ADD: BWM status includes AW32001ECSR registerd, Charging set to 256mAh and keeps BWM safety guards for temperature
This commit is contained in:
4 files changed
+130
-1
No files matched your search
@@ -1500,6 +1500,47 @@ static int CmdTearoff(const char *Cmd) {
|
||||
return handle_tearoff(¶ms, !silent);
|
||||
}
|
||||
|
||||
static int CmdBwmCharge(const char *Cmd) {
|
||||
CLIParserContext *ctx;
|
||||
CLIParserInit(&ctx, "hw bwmcharge",
|
||||
"Enable or disable BWM battery charging by clearing/setting the\n"
|
||||
"AW32001E charge-enable bit (CEB, REG01[3]). PM5 only.\n"
|
||||
_RED_("One-shot:") " the charger watchdog reverts this after ~160 s unless\n"
|
||||
"serviced, so charging may stop on its own. Use to nudge a top-up.",
|
||||
"hw bwmcharge --> enable charging\n"
|
||||
"hw bwmcharge --off --> disable charging");
|
||||
|
||||
void *argtable[] = {
|
||||
arg_param_begin,
|
||||
arg_lit0(NULL, "off", "disable charging (default is enable)"),
|
||||
arg_param_end
|
||||
};
|
||||
CLIExecWithReturn(ctx, Cmd, argtable, true);
|
||||
bool disable = arg_get_lit(ctx, 1);
|
||||
CLIParserFree(ctx);
|
||||
|
||||
uint8_t payload = disable ? 0 : 1;
|
||||
PrintAndLogEx(INFO, "%s BWM battery charging...", disable ? "Disabling" : "Enabling");
|
||||
|
||||
clearCommandBuffer();
|
||||
SendCommandNG(CMD_PM5_BWM_CHARGE_EN, &payload, sizeof(payload));
|
||||
PacketResponseNG resp;
|
||||
if (WaitForResponseTimeout(CMD_PM5_BWM_CHARGE_EN, &resp, 2500) == false) {
|
||||
PrintAndLogEx(WARNING, "command timeout (is this a PM5 with a BWM fitted?)");
|
||||
return PM3_ETIMEOUT;
|
||||
}
|
||||
if (resp.status != PM3_SUCCESS) {
|
||||
PrintAndLogEx(FAILED, "charger did not respond (check BWM present)");
|
||||
return resp.status;
|
||||
}
|
||||
PrintAndLogEx(SUCCESS, "Charging %s. Verify with " _YELLOW_("hw status") ".",
|
||||
disable ? "disabled" : "enabled");
|
||||
if (disable == false) {
|
||||
PrintAndLogEx(HINT, "Reverts on the charger watchdog (~160 s) if not serviced.");
|
||||
}
|
||||
return PM3_SUCCESS;
|
||||
}
|
||||
|
||||
static int CmdBwmSetCap(const char *Cmd) {
|
||||
CLIParserContext *ctx;
|
||||
CLIParserInit(&ctx, "hw bwmsetcap",
|
||||
@@ -2009,6 +2050,7 @@ static command_t CommandTable[] = {
|
||||
{"standalone", CmdStandalone, IfPm3Present, "Start installed standalone mode on device"},
|
||||
{"tia", CmdTia, IfPm3Present, "Trigger a Timing Interval Acquisition to re-adjust the RealTimeCounter divider"},
|
||||
{"bwmsetcap", CmdBwmSetCap, IfPm5, "Set BWM fuel-gauge design capacity (PM5, run once after battery change)"},
|
||||
{"bwmcharge", CmdBwmCharge, IfPm5, "Enable/disable BWM battery charging (PM5, one-shot)"},
|
||||
{"tune", CmdTune, IfPm3Lf, "Measure tuning of device antenna"},
|
||||
{"decay", CmdDecay, IfPm3Present, "Measure HF antenna decay after field-off"},
|
||||
{NULL, NULL, NULL, NULL}
|
||||
|
||||
Reference in new issue
Block a user