diff --git a/armsrc/appmain.c b/armsrc/appmain.c index 9b56c354c..47aa50497 100644 --- a/armsrc/appmain.c +++ b/armsrc/appmain.c @@ -142,6 +142,8 @@ static bool g_bwm_present = false; #define BWM_GAUGE_TEMP 0x02 // 0.1 K #define BWM_GAUGE_VOLTAGE 0x04 // mV #define BWM_GAUGE_REMCAP 0x0C // mAh +#define BWM_GAUGE_FCC 0x0E // mAh, FullChargeCapacity (health: FCC/design cap) +#define BWM_DEFAULT_DESIGN_CAP_MAH 500 // VXE 502540 fitted cell (500 mAh, 3.7 V) #define BWM_GAUGE_CURRENT 0x10 // signed mA #define BWM_GAUGE_SOC 0x1C // % @@ -156,6 +158,7 @@ static bool bwm_gauge_read16(uint8_t cmd, uint16_t *out) { // Reads the BWM charger + fuel gauge and prints a battery section. Called from // SendStatus() under #ifdef PM5, so it only runs on a booted PM5 with I2C available. +static bool bq_read_design_cap(uint16_t *cap); // fwd decl (defined with the provisioning code below) static void print_pm5_battery_status(void) { if (g_bwm_present == false) { return; // no BWM detected at boot; nothing to report @@ -243,6 +246,22 @@ static void print_pm5_battery_status(void) { (cur < -5) ? _YELLOW_("(discharging)") : "(idle)"); Dbprintf(" Remaining capacity.. %u mAh", rem); Dbprintf(" Temp (gauge)........ %d.%d C", tempC10 / 10, tabs % 10); + + // Battery health: FullChargeCapacity (0x0E) vs the gauge's programmed Design + // Capacity. FCC is the gauge's learned present full capacity; health = FCC/design. + // NOTE: only meaningful once the gauge has run an Impedance Track learning cycle + // (a full charge/discharge). Before that it is an unconverged estimate. If Design + // Capacity was never provisioned (hw bwmsetcap), the ratio is against the gauge + // default, not the fitted cell - so it can read wildly wrong. + uint16_t fcc = 0, design = 0; + if (bwm_gauge_read16(BWM_GAUGE_FCC, &fcc) && fcc > 0) { + if (bq_read_design_cap(&design) == false || design == 0) { + design = BWM_DEFAULT_DESIGN_CAP_MAH; // fall back to the fitted-cell rating + } + unsigned health = (unsigned)(((uint32_t)fcc * 100) / design); + Dbprintf(" Full charge cap..... %u mAh (design %u)", fcc, design); + Dbprintf(" Battery health...... %u %% " _YELLOW_("(needs a full cycle to be accurate)"), health); + } } else { Dbprintf(" Fuel gauge.......... " _YELLOW_("not responding") " (BQ27427 absent or I2C down)"); } @@ -255,7 +274,6 @@ static void print_pm5_battery_status(void) { // because a config-update cycle disrupts the Impedance Track learning cycle. // Per BQ27427 TRM (SLUUCD5): State subclass 82 (0x52), Design Capacity at offset 6 // -> block addr 0x46 (MSB)/0x47 (LSB), big-endian. Assumes gauge UNSEALED (factory default). -#define BWM_DEFAULT_DESIGN_CAP_MAH 500 // VXE 502540 on the reference BWM static bool bq_control(uint16_t sub) { uint8_t d[2] = { (uint8_t)(sub & 0xFF), (uint8_t)(sub >> 8) };