Files
RP2040-Decoder/core0.c
T

674 lines
27 KiB
C

//////////////////////////
// RP2040-Decoder //
// Gabriel Koppenstein //
// core0.c //
//////////////////////////
#include "core0.h"
// XIP_BASE + FLASH_TARGET_OFFSET = "0x101FF000" <- This address need to be smaller than __flash_binary_end stored in RP2040-Decoder.elf.map
const uint8_t *CV_ARRAY_FLASH = (const uint8_t *) (XIP_BASE + FLASH_TARGET_OFFSET);
uint64_t input_bit_buffer = 0;
uint16_t level_table[32] = {0};
absolute_time_t falling_edge_time, rising_edge_time;
// Function returns average of values deviating less than twice the standard deviation from original average
float two_std_dev(const float arr[], uint32_t length) {
// Calculate arithmetic average
float sum = 0;
for (uint32_t i = 0; i < length; ++i) {
sum += arr[i];
}
float x_avg = sum / (float) length;
// Calculate sample variance and sampled standard deviation
sum = 0;
for (uint32_t i = 0; i < length; ++i) {
sum += (arr[i] - x_avg) * (arr[i] - x_avg);
}
float variance = sum / (float) (length - 1);
float std_dev = sqrtf(variance);
// Sum every element that is within two times the sampled standard deviation and compute new average
sum = 0;
uint32_t counter = 0;
for (uint32_t i = 0; i < length; ++i) {
float diff = fabsf(arr[i] - x_avg);
if (diff < std_dev * 2.0f) {
sum += arr[i];
counter++;
}
}
return sum / (float) counter;
}
// Measures constant adc offset and programs the offset into flash
void adc_offset_adjustment(uint32_t n) {
LOG(1, "adc_offset_adjustment");
float offsets_fwd[n];
float offsets_rev[n];
// Set PWM level to 0 just to be sure
pwm_set_gpio_level(MOTOR_FWD_PIN, 0);
pwm_set_gpio_level(MOTOR_REV_PIN, 0);
busy_wait_ms(1000);
// Measure n times in "reverse direction" (GPIO 28)
adc_select_input(2);
adc_run(true);
for (uint32_t i = 0; i < n; i++) {
offsets_rev[i] = (float) adc_fifo_get_blocking();
}
adc_run(false);
adc_fifo_drain();
busy_wait_ms(1000);
// Measure n times in "forward direction" (GPIO 29)
adc_select_input(3);
adc_run(true);
for (uint32_t i = 0; i < n; i++) {
offsets_fwd[i] = (float) adc_fifo_get_blocking();
}
adc_run(false);
adc_fifo_drain();
// Find overall average discarding outliers in measurement
float offset_avg_fwd = two_std_dev(offsets_fwd, n);
float offset_avg_rev = two_std_dev(offsets_rev, n);
float overall_avg = (offset_avg_fwd + offset_avg_rev) / 2;
uint8_t offset = (uint8_t) roundf(overall_avg);
LOG(1, "new adc offset CV[171] (%f): (uint8_t)%d\n", overall_avg, offset);
// Create temporary array -> change CV 172 in temp array -> erase flash -> write temp array to flash
uint8_t CV_ARRAY_TEMP[CV_ARRAY_SIZE];
memcpy(CV_ARRAY_TEMP, CV_ARRAY_FLASH, sizeof(CV_ARRAY_TEMP));
CV_ARRAY_TEMP[171] = offset;
flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE);
flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_TEMP, FLASH_PAGE_SIZE * 2);
}
// Confirmation after writing or verifying a CV
// Works by creating a spike in current consumption, this is detected by the command station
void acknowledge() {
uint16_t max_lvl = _125M / (CV_ARRAY_FLASH[8] * 100 + 10000);
pwm_set_gpio_level(MOTOR_FWD_PIN, max_lvl);
busy_wait_ms(3);
pwm_set_gpio_level(MOTOR_FWD_PIN, 0);
pwm_set_gpio_level(MOTOR_REV_PIN, max_lvl);
busy_wait_ms(3);
pwm_set_gpio_level(MOTOR_REV_PIN, 0);
}
// When bit matches sent byte -> acknowledge()
void verify_cv_bit(uint16_t cv_address, bool bit_val, uint8_t bit_pos) {
uint8_t mask = 0b00000001;
bool res = ((CV_ARRAY_FLASH[cv_address] >> bit_pos) & mask) == bit_val;
if (res) {
acknowledge();
}
}
// When byte matches sent byte -> acknowledge()
void verify_cv_byte(uint16_t cv_address, uint8_t cv_data) {
if (CV_ARRAY_FLASH[cv_address] == cv_data) acknowledge();
}
// CV writing function first erases necessary amount of blocks in flash and then rewrites to flash
void regular_cv_write(uint16_t cv_index, uint8_t cv_data) {
uint8_t CV_ARRAY_TEMP[CV_ARRAY_SIZE];
memcpy(CV_ARRAY_TEMP, CV_ARRAY_FLASH, sizeof(CV_ARRAY_TEMP));
CV_ARRAY_TEMP[cv_index] = cv_data;
flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE);
flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_TEMP, FLASH_PAGE_SIZE * 2);
acknowledge();
}
// There are some exceptions to writing CVs - e.g. writing to a read only CV is not valid - this gets handled here
void write_cv_handler(uint16_t cv_index, uint8_t cv_data) {
switch (cv_index) {
case 0: //CV_1
// CV_1 => Value = 0 is not allowed
if (cv_data == 0 || cv_data > 127)
break;
else
regular_cv_write(cv_index, cv_data);
break;
case 6: //CV_7
// Read only (CV_7 - Version no.)
// ADC offset Adjustment (CV_7; Value = 7);
if (cv_data == 7) {
LOG(1, "trigger adc offset adjustment via cv7 => 7\n");
adc_offset_adjustment(8192);
}
break;
case 7: //CV_8
// Read only (CV_8 - Manufacturer ID)
// Reset all CVs to Default (CV_8; Value = 8)
if (cv_data == 8) {
LOG(1, "reset of flash triggered via cv8 => 8\n");
flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE);
flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_DEFAULT, FLASH_PAGE_SIZE * 2);
}
break;
// CV_17 must have a value between 11000000->(192dec) and 11100111->(231dec) inclusive
// CV_17 == 192 && CV_18 == 0 -> Address = 0 is also not valid and therefore shall not be set
case 16: //CV_17
if ((cv_data < 192 || cv_data > 231) || (CV_ARRAY_FLASH[17] == 0 && cv_data == 192))
break;
else
regular_cv_write(cv_index, cv_data);
break;
case 17: //CV_18
if (CV_ARRAY_FLASH[16] == 192 && cv_data == 0)
break;
else
regular_cv_write(cv_index, cv_data);
break;
// CV_31 & CV_32 Index high byte isn't implemented and shall not be set
case 30: //CV_31
case 31: //CV_32
break;
// Regular CV write is carried out
default:
regular_cv_write(cv_index, cv_data);
}
}
// CV Programming function resets core1 and evaluates the type of programming instruction (e.g. write byte)
void program_mode(uint8_t number_of_bytes, const uint8_t *const byte_array) {
//First check for valid programming command ("address" 112-127)
if (byte_array[number_of_bytes - 1] < 128 && byte_array[number_of_bytes - 1] > 111) {
uint8_t instruction_type_mask = 0b00001100;
uint8_t instruction_type = instruction_type_mask & byte_array[number_of_bytes - 1];
uint8_t cv_address_ms_bits_mask = 0b00000011;
uint16_t cv_address_ms_bits = cv_address_ms_bits_mask & byte_array[number_of_bytes - 1];
uint16_t cv_address = byte_array[number_of_bytes - 2] + (cv_address_ms_bits << 8);
// Before accessing flash, timers and interrupts need to be disabled and core1 needs to be shut down.
if (pid_control_timer.pool) {
alarm_pool_destroy(pid_control_timer.pool);
}
if (speed_helper_timer.pool) {
alarm_pool_destroy(speed_helper_timer.pool);
}
multicore_reset_core1();
uint32_t saved_interrupts = save_and_disable_interrupts();
if (instruction_type == 0b000001000) {
// Verify CV bit instruction
uint8_t bit_pos_mask = 0b00000111;
uint8_t bit_pos = bit_pos_mask & byte_array[number_of_bytes - 3];
uint8_t bit_val_mask = 0b00000001;
uint8_t bit_val_uint = (byte_array[number_of_bytes - 3] >> 3) & bit_val_mask;
bool bit_val = bit_val_uint;
verify_cv_bit(cv_address, bit_val, bit_pos);
}
else if (instruction_type == 0b000000100) {
// Verify CV byte instruction
uint8_t cv_data = byte_array[number_of_bytes - 3];
verify_cv_byte(cv_address, cv_data);
}
else if (instruction_type == 0b000001100) {
// Write CV byte instruction
uint8_t cv_data = byte_array[number_of_bytes - 3];
write_cv_handler(cv_address, cv_data);
}
// Restore interrupts
restore_interrupts(saved_interrupts);
// TODO: verify core1 launch...
multicore_launch_core1(core1_entry);
// TODO: Check busy wait necessity
busy_wait_ms(5);
}
}
// Set outputs according to configuration (PWM on/off, PWM duty cycle/level, ...)
void set_outputs(uint32_t functions_to_set_bitmask) {
// Get outputs with pwm enabled and preset outputs_to_set_PWM variable with resulting GPIO Bitmask
uint32_t PWM_enabled_outputs = get_32bit_CV(111);
uint32_t outputs_to_set_PWM = PWM_enabled_outputs;
// Get enabled output configuration corresponding to set functions and direction
uint32_t outputs_to_set = 0;
uint32_t temp_mask = 1;
for (uint8_t i = 0; i < 32; i++) {
if (temp_mask & functions_to_set_bitmask) {
bool direction = get_direction_of_speed_step(speed_step_target);
outputs_to_set |= get_32bit_CV(i * 8 + 260 - 4 * direction);
}
temp_mask <<= 1;
}
outputs_to_set_PWM &= outputs_to_set; // Outputs with PWM to be enabled
outputs_to_set &= ~outputs_to_set_PWM; // Outputs without PWM to be enabled
// Set regular outputs without PWM, preventing illegal GPIO by masking with GPIO_ALLOWED_OUTPUTS
gpio_put_masked(GPIO_ALLOWED_OUTPUTS, outputs_to_set);
// Set PWM enabled outputs to desired level
temp_mask = 1;
for (uint8_t i = 0; i < 32; ++i) {
if (temp_mask & outputs_to_set_PWM) {
pwm_set_gpio_level(i, level_table[i]);
pwm_gpio_to_channel(i);
pwm_gpio_to_slice_num(i);
}
else if (temp_mask & PWM_enabled_outputs) {
pwm_set_gpio_level(i, 0);
}
temp_mask <<= 1;
}
}
// Update functions F0 - F31 when function command is received or in case of direction change
void update_active_functions(uint32_t new_function_bitmask, uint8_t clr_bit_ind, bool direction_change) {
static uint32_t active_functions;
static uint32_t prev_active_func;
// Outputs depend on direction, therefore on direction change outputs need to be set as configured for the other direction.
if (direction_change) {
// In case of a direction change every output needs to be set according to configuration for the other direction
set_outputs(active_functions);
}
else {
// TODO: improve explanation here...
// In case of a change in active functions only the function group corresponding to the instruction is considered
// Check for changes and set outputs accordingly
new_function_bitmask &= ~(clr_bit_arr[clr_bit_ind]); // Clear every bit except bits corresponding to group of functions
active_functions &= clr_bit_arr[clr_bit_ind]; // Clear bits corresponding to group of functions
active_functions |= new_function_bitmask; // Write bits corresponding to group of functions
uint32_t changes = active_functions ^ prev_active_func; // Checks for changes from previous state
if (changes) set_outputs(active_functions);
prev_active_func = active_functions;
}
}
// Bitwise XOR for all Bytes -> when result is: "0000 0000" error check is passed.
bool error_detection(int8_t number_of_bytes, const uint8_t *const byte_array) {
uint8_t xor_byte = 0;
for (int i = 0; i < number_of_bytes; i++) {
xor_byte = xor_byte ^ byte_array[i];
}
return (0 == xor_byte);
}
// Check for long address. Function returns true for long address.
bool is_long_address(uint8_t number_of_bytes, const uint8_t *const byte_array) {
if ((byte_array[number_of_bytes - 1] >> 6) == 0b00000011) {
return true;
}
return false;
}
// First checks for idle message and then evaluates address included in byte_array[] which contains the received DCC message
bool address_evaluation(uint8_t number_of_bytes, const uint8_t *const byte_array) {
// Check for idle message
if (byte_array[number_of_bytes - 1] == 255) {
return false;
}
// Long/extended address decoder configuration (CV_29 Bit5)
bool CV_29_bit5 = (CV_ARRAY_FLASH[28] & 0b00100000) >> 5;
uint16_t read_address;
// Check if decoder is configured to receive long/extended address (CV_29 Bit5 set)
if (CV_29_bit5) {
// Check DCC message for long address format
if (is_long_address(number_of_bytes, byte_array)) {
// DCC message received has long address format
// start of transmission -> address_byte_1 -> address_byte_0 -> ... -> end of transmission
uint16_t address_byte_1 = (byte_array[number_of_bytes - 1]) - 192; // Remove long address identifier bits
uint16_t address_byte_0 = (byte_array[number_of_bytes - 2]);
read_address = (address_byte_1 << 8) + address_byte_0;
uint16_t long_address = get_16bit_CV(16) & 0x3FFF; // &Mask to remove long address identifier bits
return (long_address == read_address);
}
else {
// DCC message received does not have long address format
return false;
}
}
else {
// Else decoder is configured to receive short address (CV_29 Bit5 not set)
// Short address message:
// start of transmission -> address_byte_0 -> ... -> end of transmission
read_address = (byte_array[number_of_bytes - 1]);
return (CV_ARRAY_FLASH[0] == read_address);
}
}
// Evaluate the type of instruction
void instruction_evaluation(const uint8_t number_of_bytes, const uint8_t *const byte_array) {
// start of transmission -> ... -> command_byte_n -> ... -> command_byte_0 -> ... -> end of transmission
// The position of command bytes depend on whether the address is long or not
uint8_t command_byte_n;
uint8_t command_byte_start_index;
if (is_long_address(number_of_bytes, byte_array)) {
command_byte_start_index = number_of_bytes - 3;
}
else {
command_byte_start_index = number_of_bytes - 2;
}
command_byte_n = byte_array[command_byte_start_index];
// 0011-1111 (128 Speed Step Control) - 2 Byte length
if (command_byte_n == 0b00111111) {
speed_step_target_prev = speed_step_target;
speed_step_target = byte_array[command_byte_start_index - 1];
// Check for direction change
bool direction_changed = get_direction_of_speed_step(speed_step_target) !=
get_direction_of_speed_step(speed_step_target_prev);
// In case of a direction change, functions need to be updated because functions depend on direction
if (direction_changed) {
update_active_functions(0, 0, true);
}
}
// 10XX-XXXX (Function Group Instruction)
else if (command_byte_n >> 6 == 0b00000010) {
switch (command_byte_n >> 4) {
case 0b00001011: // F5-F8
update_active_functions((command_byte_n << 5), 1, false);
break;
case 0b00001010: // F9-F12
update_active_functions((command_byte_n << 9), 2, false);
break;
default: // F0-F4
update_active_functions((((command_byte_n & 0b00001111) << 1) + ((command_byte_n & 0b00010000) >> 4)),
0, false);
break;
}
}
//Feature Expansion Instruction 110X-XXXX
else if (command_byte_n >> 5 == 0b00000110) {
switch (command_byte_n) {
case 0b11011110: // F13-F20
update_active_functions((byte_array[command_byte_start_index - 1] << 13), 3, false);
break;
case 0b11011111: // F21-F28
update_active_functions((byte_array[command_byte_start_index - 1] << 21), 4, false);
break;
case 0b11011000: // F29-F31
update_active_functions((byte_array[command_byte_start_index - 1] << 29), 5, false);
break;
default:
break;
}
}
}
// Check for reset message - When reset message is found, stop the motor and disable all functions.
bool reset_message_check(uint8_t number_of_bytes, const uint8_t *const byte_array) {
if (byte_array[number_of_bytes - 1] == 0b00000000 && byte_array[number_of_bytes - 2] == 0b00000000) {
uint32_t speed_step = 1;
multicore_fifo_push_blocking(speed_step); // Emergency Stop
update_active_functions(0, 0, 0); // Disables all functions
return true;
}
else return false;
}
// Checks for valid message - looking for correct preamble using bitmasks
// returns number of bytes if valid bit-pattern is found. Otherwise -1 is returned.
int8_t verify_dcc_message() {
int8_t number_of_bytes = -1;
uint64_t masked_message_3_bytes = input_bit_buffer & MESSAGE_MASK_3_BYTES;
if (masked_message_3_bytes == MESSAGE_3_BYTES) number_of_bytes = 3;
uint64_t masked_message_4_bytes = input_bit_buffer & MESSAGE_MASK_4_BYTES;
if (masked_message_4_bytes == MESSAGE_4_BYTES) number_of_bytes = 4;
uint64_t masked_message_5_bytes = input_bit_buffer & MESSAGE_MASK_5_BYTES;
if (masked_message_5_bytes == MESSAGE_5_BYTES) number_of_bytes = 5;
return number_of_bytes;
}
//start of transmission -> byte_n(address byte) -> ... -> byte_0(error detection byte) -> end of transmission
void bits_to_byte_array(int8_t number_of_bytes, uint8_t byte_array[]) {
for (uint8_t i = 0; i < number_of_bytes; i++) {
byte_array[i] = input_bit_buffer >> (i * 9 + 1);
}
}
// Sequence of bits gets evaluated
void evaluate_message() {
static bool reset_message_flag;
// Check if input buffer contains a valid dcc message
int8_t number_of_bytes = verify_dcc_message();
// number_of_bytes contains the amount of bytes when the message is valid, otherwise -1
if (number_of_bytes != -1) {
// Split data into 8Bit array
uint8_t byte_array[SIZE_BYTE_ARRAY] = {0};
bits_to_byte_array(number_of_bytes, byte_array);
// Check for errors
if (error_detection(number_of_bytes, byte_array)) {
// Check for matching address
if (address_evaluation(number_of_bytes, byte_array)) {
reset_message_flag = false;
instruction_evaluation(number_of_bytes, byte_array);
}
else if (reset_message_flag) {
// When previous packet was a reset message -> enter program mode
program_mode(number_of_bytes, byte_array);
}
else {
// Check for reset message and set flag when reset message is received
reset_message_flag = reset_message_check(number_of_bytes, byte_array);
}
}
}
}
// DCC-Signal (GPIO 21) rising edge interrupt
void track_signal_rise(unsigned int gpio, long unsigned int events) {
// Save current timer value
rising_edge_time = get_absolute_time();
// Disable rising edge interrupt and enable falling edge interrupt
gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE, false, &track_signal_rise);
gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_FALL, true, &track_signal_fall);
}
// DCC-Signal (GPIO 21) falling edge interrupt
void track_signal_fall(unsigned int gpio, long unsigned int events) {
// Save current timer value
falling_edge_time = get_absolute_time();
// Time difference is equal to the time the signal was in a logical high state
int64_t time_logical_high = absolute_time_diff_us(rising_edge_time, falling_edge_time);
// When logical high was longer than 87us write 0 bit into buffer otherwise 1
bool bit;
if (time_logical_high > 87) bit = 0;
else bit = 1;
input_bit_buffer <<= 1;
input_bit_buffer |= bit;
// evaluate sequence of bits saved in buffer
evaluate_message();
// Disable falling edge interrupt and enable rising edge interrupt
gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_FALL, false, &track_signal_fall);
gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE, true, &track_signal_rise);
}
// Output initialization function - Configures pwm frequency and clock divider according to CV_111 - CV_171
void init_outputs() {
gpio_init_mask(GPIO_ALLOWED_OUTPUTS);
gpio_set_dir_out_masked(GPIO_ALLOWED_OUTPUTS); // Note: This might also disable UART on GPIO0 & GPIO1
uint32_t PWM_enabled_outputs = get_32bit_CV(111) & GPIO_ALLOWED_OUTPUTS;
uint32_t slice, channel;
uint16_t wrap, level;
uint8_t clock_divider;
uint32_t mask = 1;
for (uint8_t i = 0; i < 32; ++i) {
if (PWM_enabled_outputs & mask) {
slice = pwm_gpio_to_slice_num(i);
channel = pwm_gpio_to_channel(i); // Channel A = "0"; Channel B = "1"
wrap = get_16bit_CV(115 + 7 * slice);
level = get_16bit_CV(118 + 7 * slice + 2 * channel);
clock_divider = CV_ARRAY_FLASH[117 + 7 * slice] + 1;
gpio_set_function(i, GPIO_FUNC_PWM);
pwm_set_wrap(slice, wrap);
pwm_set_gpio_level(i, 0);
level_table[i] = level;
pwm_set_clkdiv_int_frac(slice, clock_divider, 0);
pwm_set_enabled(slice, true);
}
mask <<= 1;
}
}
// Measures "base" pwm duty cycle needed to overcome friction
uint16_t measure_base_pwm(bool direction, uint8_t iterations) {
uint gpio;
if (direction) gpio = MOTOR_FWD_PIN;
else gpio = MOTOR_REV_PIN;
float level_arr[iterations];
for (int i = 0; i < iterations; ++i) {
uint16_t max_level = _125M / (CV_ARRAY_FLASH[8] * 100 + 10000);
uint16_t level = max_level / 20;
LOG(3, "iteration %d: maxlevel %d level %d\n", i, max_level, level);
float measurement;
do {
pwm_set_gpio_level(gpio, level);
busy_wait_ms(30);
level += max_level / 500;
measurement = measure(CV_ARRAY_FLASH[60],
CV_ARRAY_FLASH[61],
CV_ARRAY_FLASH[62],
CV_ARRAY_FLASH[63],
direction);
LOG(3, "level %d measurement %f loop-cond: %f\n", level, measurement,
measurement - (float) CV_ARRAY_FLASH[171]);
if (level > max_level) {
// Abort measurement and write default value of 0 to flash
LOG(1, "measure_base_pwm: abort measurement and return 0\n");
return 0;
}
} while ((measurement - (float) CV_ARRAY_FLASH[171]) < 5.0f);
LOG(3, "level_arr[%d] = %f\n", i, level);
level_arr[i] = (float) level;
busy_wait_ms(100);
}
// Find and return overall average discarding outliers in measurement - multiply with 0.9
float retVal = 0.9f * two_std_dev(level_arr, 5);
LOG(1, "measure_base_pwm: %d(%f)\n", (uint16_t) retVal, retVal);
return (uint16_t) (retVal);
}
// Check for flash memory factory condition and adc offset setup
// When factory condition is found the CV_ARRAY_DEFAULT will be written into flash
// When ADC Setup is not configured run adc offset adjustment function and write adc offset into flash
void cv_setup_check() {
// Check for flash factory setting and set CV_FLASH_ARRAY to default values when factory condition ("0xFF") is found.
if (CV_ARRAY_FLASH[64] == 0xFF) {
LOG(1, "found cv[64] equals to 0xff, reseting CVs (and CV[8] = 8)\n");
uint8_t arr[4] = {125, 8, 7, 124};
program_mode(4, arr); //reset to CV_ARRAY_DEFAULT (write CV_8 = 8)
}
// Check for adc offset setup
if (CV_ARRAY_FLASH[171] == 0xFF) {
LOG(1, "found cv[171] equals to 0xff, adc offset adjstments (and cr[7] = 7)\n");
uint8_t arr[4] = {125, 7, 6, 124};
program_mode(4, arr); //ADC offset adjustment (write CV_7 = 7)
}
// Check for base PWM configuration - used for feed-forward
// Forward Direction
if (get_16bit_CV(175) == 0) {
LOG(1, "found cv[175] equals to 0, forward direction\n");
uint16_t base_pwm_fwd = measure_base_pwm(true, 10);
uint8_t base_pwm_fwd_high_byte = base_pwm_fwd >> 8;
uint8_t base_pwm_fwd_low_byte = base_pwm_fwd & 0x00FF;
uint8_t arr0[4] = {125, base_pwm_fwd_high_byte, 175, 124};
program_mode(4, arr0);
uint8_t arr1[4] = {125, base_pwm_fwd_low_byte, 176, 124};
program_mode(4, arr1);
}
// Reverse Direction
if (get_16bit_CV(177) == 0) {
LOG(1, "found cv[177] equals to 0, reverse direction\n");
uint16_t base_pwm_rev = measure_base_pwm(false, 10);
uint8_t base_pwm_rev_high_byte = base_pwm_rev >> 8;
uint8_t base_pwm_rev_low_byte = base_pwm_rev & 0x00FF;
uint8_t arr0[4] = {125, base_pwm_rev_high_byte, 177, 124};
program_mode(4, arr0);
uint8_t arr1[4] = {125, base_pwm_rev_low_byte, 178, 124};
program_mode(4, arr1);
}
LOG(1, "int_lim_max %d\n", CV_ARRAY_FLASH[51]);
LOG(1, "int_lim_min %d\n", CV_ARRAY_FLASH[52]);
}
// Motor PWM initialization
void init_motor_pwm(uint8_t gpio) {
uint16_t wrap_counter = (_125M / (CV_ARRAY_FLASH[8] * 100 + 10000)) - 1;
uint32_t slice_num = pwm_gpio_to_slice_num(gpio);
pwm_set_clkdiv_int_frac(slice_num, CV_ARRAY_FLASH[173], 0);
pwm_set_wrap(slice_num, wrap_counter);
pwm_set_gpio_level(gpio, 0);
pwm_set_enabled(slice_num, true);
LOG(2, "init motor(%d): wrapCounter %d clkdiv %d\n", gpio, wrap_counter, CV_ARRAY_FLASH[173]);
}
// Main initialization - GPIO Config / ADC Config
void init_gpio_adc() {
if (gpio_get_function(MOTOR_FWD_PIN) != 4) {
gpio_set_function(MOTOR_FWD_PIN, GPIO_FUNC_PWM);
gpio_set_function(MOTOR_REV_PIN, GPIO_FUNC_PWM);
adc_init();
adc_gpio_init(FWD_V_EMF_ADC_PIN);
adc_gpio_init(REV_V_EMF_ADC_PIN);
adc_fifo_setup(true, false, 0, false, false);
}
}
int main() {
stdio_init_all();
LOG(1, "\n\n======\ncore0 init\n");
init_gpio_adc();
LOG(1, "init motor pwms\n");
init_motor_pwm(MOTOR_FWD_PIN);
init_motor_pwm(MOTOR_REV_PIN);
LOG(1, "check cvs\n");
cv_setup_check();
LOG(1, "init outputs\n");
init_outputs();
LOG(1, "init gpios\n");
gpio_init(DCC_INPUT_PIN);
gpio_set_dir(DCC_INPUT_PIN, GPIO_IN);
gpio_pull_up(DCC_INPUT_PIN);
gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE, true, &track_signal_rise);
LOG(1, "core0 done\n");
busy_wait_ms(100);
multicore_launch_core1(core1_entry);
while (true);
}