Files
RP2040-Decoder/shared.c
T
gab-k f3ffb73b62 Copy code from flash to ram in order to not use XIP allowing writing to flash memory while both cores are running;
Motor control now operates with two states/modes;
Extended Default CV Range to 1024 - refers to NMRA/RCN standards
2024-01-05 00:37:21 +01:00

71 lines
2.6 KiB
C

//////////////////////////
// RP2040-Decoder //
// Gabriel Koppenstein //
// shared.c //
//////////////////////////
#include "shared.h"
uint8_t speed_step_target = 0;
uint8_t speed_step_target_prev = 0;
// Functions in shared.c can be accessed by both cores
// Measures Back-EMF voltage (proportional to the rotational speed of the motor) on GPIO 28 and GPIO 29 respectively (depending on direction)
float measure(uint8_t total_iterations,
uint8_t measurement_delay_us,
uint8_t l_side_arr_cutoff,
uint8_t r_side_arr_cutoff,
bool direction) {
uint32_t sum = 0;
uint16_t adc_val[total_iterations];
int32_t j = 0;
uint16_t key;
pwm_set_gpio_level(MOTOR_FWD_PIN, 0);
pwm_set_gpio_level(MOTOR_REV_PIN, 0);
adc_select_input((!direction) + 2);
busy_wait_us(measurement_delay_us);
adc_run(true);
for (int32_t i = 0; i < total_iterations; ++i) {
//Take adc value out of fifo when available, then do one step of insertion sort.
adc_val[i] = adc_fifo_get_blocking();
key = adc_val[i];
j = i - 1;
while (j >= 0 && adc_val[j] > key) {
adc_val[j + 1] = adc_val[j];
j--;
}
adc_val[j + 1] = key;
}
adc_run(false);
//discard x entries beginning from the lowest entry of the array (counting up); x = msr.l_side_arr_cutoff
//discard y entries beginning from the highest index of the array (counting down); y = msr.r_side_arr_cutoff
for (int32_t i = l_side_arr_cutoff; i < total_iterations - r_side_arr_cutoff; ++i) {
sum += adc_val[i];
}
float res = (float) sum / (float) (total_iterations - (l_side_arr_cutoff + r_side_arr_cutoff));
// return true to keep the repeating timer active
return res;
}
// retrieve 4Bytes from CV_ARRAY_FLASH at once and return 32-Bit value
uint32_t get_32bit_CV(uint16_t CV_start_index) {
uint8_t byte_3 = CV_ARRAY_FLASH[CV_start_index];
uint8_t byte_2 = CV_ARRAY_FLASH[CV_start_index + 1];
uint8_t byte_1 = CV_ARRAY_FLASH[CV_start_index + 2];
uint8_t byte_0 = CV_ARRAY_FLASH[CV_start_index + 3];
return (byte_0) + (byte_1 << 8) + (byte_2 << 16) + (byte_3 << 24);
}
// retrieve 2Bytes from CV_ARRAY_FLASH at once and return 16-Bit value
uint16_t get_16bit_CV(uint16_t CV_start_index) {
uint8_t byte_1 = CV_ARRAY_FLASH[CV_start_index];
uint8_t byte_0 = CV_ARRAY_FLASH[CV_start_index + 1];
return (byte_0) + (byte_1 << 8);
}
bool get_direction_of_speed_step(uint8_t speed_step) {
// Shift by 7 Bytes to move bit7 into bit0 position and return
return speed_step >> 7;
}