pm5: hw bwm powersave
New `hw bwm powersave [on|off]` (CMD_PM5_BWM_POWERSAVE 0x0181) shows or sets the ESP's persisted power-save switch (companion Proxmark5_BWM_esp32 PR: DFS, light sleep and slow advertising after a 30 s fast phase, or the stock always-on behaviour), so the two can be A/B measured and the saving turned off when chasing a link problem. `hw status` prints the state next to the BWM firmware version. Both module queries in `hw status` are time-bounded (version 2 x 800 ms, power save 300 ms): a module that is silent, or a firmware without the command, cannot push the report past the client's timeout. Verified on hardware: state read/set/persist across an ESP reboot, `hw status` after 4, 15 and 40 s idle in power-save mode and after 6 s idle with it off. Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
This commit is contained in:
1 parent
4f4acedbdd
commit
552276c75f
8 files changed
+148
-11
No files matched your search
+54
-1
@@ -697,11 +697,64 @@ static int CmdBwmName(const char *Cmd) {
|
||||
return PM3_SUCCESS;
|
||||
}
|
||||
|
||||
static int CmdBwmPowerSave(const char *Cmd) {
|
||||
// Positional sub-action (no dashes): hw bwm powersave [on | off]; no verb shows the state
|
||||
char verb[16] = {0};
|
||||
sscanf(Cmd, "%15s", verb);
|
||||
bool on = (strcmp(verb, "on") == 0);
|
||||
bool off = (strcmp(verb, "off") == 0);
|
||||
bool show = (verb[0] == 0);
|
||||
|
||||
if (!on && !off && !show) {
|
||||
// Not a recognised sub-action: render help (also serves -h), or error on
|
||||
// a stray token, then stop.
|
||||
CLIParserContext *ctx;
|
||||
CLIParserInit(&ctx, "hw bwm powersave",
|
||||
"Show or set the BWM (ESP32) power-save switch, stored on the BWM in NVS.\n"
|
||||
"Default is " _GREEN_("on") ": the ESP scales its clock down, light-sleeps between\n"
|
||||
"link traffic, and after 30 s of fast advertising (boot, disconnect) advertises\n"
|
||||
"once a second. " _YELLOW_("off") " pins it at full clock, no sleep, fast advertising\n"
|
||||
"throughout. Applies at once and survives reboots. PM5 only.",
|
||||
"hw bwm powersave --> show the current state\n"
|
||||
"hw bwm powersave off --> stock always-on behaviour\n"
|
||||
"hw bwm powersave on --> re-enable power saving");
|
||||
void *argtable[] = {
|
||||
arg_param_begin,
|
||||
arg_param_end
|
||||
};
|
||||
CLIExecWithReturn(ctx, Cmd, argtable, true);
|
||||
CLIParserFree(ctx);
|
||||
PrintAndLogEx(WARNING, "specify " _YELLOW_("on") ", " _YELLOW_("off") " or nothing to show the state");
|
||||
return PM3_EINVARG;
|
||||
}
|
||||
|
||||
uint8_t payload[2] = { show ? BWM_POWERSAVE_ACTION_GET : BWM_POWERSAVE_ACTION_SET, on ? 1 : 0 };
|
||||
clearCommandBuffer();
|
||||
SendCommandNG(CMD_PM5_BWM_POWERSAVE, payload, show ? 1 : 2);
|
||||
PacketResponseNG resp;
|
||||
if (WaitForResponseTimeout(CMD_PM5_BWM_POWERSAVE, &resp, 5000) == false) {
|
||||
PrintAndLogEx(WARNING, "command timeout (is this a PM5 with a responsive BWM?)");
|
||||
return PM3_ETIMEOUT;
|
||||
}
|
||||
if (resp.status == PM3_ENOTIMPL) {
|
||||
PrintAndLogEx(WARNING, "firmware built without BWM link support");
|
||||
return resp.status;
|
||||
}
|
||||
if (resp.status != PM3_SUCCESS || resp.length < 1) {
|
||||
PrintAndLogEx(FAILED, "BWM did not answer the power-save command (BWM firmware too old?)");
|
||||
return (resp.status != PM3_SUCCESS) ? resp.status : PM3_EFAILED;
|
||||
}
|
||||
bool state = (resp.data.asBytes[0] != 0);
|
||||
PrintAndLogEx(SUCCESS, "BWM power save..... %s", state ? _GREEN_("on") : _YELLOW_("off"));
|
||||
return PM3_SUCCESS;
|
||||
}
|
||||
|
||||
static command_t BwmCommandTable[] = {
|
||||
{"help", CmdHelpBwm, IfBwm, "This help"},
|
||||
{"help", CmdHelpBwm, AlwaysAvailable, "This help"},
|
||||
{"autooff", CmdBwmAutoOff, IfBwm, "Toggle auto power-off on USB unplug"},
|
||||
{"charge", CmdBwmCharge, IfBwm, "Enable/disable battery charging (one-shot)"},
|
||||
{"name", CmdBwmName, IfBwm, "Get/set the BWM BLE advertising name"},
|
||||
{"powersave", CmdBwmPowerSave, IfBwm, "Show/set the BWM power-save switch (DFS, light sleep, slow adv)"},
|
||||
{"setcap", CmdBwmSetCap, IfBwm, "Set fuel-gauge design capacity (run once after battery change)"},
|
||||
{"upgrade", CmdBWMUpgrade, IfBwm, "Reflash BWM (ESP32) firmware over the BWM link, no header"},
|
||||
{"vchg", CmdBwmVchg, IfBwm, "Set charger charge-voltage target (default 4100 mV)"},
|
||||
|
||||
Reference in new issue
Block a user