69 lines
2.8 KiB
C
69 lines
2.8 KiB
C
//////////////////////////
|
|
// RP2040-Decoder //
|
|
// Gabriel Koppenstein //
|
|
// shared.h //
|
|
//////////////////////////
|
|
|
|
#pragma once
|
|
#include "string.h"
|
|
#include "pico/float.h"
|
|
#include "pico/stdlib.h"
|
|
#include "pico/multicore.h"
|
|
#include "pico/printf.h"
|
|
#include "hardware/pwm.h"
|
|
#include "hardware/adc.h"
|
|
#include "hardware/flash.h"
|
|
#include "hardware/irq.h"
|
|
|
|
|
|
// here you can enable printf debugging (needs extra soldering and you have to enable uart in the cmake configuration)
|
|
// please note
|
|
// - if it's disabled it will be compiled completely out
|
|
// - be careful that printf debugging can change your timing behavior, for example in the pid controller limit the outputs
|
|
// like already done (only print every 100th iteration for example!)
|
|
// - also note that with logging enabled GPIO0/1 are DISABLED from decoder functions because they are used for uart to the
|
|
// outside world (this is configure automatically for you below!)
|
|
// - IMPORTANT: you have to enable uart in the cmakelists.txt to enable logging!
|
|
#define LOGLEVEL 0
|
|
#define LOG(level, ...) { if(level <= LOGLEVEL) {printf(__VA_ARGS__);}}
|
|
|
|
// Constant Value of 125 x 10⁶
|
|
#define _125M 125000000
|
|
|
|
// GPIO used for DCC-Signal, Motor PWM or ADC
|
|
#define DCC_INPUT_PIN 21u
|
|
#define MOTOR_FWD_PIN 23u
|
|
#define MOTOR_REV_PIN 22u
|
|
#define FWD_V_EMF_ADC_PIN 28u
|
|
#define REV_V_EMF_ADC_PIN 29u
|
|
|
|
// if logging is enabled do NOT use gpio0/1 for functions in the decoder
|
|
#if LOGLEVEL != 0
|
|
// GPIO used directly (GPIO 2-5 incl.) as outputs or to switch auxiliary output transistors (GPIO 24-27 incl.)
|
|
#define GPIO_OUTPUT_PIN_MASK (1u<<24) | (1u<<25) | (1u<<26) | (1u<<27) | (1u<<5) | (1u<<4) | (1u<<3) | (1u<<2)
|
|
#else
|
|
// GPIO used directly (GPIO 0-5 incl.) as outputs or to switch auxiliary output transistors (GPIO 24-27 incl.)
|
|
#define GPIO_OUTPUT_PIN_MASK (1u<<24) | (1u<<25) | (1u<<26) | (1u<<27) | (1u<<5) | (1u<<4) | (1u<<3) | (1u<<2) | (1u<<1) | (1u<<0)
|
|
#endif
|
|
|
|
// GPIO pin mask to prevent setting illegal GPIOs (ADC, Motor, DCC Input Pin)
|
|
#define GPIO_ILLEGAL_MASK (1u<<DCC_INPUT_PIN) | (1u<<MOTOR_FWD_PIN) | (1u<<MOTOR_REV_PIN) | (1u<<FWD_V_EMF_ADC_PIN) | (1u<<REV_V_EMF_ADC_PIN)
|
|
|
|
// GPIO pin mask with allowed outputs (AUX & GPIO (configured as outputs))
|
|
#define GPIO_ALLOWED_OUTPUTS (GPIO_OUTPUT_PIN_MASK) & ~(GPIO_ILLEGAL_MASK)
|
|
|
|
// Offset from base address used for saving CV_ARRAY_FLASH
|
|
#define FLASH_TARGET_OFFSET (PICO_FLASH_SIZE_BYTES-FLASH_SECTOR_SIZE)
|
|
|
|
extern repeating_timer_t pid_control_timer;
|
|
extern repeating_timer_t speed_helper_timer;
|
|
extern const uint8_t *CV_ARRAY_FLASH;
|
|
void core1_entry();
|
|
float measure(uint8_t total_iterations,
|
|
uint8_t measurement_delay_us,
|
|
uint8_t l_side_arr_cutoff,
|
|
uint8_t r_side_arr_cutoff,
|
|
bool direction);
|
|
uint32_t get_32bit_CV (uint16_t CV_start_index);
|
|
uint16_t get_16bit_CV (uint16_t CV_start_index);
|