next IRQ or the 1 ms SysTick wake.
- Any timing-critical work holds a 288 MHz boost: AppMain wraps
  PacketReceived (which on the PM5 also covers a standalone mode, since
  it is only entered through a command there); the BWM low-batt poll
  and the RGB indicator wrap their I2C. Boost is refcounted and
  IRQ-guarded.
- USB (OS image) moves to the crystal-less HICK-48 clock, ACC-trimmed
  against the SOF, so powering the PLL down never touches USB. The
  bootrom keeps the HEXT/PLL USB path (AS_BOOTROM), so DFU flashing is
  unchanged.
- bwm_uart_clock_update() re-inits UART4 through the SDK usart_init()
  on each clock switch (the divider set at 288 MHz is 6x off at 48 MHz).
- FpgaIsOff() (fpga_core.c, PM5 only) tracks the last conf word so the
  governor never downclocks while a reader field / emulation is running.
- Wake preamble on the BWM link: the companion module firmware
  (Proxmark5_BWM_esp32) light-sleeps 2 s after the last byte on the link
  and its UART wakes on RX edges but loses the bytes that carried them.
  bwm_uart_write() therefore leads with four 0x55 bytes and a 10 ms
  settle on its first write and after 1 s without a write of its own
  (RX is not tracked: the ring can be drained long after the bytes
  came in). The module only starts light-sleeping once it has seen a
  preamble, so the one sent while it was still booting is repeated
  after the boot-time link negotiation. A module firmware without light
  sleep drops the preamble as noise.

New `hw powersave on|off` toggles the governor at runtime (default on);
`hw status` reports the idle-clock and WFI-asleep fractions.

Behaviour change
----------------
- PM5 idles at 48 MHz with the PLL off and the CPU halted; it boosts to
  288 MHz for commands and BWM housekeeping. Command timing and
  throughput are unchanged (intra-command work is always boosted).
- PM5 USB now runs off HICK-48 (ACC-trimmed) instead of the HEXT PLL.
- New command id CMD_PM5_POWERSAVE (0x0180).

Testing
-------
Built warning-free (gcc) for PLATFORM=PM5 (with and without
PLATFORM_EXTRAS=BWM), PM3RDV4 and PM3GENERIC, armsrc and bootrom. Client
built via the default Makefile. Not built with clang or on
Windows/macOS; nothing outside PM5/AT32 guards changes.

Flashed to a PM5 and exercised against a MIFARE Classic 4K card:
hw version/status/ping (4000 & 512 B), hw tune, hf search, hf 14a
info/reader (x12 across idle gaps), hf mf info/chk/rdbl, lf search/read,
hw powersave off/on, held-field (raw -sk) correctly blocks the downclock,
hw reset + re-enumerate. All pass; USB stays up across downclocks. Idle
reaches ~80-95% at 48 MHz and ~90%+ WFI-halted after a few seconds idle.
Measured at the USB port: idle draw 283 mA -> 207 mA with the stock
BWM firmware.

Co-authored-by: Soei Nova <soeinova@proton.me>
Co-authored-by: noproto <noproto@zeroday.engineering>
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
2026-09-24 10:33:46 +02:00
Philippe Teuwen e2acee8a85 Revert "Release v4.23346 - Frosty Lemon"
This reverts commit dc0110c29d.
2026-09-18 00:22:18 +02:00
Philippe Teuwen dc0110c29d Release v4.23346 - Frosty Lemon 2026-09-18 00:22:18 +02:00
iceman1001 199c3f107c fix image too large for 256kb devices by adding guards 2026-09-16 10:32:48 +02:00
iceman1001 a7b1276781 phase 1 simulation and desfire fixes... 2026-09-14 21:13:10 +02:00
iceman1001andClaude Opus 5 (1M context) 43fe6c3eb8 fpga_compress: pick the LZ4 block size by consumer, not by file count
The 1 MB block branch exists for the ARM .data section: start.c's
uncompress_data_section() reads one 4-byte length and does one
LZ4_decompress_safe(), so .data has to arrive as a single block. It was
selected by 'num_infiles == 1', which is not what tells the two callers apart.

A build that skips LF, FeliCa and ISO15693 leaves FPGA_BITSTREAMS holding just
fpga_pm3_hf.bit, so the bitstream took that same branch and was packed as one
42 kB block. get_from_fpga_combined_stream() decompresses into a
FPGA_RING_BUFFER_BYTES buffer, 16 kB since 83c3f81b1:

  [#] inflate returned: -13247
  [#] reset_fpga_stream failed

Before 83c3f81b1 the copy was clamped with MIN(FPGA_RING_BUFFER_BYTES, ...)
whatever buffer_size said, so the blocks came out at 30 kB and the 30 kB ring
buffer still took them. That is why the commit looks like the cause - it only
removed the clamp that was covering for the wrong branch.

Add -s for the single block case and let the FPGA path always chop at
FPGA_RING_BUFFER_BYTES, however many bitstreams went in:

  4 bitstreams   169344 in -> 106933 out, byte identical to before
  1 bitstream     42172 in ->  28718 out, 3 blocks 13265/13206/2247,
                                          was 1 block of 27627
  .data  (-s)     14944 in ->   8786 out, byte identical to the
                                          obj/fullimage.data.bin.z in tree

Also hand the ring buffer back when reset_fpga_stream() fails. The early
return left it allocated for the rest of the session, which is the reporter's

  [#]   BigBuf_size............. 48116
  [#]   Available memory........ 31732

48116 - 31732 is 16384, exactly FPGA_RING_BUFFER_BYTES.

No CAPABILITIES_VERSION bump: fpga_all.bit.z is objcopy'd into the same
fullimage as the decompressor that reads it, so nothing here is client facing.

Reported and correctly diagnosed by @ewangsoft.

Fixes #3599

Co-Authored-By: Claude Opus 5 (1M context)
2026-09-13 08:14:43 +02:00
iceman1001 2fc7f81a4a fix PM3_GENERIC builds. dont compile SAM-sim module things 2026-09-01 13:30:04 +02:00
iceman1001 96ed916074 recompress fpga streams 2026-09-01 11:34:45 +02:00
Niel Nielsen 4cf2e83c3a Add support for BWM charger, buzzer, and RGB indicator
Signed-off-by: Niel Nielsen <nieldk@gmail.com>
2026-08-28 13:10:24 +02:00
Niel Nielsen fcd03515b4 Add bwm_wifi.c to SRC_BWM when WITH_BWM_FORWARD is set
Signed-off-by: Niel Nielsen <nieldk@gmail.com>
2026-08-27 13:13:29 +02:00
Niel Nielsen fc2fcc890c Add files via upload
Signed-off-by: Niel Nielsen <nieldk@gmail.com>
2026-08-26 16:07:37 +02:00
Nemanja Nedeljkovic 6507b8f36b feat(pm5): hf tune --rgb / lf tune --rgb - antenna RGB as a tuning meter
Adds an opt-in `--rgb` flag to the continuous `hf tune` / `lf tune` commands that
mirrors the antenna tuning level on the PM5 antenna RGB LED: blue = low, green =
mid, red = high, tracking the on-screen bar so you can find coupling (e.g. an
implant) by feel without watching the screen.

The colour is computed client-side from the same per-iteration voltage / running
peak the bar uses (so it matches the bar and auto-scales), and pushed to the
device via a new dumb CMD_PM5_RGB_SET {r,g,b}. That command is handled (#ifdef
PM5) by a dedicated AT32 RGB HAL module, common_arm/rgb/{rgb_apis.h,
rgb_hw_at32.c} (RgbLedSet(), I2C controller @ 0x48), wired into the armsrc
Makefile/CMake as SRC_RGB for PM5 only - so no other platform is affected and no
hardware code lands in shared files.
2026-08-20 11:55:55 +02:00
dxl d286946d0f Update the Makefile support for ARM 2026-08-19 15:51:53 +02:00
kormax 4ad136b5db Implement 'hf felica sim' command 2026-06-12 18:31:57 +03:00
Philippe Teuwen d8c7f84598 Add Makefile PLATFORM_FILE variable to specify another Makefile.platform file 2026-05-19 00:10:17 +02:00
Antiklesys abe54994d2 Implemented SC operations 2026-05-11 13:54:49 +08:00
Philippe Teuwen e7de85a1a3 ARM LZ4: prevent compilation of functions using malloc/free
They were discarded by the linker GC as they weren't used so far, but better be safe...
2026-04-28 13:00:43 +02:00
Philippe Teuwen 6efff9a6ae ARM: tidy compilation flags 2026-04-28 13:00:42 +02:00
Philippe Teuwen 294b656af1 Fix ARM compilation on Debian Forky & the new picolibc replacing newlib.
Debian Forky's gcc-arm-none-eabi uses picolibc as the default C library, replacing the old newlib-nano.
Picolibc registers itself with GCC via a .specs file.
That specs file automatically injects its own picolibc.ld into every link step — unless GCC sees a user-supplied -T flag at the GCC driver level.
https://github.com/picolibc/picolibc/blob/main/doc/linking.md
2026-04-28 13:00:42 +02:00
Philippe Teuwen 961e59b5d1 Revert "Release v4.21611 - BREAKMEIFYOUCAN!"
This reverts commit aaacc75e9f.
2026-04-14 10:19:30 +02:00
Philippe Teuwen aaacc75e9f Release v4.21611 - BREAKMEIFYOUCAN! 2026-04-14 10:19:30 +02:00
Antiklesys 128e4006bf SE Conf Card Sim Base
Added `hf secc` to build a base for simulating basic function of iclass SE config cards
2026-03-30 22:58:52 +08:00
iceman1001 338ab9c81a Revert "Release v4.21128 - Permafrost"
This reverts commit b10235b03b.
2026-02-25 16:15:01 +01:00
iceman1001 b10235b03b Release v4.21128 - Permafrost 2026-02-25 16:15:01 +01:00
Aaron Tulino (Aaronjamt) c0e82539f2 [hf seos] Simulate support 2025-12-21 04:26:44 -07:00
Aaron Tulino (Aaronjamt) 63fc2b415d Add 3DES CMAC for ARM 2025-12-21 00:34:11 -07:00
iceman1001 3595f42f6d add secure messaging for UL_AES. Calculating CMAC on device side 2025-10-17 13:31:19 +02:00
iceman1001 628d8633f7 Revert "Release v4.20728 - Phrack"
This reverts commit ee9b3f4acb.
2025-09-11 20:31:08 +02:00
iceman1001 ee9b3f4acb Release v4.20728 - Phrack 2025-09-11 20:31:08 +02:00
iceman1001 1f718683b3 Revert "Release v4.20469 - Daddy Iceman"
This reverts commit 9fa173c727.
2025-06-16 16:18:01 +02:00
iceman1001 9fa173c727 Release v4.20469 - Daddy Iceman 2025-06-16 16:18:01 +02:00
iceman1001 6ed1853320 Revert "Release v4.20142 - Blue Ice"
This reverts commit a657dbda9b.
2025-03-25 16:18:49 +01:00
iceman1001 a657dbda9b Release v4.20142 - Blue Ice 2025-03-25 16:18:49 +01:00
douniwan5788 4bde83b89d Added lf hitag htu support for Hitag µ/8265 2025-03-19 18:56:23 +08:00
douniwan5788 3d0c8cab5c Refactor Hitag low-level functions into hitag_common 2025-03-19 17:05:39 +08:00
iceman1001 fc06cafc2f moving emvsim.c since it needs smartcard functions 2025-01-14 21:40:14 +01:00
Iceman 76ad5a5b51 Merge branch 'master' into cherry_pick_emv
Signed-off-by: Iceman <iceman@iuse.se>
2025-01-14 16:26:35 +01:00
Jakub Kramarz 661b7bad22 armsrc/sam_picopass.c: extract common routines to sam_common.c 2025-01-07 00:04:48 +01:00
iceman1001 daff8228a2 Revert "Release v4.19552 - Orca"
This reverts commit a039ac18cc.
2024-11-22 12:15:19 +01:00
iceman1001 a039ac18cc Release v4.19552 - Orca 2024-11-22 12:15:19 +01:00
n-hutton 4a23fb05f0 Cherry pick POC of emv simulation 2024-11-21 19:23:03 +00:00
iceman1001 b881bbbd00 Revert "Release v4.18994 - Backdoor"
This reverts commit cd6dc880ad.
2024-09-10 15:40:28 +02:00
iceman1001 cd6dc880ad Release v4.18994 - Backdoor 2024-09-10 15:40:28 +02:00
douniwan5788 80b9f6bb4d refactor: Renamed WITH_NO_COMPRESSION to WITH_COMPRESSION for consistent style 2024-09-04 22:48:55 +08:00
iceman1001 7329dcd3bf Revert "Release v4.18589 - Aurora"
This reverts commit aceed281e8.
2024-05-28 10:36:32 +02:00
iceman1001 aceed281e8 Release v4.18589 - Aurora 2024-05-28 10:36:32 +02:00
iceman1001 c8849af5e0 This is the major changes made to the HITAG2 commands. Its heavly based on RFIDLers implementation and its been converted to work with Proxmark3. Special thanks to @kevsecurity for his amazing implementations of the Gone in 360 Seconds paper by Roel, Flavio & Balasch. Thanks to @adamlaurie for his RFIDler project. It wouldnt been doable without it. 2024-04-22 16:20:24 +02:00