- revised CV programming especially writing - Core 1 is only started when valid package with correct address is received - Extended addresses are now correctly verified and implemented - Base PWM measurement is now done on core0 and checked for automatically in cv_setup_check() - Moved Motor PWM, GPIO, ADC to core0 - Implemented inverted direction mode (CV_29) according to DCC-Standards - Limited feed-forward parameters y_2 to max_output/y_1 - k_p gain slopes are now calculated on initialization - k_p gain parameters are also in pid parameter struct now - Revised init_pid() - Implemented Packet timeout check (CV_11) - 16Bit and 32Bit CVs now always have the highest bytes as the lowest array index to accommodate get_XXbit_CV() functions
45 lines
1.8 KiB
C
45 lines
1.8 KiB
C
//////////////////////////
|
|
// RP2040-Decoder //
|
|
// Gabriel Koppenstein //
|
|
// shared.h //
|
|
//////////////////////////
|
|
|
|
#pragma once
|
|
#include "string.h"
|
|
#include "pico/float.h"
|
|
#include "pico/stdlib.h"
|
|
#include "pico/multicore.h"
|
|
#include "pico/printf.h"
|
|
#include "hardware/pwm.h"
|
|
#include "hardware/adc.h"
|
|
#include "hardware/flash.h"
|
|
#include "hardware/irq.h"
|
|
#define _125M 125000000
|
|
#define DCC_INPUT_PIN 21u
|
|
#define MOTOR_FWD_PIN 23u
|
|
#define MOTOR_REV_PIN 22u
|
|
#define FWD_V_EMF_ADC_PIN 28u
|
|
#define REV_V_EMF_ADC_PIN 29u
|
|
//Aux output pins (GPIO 24,25,26,27)
|
|
#define AUX_PIN_MASK (1u<<24) | (1u<<25) | (1u<<26) | (1u<<27)
|
|
//GPIO pins configured as inputs (Input functionality not implemented yet)
|
|
#define GPIO_INPUT_MASK 0b00000000000000000000000000000000
|
|
//GPIO pins configured as outputs
|
|
#define GPIO_OUTPUT_MASK 0b00000000000000000000000000000000
|
|
//GPIO pin mask to prevent setting illegal GPIOs (ADC, Motor, DCC Input Pin)
|
|
#define GPIO_ILLEGAL_MASK (1u<<DCC_INPUT_PIN) | (1u<<MOTOR_FWD_PIN) | (1u<<MOTOR_REV_PIN) | (1u<<FWD_V_EMF_ADC_PIN) | (1u<<REV_V_EMF_ADC_PIN)
|
|
//GPIO pin mask with allowed outputs (AUX & GPIO (configured as outputs))
|
|
#define GPIO_ALLOWED_OUTPUTS (GPIO_OUTPUT_MASK|AUX_PIN_MASK) & ~(GPIO_ILLEGAL_MASK)
|
|
#define FLASH_TARGET_OFFSET (PICO_FLASH_SIZE_BYTES-FLASH_SECTOR_SIZE) //This Offset should be far enough away from program data
|
|
|
|
extern repeating_timer_t pid_control_timer;
|
|
extern repeating_timer_t speed_helper_timer;
|
|
extern const uint8_t *CV_ARRAY_FLASH;
|
|
void core1_entry();
|
|
float measure(uint8_t total_iterations,
|
|
uint8_t measurement_delay_us,
|
|
uint8_t l_side_arr_cutoff,
|
|
uint8_t r_side_arr_cutoff,
|
|
bool direction);
|
|
uint32_t get_32bit_CV (uint16_t CV_start_index);
|
|
uint16_t get_16bit_CV (uint16_t CV_start_index); |