From 6bc400db5eacfb7d2f8a9d9f946f70c2d2c98074 Mon Sep 17 00:00:00 2001 From: dxl <64101226@qq.com> Date: Mon, 19 Oct 2026 22:46:59 +0800 Subject: [PATCH] Fixed: FPGA PWM clock timing failed to meet the 400 MHz requirement. Following discussions and debugging with the hardware engineer, the PWM clock frequency was reduced from 400 MHz to 200 MHz. Subsequent testing confirmed that voltage regulation remained largely unaffected. --- fpga/pm5/fpga_pm5_top.v | 47 +++++++++++++++++++++++++++-------------- fpga/pm5/gowin.sdc | 1 + fpga/pm5/gowin_rpll.v | 4 ++-- 3 files changed, 34 insertions(+), 18 deletions(-) diff --git a/fpga/pm5/fpga_pm5_top.v b/fpga/pm5/fpga_pm5_top.v index 15aa55df8..7155f97be 100644 --- a/fpga/pm5/fpga_pm5_top.v +++ b/fpga/pm5/fpga_pm5_top.v @@ -25,7 +25,7 @@ module fpga_top ( input cross_lo, input spi_mosi, input ssp_dout, - input module_sel, // 选择模块,1=HF,0=LF + input module_sel, // module select: 1 = HF, 0 = LF output ssp_din, output ssp_frame, @@ -41,45 +41,60 @@ module fpga_top ( output dbg2, output dbgled, - output clk_gate, //门控输出,控制切断外部13.56m - output pwr_pwm, //升压器输出,pwm控制升压电压 - output pan_en, //模拟供电使能 - output pdp_en //升压器使能 + output clk_gate, // gates the external 13.56 MHz clock + output pwr_pwm, // boost converter PWM, sets the driver supply voltage + output pan_en, // analog supply enable + output pdp_en // boost converter enable ); - wire ce_lf = ~module_sel; //高启用,低重置 - wire ce_hf = module_sel; //高启用,低重置 + wire ce_lf = ~module_sel; // enable, active high; a low level holds the module in reset + wire ce_hf = module_sel; // enable, active high; a low level holds the module in reset //-----------------------------------------GATE------------------------- - //门控使能信号同步到输入时钟域,避免亚稳态 + // Synchronise the gate enable into the input clock domain against metastability reg gate_en_sync1, gate_en_sync2; always @(posedge ck_1356meg) begin gate_en_sync1 <= gate_en; gate_en_sync2 <= gate_en_sync1; end - assign clk_gate = ~gate_en_sync2;//这里取反是因为外部门控是低有效的 + assign clk_gate = ~gate_en_sync2; // inverted, the external gate is active low //-----------------------------------------PWM-------------------------- + // CLKOUT is 200 MHz: 4096 steps at 5 ns keep the resolution, at a 20.48 us + // period. 400 MHz does not close the 12 bit carry chain at 2.5 ns. Gowin_rPLL pwr_pwm_pll( .clkout(pwr_pwm_pll_clko), //output clkout .clkin(ck_1356meg) //input clkin ); - wire [11:0] pwm_duty_lf; // LF 模块的 PWM 占空比输出 - wire [11:0] pwm_duty_hf; // HF 模块的 PWM 占空比输出 + wire [11:0] pwm_duty_lf; // PWM duty from the LF module + wire [11:0] pwm_duty_hf; // PWM duty from the HF module - wire [11:0] pwm_duty; // PWM占空比,实际上是高电平长度,和4096做比例 + wire [11:0] pwm_duty; // low-level count of the 4096-step PWM period reg [11:0] pwm_cnt= 12'h0; - always @(posedge pwr_pwm_pll_clko) pwm_cnt <= pwm_cnt + 1'b1; //计数器 - assign pwr_pwm = (pwm_cnt > pwm_duty); //pwm输出 + // pwm_duty is from the SPI clock domain; resample it into the PWM domain + // so a duty update is never sampled mid transition. + reg [11:0] pwm_duty_meta, pwm_duty_sync; + always @(posedge pwr_pwm_pll_clko) begin + pwm_duty_meta <= pwm_duty; + pwm_duty_sync <= pwm_duty_meta; + end + + // Register the output; the bare comparator glitches on every count edge. + reg pwr_pwm_r; + always @(posedge pwr_pwm_pll_clko) begin + pwm_cnt <= pwm_cnt + 1'b1; // counter + pwr_pwm_r <= (pwm_cnt > pwm_duty_sync); // PWM output + end + assign pwr_pwm = pwr_pwm_r; assign pan_en = 1'b1; assign pdp_en = 1'b1; - assign pwr_hi = 1'bZ; //使用外部门控时禁用PWRHI,由于是并联的,需要高阻 + assign pwr_hi = 1'bZ; // PWRHI is replaced by the external gate; the two are wired in parallel, so float it assign dbgled = 1'b1; - assign dbg2 = 1'bZ; // 未使用 + assign dbg2 = 1'bZ; // not used fpga_lf uut_lf ( .pck0(pck0), diff --git a/fpga/pm5/gowin.sdc b/fpga/pm5/gowin.sdc index 0d5281899..c0fb0e70a 100644 --- a/fpga/pm5/gowin.sdc +++ b/fpga/pm5/gowin.sdc @@ -7,5 +7,6 @@ create_clock -name CLK_SPI -period 250 -waveform {0 125} [get_ports {spi_sck}] create_clock -name CLK_NCS -period 1000 -waveform {0 500} [get_ports {spi_ncs}] create_clock -name clk24 -period 41.667 -waveform {0 20.834} [get_ports {pck0}] create_clock -name clk1356 -period 73.746 -waveform {0 36.873} [get_ports {ck_1356meg}] +create_clock -name pwr_pwm_clk -period 5 [get_nets {pwr_pwm_pll_clko}] set_clock_groups -asynchronous -group [get_clocks {clk1356}] -group [get_clocks {clk24}] -group [get_clocks {CLK_SPI}] -group [get_clocks {CLK_NCS}] report_timing -setup -from_clock [get_clocks {clk1356}] -to [get_ports {pwr_hi}] diff --git a/fpga/pm5/gowin_rpll.v b/fpga/pm5/gowin_rpll.v index e2a4d3d24..de7dd6a3d 100644 --- a/fpga/pm5/gowin_rpll.v +++ b/fpga/pm5/gowin_rpll.v @@ -47,11 +47,11 @@ rPLL rpll_inst ( defparam rpll_inst.FCLKIN = "13.56"; defparam rpll_inst.DYN_IDIV_SEL = "false"; -defparam rpll_inst.IDIV_SEL = 1; +defparam rpll_inst.IDIV_SEL = 3; defparam rpll_inst.DYN_FBDIV_SEL = "false"; defparam rpll_inst.FBDIV_SEL = 58; defparam rpll_inst.DYN_ODIV_SEL = "false"; -defparam rpll_inst.ODIV_SEL = 2; +defparam rpll_inst.ODIV_SEL = 4; defparam rpll_inst.PSDA_SEL = "0000"; defparam rpll_inst.DYN_DA_EN = "false"; defparam rpll_inst.DUTYDA_SEL = "1000";