Files
RP2040-Decoder/core0.h
T

188 lines
6.4 KiB
C

/*!
*
* \file core0.h
* Used exclusively by core0
*
*/
#pragma once
#include "shared.h"
#include "CV.h"
#define SIZE_BYTE_ARRAY 5
#define MESSAGE_3_BYTES 0b11111111110000000000000000000000000001
#define MESSAGE_MASK_3_BYTES 0b11111111111000000001000000001000000001
#define MESSAGE_4_BYTES 0b11111111110000000000000000000000000000000000001
#define MESSAGE_MASK_4_BYTES 0b11111111111000000001000000001000000001000000001
#define MESSAGE_5_BYTES 0b11111111110000000000000000000000000000000000000000000001
#define MESSAGE_MASK_5_BYTES 0b11111111111000000001000000001000000001000000001000000001
/*!
* \brief Bitmasks used for clearing bits corresponding to function blocks
*
* [0] = F0-F4
* [1] = F5-F8
* [2] = F9-F12
* [3] = F13-F20
* [4] = F21-F28
* [5] = F29-F31
*
*/
const uint32_t clr_bit_arr[6] = {
0b11111111111111111111111111100000, // Clear Bits 0-4 (F0-F4)
0b11111111111111111111111000011111, // Clear Bits 5-8 (F5-F8)
0b11111111111111111110000111111111, // Clear Bits 9-12 (F9-F12)
0b11111111111000000001111111111111, // Clear Bits 13-20 (F13-F20)
0b11100000000111111111111111111111, // Clear Bits 21-28 (F21-F28)
0b00011111111111111111111111111111, // Clear Bits 29-31 (F29-F31)
};
/*!
* \brief Function returns average of values deviating less than twice the standard deviation from original average.
*
* \param arr input array
* \param length amount of elements in input array
* \return average value of values deviating less than 2*standard_dev.
*/
float two_std_dev(const float arr[], uint32_t length);
/*!
* \brief Measures ADC offset and saves the offset value to flash memory.
* \param n Amount of measurements to be done
*/
void adc_offset_adjustment(uint32_t n);
/*!
* \brief Function for acknowledging a CV write or CV verify instruction
*
* Acknowledgement works by creating a spike in current consumption, normally realized by running the motor in alternating directions.
* This current increase is detected by the command station.
* Refers to NMRA S-9.2.3 Section D and RCN-216 Section 3
*/
void acknowledge();
/*!
* \brief Function for verifying a single bit of a CV
* \param cv_address CV Address
* \param bit_val Value of bit to be verified
* \param bit_pos Position of bit to be verified
*/
void verify_cv_bit(uint16_t cv_address, bool bit_val, uint8_t bit_pos);
/*!
* \brief Function for verifying a CV byte
* \param cv_address CV Address
* \param cv_data Byte to be verified
*/
void verify_cv_byte(uint16_t cv_address, uint8_t cv_data);
/*!
* \brief Function for writing a CV byte
* \param cv_address
* \param cv_data
*/
void write_cv_byte(uint16_t cv_address, uint8_t cv_data);
/*!
* \brief CV Programming mode function
* Used on entering programming mode in order to write CV values to persistent flash memory or verify/read bits/bytes from flash. <br>
* Refers to NMRA Standard 9.2.3 ("Service Mode Programming") or RCN-216<br>
*
* Procedure:
* 1. Checks for valid programming command
* 2. Disables core1 timers
* 3. Resets core1
* 4. Saves interrupts
* 5. Evaluates the type of programming instruction Write byte / Verify byte / Verify bit and runs corresponding function
* 6. Restores interrupts
* 7. Launch core1
*
* \param number_of_bytes Number of bytes in byte_array[]
* \param byte_array Pointer to byte_array[]
*/
void program_mode(uint8_t number_of_bytes, const uint8_t byte_array[]);
/*!
* \brief Set outputs according to function mapping in CV257 to CV512
*
* This function maps the functions and direction to the mapped outputs configured in CV257 to CV512.
* Also enables PWM when enabled according to CV112 to CV115.
*
* \param functions_to_set_bitmask Function bitmask F0 is bit0, F1 is bit1, ...
*/
void set_outputs(uint32_t functions_to_set_bitmask);
void update_active_functions(uint32_t new_function_bitmask, uint8_t clr_bit_ind, bool direction_change);
bool error_detection(int8_t number_of_bytes, const uint8_t *byte_array);
bool is_long_address(uint8_t number_of_bytes, const uint8_t byte_array[]);
bool address_evaluation(uint8_t number_of_bytes, const uint8_t byte_array[]);
void instruction_evaluation(uint8_t number_of_bytes, const uint8_t byte_array[]);
bool reset_message_check(uint8_t number_of_bytes, const uint8_t *const byte_array);
int8_t verify_dcc_message();
void bits_to_byte_array(int8_t number_of_bytes, uint8_t byte_array[]);
void evaluate_message();
/*!
* \brief Track signal rising edge interrupt callback function
*
* Saves timer counter value using get_absolute_time(), then disables rising edge IRQ and enables falling edge IRQ.
* Parameters are unused.
*
* \param gpio Unused parameter
* \param events Unused parameter
*/
void track_signal_rise(unsigned int gpio, long unsigned int events);
/*!
* \brief Track signal falling edge interrupt callback function
*
* Saves timer counter value using get_absolute_time(), then calculates time difference between rising and falling edge.
* When the time difference is greater than 87us, this bit is interpreted as a logical 0.
* Refers to NMRA S-9.1 and RCN-210 standards
* Puts the latest bit value into buffer, then evaluates complete buffer using evaluate_message().
* Parameters are unused.
*
* \param gpio Unused parameter
* \param events Unused parameter
*/
void track_signal_fall(unsigned int gpio, long unsigned int events);
/*!
* \brief Output initialization function
*
* Initializes all allowed GPIO outputs as outputs <br>
* Sets PWM functionality for GPIOs configured as PWM pins CV_112 - CV_115 (see CV.h for reference) <br>
* PWM frequency and clock divider are configured according to CV_116 - CV_171 (see CV.h for reference) <br>
*/
void init_outputs();
/*!
* \brief Checks various CV values in order to detect factory condition or pending calibrations
*
* Procedure:
* 1. Check for flash memory factory condition when found write default values specified in CV.h to flash memory
* 2. Check for existing ADC offset setup when not found write 7 to read-only CV_7 in order to trigger a ADC offset measurement/calibration
* 3. Check for base PWM configuration/calibration, run calibration when none is found
*/
void cv_setup_check();
/*!
* \brief Function initializes motor PWM for pin specified
* \param gpio GPIO pin
*/
void init_motor_pwm(uint8_t gpio);
/*!
* \brief Initializes ADC
*
* Function initializes ADC, corresponding GPIO pins and ADC FIFO
*/
void init_adc();