327 lines
12 KiB
C
327 lines
12 KiB
C
//////////////////////////
|
|
// RP2040-Decoder //
|
|
// Gabriel Koppenstein //
|
|
// core1.c //
|
|
//////////////////////////
|
|
|
|
#include "core1.h"
|
|
|
|
struct repeating_timer pid_control_timer, speed_helper_timer;
|
|
|
|
|
|
// Get speed_step_table_index depending on speed_step
|
|
uint8_t get_speed_step_table_index_of_speed_step(uint8_t speed_step) {
|
|
if (speed_step > 127) {
|
|
// Forward
|
|
if (speed_step == 128) {
|
|
return 0;
|
|
}
|
|
else {
|
|
return (speed_step - 129);
|
|
}
|
|
}
|
|
else {
|
|
// Reverse
|
|
if (speed_step == 0) {
|
|
return 0;
|
|
}
|
|
else {
|
|
return (speed_step - 1);
|
|
}
|
|
}
|
|
}
|
|
|
|
|
|
// This function gets called every x milliseconds where x is CV_175.
|
|
// The purpose of this function is to implement a time delay in acceleration or deceleration
|
|
bool speed_helper(struct repeating_timer *t) {
|
|
// pid->setpoint only gets adjusted when the speed_helper_counter is equal to the accel_rate/decel_rate
|
|
// -> Time for 1 Speed Step := (speed_helper timer delay)*(accel_rate) or CV_175*CV_3 or CV_175*CV_4
|
|
pid_params *pid = (pid_params *) (t->user_data);
|
|
uint8_t accel_rate = CV_ARRAY_FLASH[2];
|
|
uint8_t decel_rate = CV_ARRAY_FLASH[3];
|
|
static uint8_t speed_helper_counter;
|
|
static uint8_t speed_table_index;
|
|
|
|
// Get speed_step_table_end_index corresponding to current speed_step_target
|
|
uint8_t speed_step_table_end_index = get_speed_step_table_index_of_speed_step(speed_step_target);
|
|
bool direction_changed = get_direction_of_speed_step(speed_step_target) !=
|
|
get_direction_of_speed_step(speed_step_target_prev);
|
|
|
|
if (pid->speed_step_target == 129 || pid->speed_step_target == 1) {
|
|
// Emergency Stop
|
|
speed_table_index = 0;
|
|
speed_helper_counter = 0;
|
|
pid->setpoint = pid->speed_table[speed_table_index];
|
|
}
|
|
else if (speed_step_table_end_index > speed_table_index && speed_helper_counter == accel_rate) {
|
|
// Acceleration
|
|
if (!accel_rate) speed_table_index = speed_step_table_end_index; // directly accelerate to end target speed
|
|
else speed_table_index++;
|
|
pid->setpoint = pid->speed_table[speed_table_index];
|
|
speed_helper_counter = 0;
|
|
}
|
|
|
|
else if (speed_step_table_end_index < speed_table_index && speed_helper_counter == decel_rate) {
|
|
// Deceleration
|
|
if (!decel_rate) speed_table_index = speed_step_table_end_index; // directly decelerate to end target speed
|
|
else speed_table_index--;
|
|
pid->setpoint = pid->speed_table[speed_table_index];
|
|
speed_helper_counter = 0;
|
|
}
|
|
|
|
else if (direction_changed) {
|
|
// Change of direction while decelerating -> jump to most recent speed_step without delay (other direction)
|
|
speed_table_index = speed_step_table_end_index;
|
|
pid->setpoint = pid->speed_table[speed_table_index];
|
|
speed_helper_counter = 0;
|
|
}
|
|
|
|
else if (speed_step_table_end_index != speed_table_index) {
|
|
// Acceleration/Deceleration "scheduled"
|
|
speed_helper_counter++;
|
|
}
|
|
|
|
else {
|
|
// Target reached -> Reset Counter
|
|
speed_helper_counter = 0;
|
|
}
|
|
|
|
// return true to schedule the repeating timer again
|
|
return true;
|
|
}
|
|
|
|
|
|
// Helper function to adjust pwm level/duty cycle.
|
|
void adjust_pwm_level(uint16_t level, pid_params *pid) {
|
|
if (get_direction_of_speed_step(speed_step_target) == true) {
|
|
// Forward
|
|
pwm_set_gpio_level(MOTOR_REV_PIN, 0);
|
|
pwm_set_gpio_level(MOTOR_FWD_PIN, level);
|
|
}
|
|
else {
|
|
// Reverse
|
|
pwm_set_gpio_level(MOTOR_FWD_PIN, 0);
|
|
pwm_set_gpio_level(MOTOR_REV_PIN, level);
|
|
}
|
|
}
|
|
|
|
|
|
// Update feed-forward slope/gradient for both directions
|
|
void update_m(pid_params *pid) {
|
|
pid->m_fwd = (pid->y_2_fwd - pid->y_1_fwd) / (pid->x_2_fwd - pid->x_1_fwd);
|
|
pid->m_rev = (pid->y_2_rev - pid->y_1_rev) / (pid->x_2_rev - pid->x_1_rev);
|
|
}
|
|
|
|
|
|
// Update feedforward function value y_2 in both directions
|
|
void update_y(pid_params *pid, float i) {
|
|
if (get_direction_of_speed_step(speed_step_target) == true) {
|
|
// Forward
|
|
pid->y_2_fwd += i * pid->k_ff;
|
|
// Limit y_2_fwd
|
|
if (pid->y_2_fwd > pid->max_output) pid->y_2_fwd = pid->max_output;
|
|
else if (pid->y_2_fwd < pid->y_1_fwd) pid->y_2_fwd = pid->y_1_fwd;
|
|
}
|
|
else {
|
|
// Reverse
|
|
pid->y_2_rev += i * pid->k_ff;
|
|
// Limit y_2_rev
|
|
if (pid->y_2_rev > pid->max_output) pid->y_2_rev = pid->max_output;
|
|
else if (pid->y_2_rev < pid->y_1_rev) pid->y_2_rev = pid->y_1_rev;
|
|
}
|
|
update_m(pid);
|
|
}
|
|
|
|
|
|
// Returns feedforward value corresponding to current setpoint
|
|
float get_ff_val(pid_params *pid) {
|
|
float val;
|
|
if (get_direction_of_speed_step(speed_step_target) == true) {
|
|
// Forward
|
|
val = pid->m_fwd * ((float) pid->setpoint - pid->x_1_fwd) + pid->y_1_fwd;
|
|
}
|
|
else {
|
|
// Reverse
|
|
val = pid->m_rev * ((float) pid->setpoint - pid->x_1_rev) + pid->y_1_rev;
|
|
}
|
|
return val;
|
|
}
|
|
|
|
|
|
// Returns proportional gain value corresponding to current setpoint
|
|
float get_kp(pid_params *pid) {
|
|
float sp = (float) pid->setpoint;
|
|
if (sp < pid->k_p_x_1) {
|
|
return pid->k_p_m_1 * sp + pid->k_p_y_0;
|
|
}
|
|
else {
|
|
return pid->k_p_m_2 * (sp - pid->k_p_x_1) + pid->k_p_y_1;
|
|
}
|
|
}
|
|
|
|
|
|
// PID controller function gets called every x milliseconds where x is CV_49 aka sampling time (pid->t)
|
|
bool pid_control(struct repeating_timer *t) {
|
|
// Cast (void *) to (pid_params *)
|
|
pid_params *pid = (pid_params *) (t->user_data);
|
|
|
|
// Acceleration from standstill or change in direction -> reset previous derivative, error and integral parts
|
|
bool direction_changed = get_direction_of_speed_step(speed_step_target) !=
|
|
get_direction_of_speed_step(speed_step_target_prev);
|
|
if ((!pid->setpoint_prev && !pid->setpoint) || direction_changed) {
|
|
pid->d_prev = 0.0f;
|
|
pid->i_prev = 0.0f;
|
|
pid->e_prev = 0.0f;
|
|
}
|
|
|
|
// Get feed-forward and proportional gain values
|
|
float feed_fwd = get_ff_val(pid);
|
|
pid->k_p = get_kp(pid);
|
|
|
|
// Measure BEMF voltage and compute error
|
|
pid->measurement = measure(pid->msr_total_iterations,
|
|
pid->msr_delay_in_us,
|
|
pid->l_side_arr_cutoff,
|
|
pid->r_side_arr_cutoff,
|
|
get_direction_of_speed_step(speed_step_target));
|
|
|
|
float measurement_corrected = pid->measurement - pid->adc_offset;
|
|
float e = (float) pid->setpoint - measurement_corrected;
|
|
|
|
// Proportional part, integral part and derivative part (including digital low-pass-filter with time constant tau)
|
|
float p = pid->k_p * e;
|
|
float i = pid->ci_0 * (e + pid->e_prev) + pid->i_prev;
|
|
float d = pid->cd_0 * (pid->measurement - pid->measurement_prev) + pid->cd_1 * pid->d_prev;
|
|
|
|
// Check for limits on the integral part
|
|
if (i > pid->int_lim_max)i = pid->int_lim_max;
|
|
else if (i < pid->int_lim_min)i = pid->int_lim_min;
|
|
|
|
// Sum feed forward + all controller terms (p+i+d). Limit Output from 0% to 100% duty cycle
|
|
float output = feed_fwd + p + i + d;
|
|
if (output < 0 || !pid->setpoint) output = 0.0f;
|
|
else if (output > pid->max_output) output = pid->max_output;
|
|
|
|
if (LOGLEVEL >= 1) {
|
|
static int counter = 0;
|
|
counter++;
|
|
if (counter > 100) {
|
|
LOG(1, "pid error(%f) output(%f)\n", e, output);
|
|
counter = 0;
|
|
}
|
|
}
|
|
|
|
// Set PWM Level and discard results in adc fifo
|
|
adjust_pwm_level((uint16_t) roundf(output), pid);
|
|
adc_fifo_drain();
|
|
|
|
// Check for High or Low Integrator values -> Update x,y values of feedforward function
|
|
if ((output < pid->max_output && output > pid->max_output / 2) &&
|
|
((i > pid->int_lim_max / 2) || (i < pid->int_lim_min / 2))) {
|
|
update_y(pid, i);
|
|
}
|
|
|
|
// Save previous error, integrator, differentiator, direction, setpoint and measured value also sum error to e_sum
|
|
pid->e_prev = e;
|
|
pid->i_prev = i;
|
|
pid->d_prev = d;
|
|
pid->setpoint_prev = pid->setpoint;
|
|
pid->measurement_prev = pid->measurement;
|
|
|
|
// return true to schedule the repeating timer again
|
|
return true;
|
|
}
|
|
|
|
|
|
// PID controller and measurement parameter, and speed_table initialization
|
|
void init_pid(pid_params *pid) {
|
|
// Measurement variables initialization
|
|
pid->adc_offset = (float) CV_ARRAY_FLASH[171];
|
|
pid->msr_total_iterations = CV_ARRAY_FLASH[60];
|
|
pid->msr_delay_in_us = CV_ARRAY_FLASH[61];
|
|
pid->l_side_arr_cutoff = CV_ARRAY_FLASH[62];
|
|
pid->r_side_arr_cutoff = CV_ARRAY_FLASH[63];
|
|
|
|
// Speed table initialization
|
|
// Calculate speed setpoint table according to V_min, V_max and V_mid CVs
|
|
double v_min = (double) CV_ARRAY_FLASH[1];
|
|
double v_mid = (double) CV_ARRAY_FLASH[5] * 16;
|
|
double v_max = (double) CV_ARRAY_FLASH[4] * 16;
|
|
|
|
LOG(1, "speedtable min(%f) mid(%f) max(%f)\n", v_min, v_mid, v_max);
|
|
|
|
double delta_x = 63;
|
|
double m_1 = (v_mid - v_min) / delta_x;
|
|
double m_2 = (v_max - v_mid) / delta_x;
|
|
pid->speed_table[0] = 0;
|
|
for (uint8_t i = 1; i < 64; ++i) {
|
|
pid->speed_table[i] = (uint16_t) lround(m_1 * (i - 1) + v_min);
|
|
}
|
|
for (uint8_t i = 64; i < 127; ++i) {
|
|
pid->speed_table[i] = (uint16_t) lround(m_2 * (i - 63) + v_mid);
|
|
}
|
|
|
|
// Controller constants initialization
|
|
pid->k_i = (float) CV_ARRAY_FLASH[49] / 10;
|
|
pid->k_d = (float) CV_ARRAY_FLASH[50] / 10000;
|
|
pid->tau = (float) CV_ARRAY_FLASH[47] / 1000;
|
|
pid->t = (float) CV_ARRAY_FLASH[48] / 1000;
|
|
pid->ci_0 = (pid->k_i * pid->t) / 2;
|
|
pid->cd_0 = -(2 * pid->k_d) / (2 * pid->tau + pid->t);
|
|
pid->cd_1 = (2 * pid->tau - pid->t) / (2 * pid->tau + pid->t);
|
|
pid->int_lim_max = 10 * (float) CV_ARRAY_FLASH[51];
|
|
pid->int_lim_min = -10 * (float) CV_ARRAY_FLASH[52];
|
|
pid->k_ff = (float) CV_ARRAY_FLASH[46] / 10000;
|
|
pid->max_output = (float) (_125M / (CV_ARRAY_FLASH[8] * 100 + 10000));
|
|
pid->x_1_rev = 0.0f;
|
|
pid->x_1_fwd = 0.0f;
|
|
pid->y_1_fwd = (float) get_16bit_CV(175);
|
|
pid->y_1_rev = (float) get_16bit_CV(177);
|
|
pid->x_2_rev = (float) pid->speed_table[126];
|
|
pid->x_2_fwd = (float) pid->speed_table[126];
|
|
|
|
// Controller variables initialization
|
|
pid->y_2_fwd = pid->max_output;
|
|
pid->y_2_rev = pid->max_output;
|
|
pid->measurement = 0.0f;
|
|
pid->measurement_prev = 0.0f;
|
|
pid->e_prev = 0.0f;
|
|
pid->i_prev = 0.0f;
|
|
pid->d_prev = 0.0f;
|
|
pid->setpoint = 0;
|
|
|
|
// Gain scheduling initialization
|
|
pid->k_p_x_1_shift = (float) CV_ARRAY_FLASH[59] / 255.0f;
|
|
pid->k_p_x_1 = (float) pid->speed_table[126] * pid->k_p_x_1_shift;
|
|
pid->k_p_x_2 = (float) pid->speed_table[126] * (1.0f - pid->k_p_x_1_shift);
|
|
pid->k_p_y_0 = (float) get_16bit_CV(53) / 100.0f;
|
|
pid->k_p_y_1 = (float) get_16bit_CV(55) / 100.0f;
|
|
pid->k_p_y_2 = (float) get_16bit_CV(57) / 100.0f;
|
|
pid->k_p_m_1 = (pid->k_p_y_1 - pid->k_p_y_0) / pid->k_p_x_1;
|
|
pid->k_p_m_2 = (pid->k_p_y_2 - pid->k_p_y_1) / pid->k_p_x_2;
|
|
|
|
update_m(pid);
|
|
}
|
|
|
|
void core1_entry() {
|
|
LOG(1, "core1 init...\n");
|
|
pid_params pid_parameters;
|
|
pid_params *pid = &pid_parameters;
|
|
init_pid(pid);
|
|
alarm_pool_add_repeating_timer_ms(alarm_pool_create(0, 1),
|
|
CV_ARRAY_FLASH[48],
|
|
pid_control,
|
|
pid,
|
|
&pid_control_timer);
|
|
// Set TIMER_IRQ_0 to highest priority of 0x00
|
|
irq_set_priority(TIMER_IRQ_0, 0x00);
|
|
alarm_pool_add_repeating_timer_ms(alarm_pool_create(1, 1),
|
|
CV_ARRAY_FLASH[174],
|
|
speed_helper,
|
|
pid,
|
|
&speed_helper_timer);
|
|
LOG(1, "core1 done\n");
|
|
while (true);
|
|
}
|