Files
RP2040-Decoder/core1.c
T
1nct ad570fba35 - remove m_pwm_offset_adjustment;
- offset now adjusted in pid_control loop;
- pid sampling time depends on speed step;
- speed table implemented & and init function;
2022-03-12 10:23:51 +01:00

231 lines
8.5 KiB
C

//////////////////////////
// RP2040-Decoder //
// Gabriel Koppenstein //
// core1.c //
//////////////////////////
#include "core1.h"
uint32_t latest_target = 0;
uint8_t latest_target_index = 0;
uint16_t speed_table[127] = {0};
struct repeating_timer pid_control_timer,speed_helper_timer;
typedef struct pid_params{
int32_t k_p;
int32_t k_i;
int32_t k_d;
int32_t t_s;
int32_t sum_limit_max;
int32_t sum_limit_min;
int32_t output;
int32_t e;
int32_t e_prev;
int32_t e_sum;
int32_t offset;
int32_t offset_base;
uint16_t max_output;
bool direction_prev;
}pid_params;
pid_params pid;
typedef struct measure_params{
uint32_t val;
uint8_t delay_in_us;
uint8_t total_iterations;
uint8_t left_side_array_cutoff;
uint8_t right_side_array_cutoff;
uint8_t adc_offset;
}measure_params;
measure_params msr;
uint16_t calc_end_target(){
//Forward
if(target_direction){
if (target_speed_step == 128) return 0;
else return (target_speed_step-129);
}
//Reverse
else {
if (target_speed_step == 0) return 0;
else return (target_speed_step-1);
}
}
bool speed_helper() {
uint8_t accel_rate = CV_ARRAY_FLASH[2];
uint8_t decel_rate = CV_ARRAY_FLASH[3];
uint16_t end_target_index = calc_end_target();
static uint8_t speed_helper_counter;
//latest_target only gets adjusted when the counter equals the acc/dec rate
//-> Time for 1 Speed Step := (speed_helper timer delay)*(accel_rate)
//Emergency Stop
if (target_speed_step == 129 || target_speed_step==1) {
latest_target_index = 0;
speed_helper_counter = 0;
latest_target = speed_table[latest_target_index];
}
//Acceleration
else if (end_target_index > latest_target_index && speed_helper_counter == accel_rate) {
if(!accel_rate) latest_target_index = end_target_index; // directly accelerate to end target speed
else latest_target_index++;
latest_target = speed_table[latest_target_index];
speed_helper_counter = 0;
}
//Deceleration
else if (end_target_index < latest_target_index && speed_helper_counter == decel_rate) {
if(!decel_rate) latest_target_index = end_target_index; // directly decelerate to end target speed
else latest_target_index--;
latest_target = speed_table[latest_target_index];
speed_helper_counter = 0;
}
//Acceleration/Deceleration "scheduled"
else if (end_target_index != latest_target_index) speed_helper_counter++;
//Target reached -> Reset Counter
else speed_helper_counter = 0;
return true;
}
uint32_t measure(bool direction){
uint32_t sum = 0;
uint16_t adc_val[100 /*msr.total_iterations*/];
int32_t j = 0;
uint16_t key;
pwm_set_gpio_level(MOTOR_FWD_PIN, 0);
pwm_set_gpio_level(MOTOR_REV_PIN, 0);
adc_select_input(!direction);
busy_wait_us(msr.delay_in_us);
adc_run(true);
for (int32_t i = 0; i < msr.total_iterations; ++i) {
//Take adc value out of fifo when available, then do one step of insertion sort.
adc_val[i] = adc_fifo_get_blocking();
key = adc_val[i];
j = i - 1;
while (j >= 0 && adc_val[j] > key) {
adc_val[j + 1] = adc_val[j];
j--;
}
adc_val[j + 1] = key;
}
adc_run(false);
//discard x entries beginning from the lowest entry of the array (counting up); x = msr.left_side_array_cutoff
//discard y entries beginning from the highest index of the array (counting down); y = msr.right_side_array_cutoff
for (int32_t i = msr.left_side_array_cutoff; i < msr.total_iterations - msr.right_side_array_cutoff ; ++i) {
sum += adc_val[i];
}
uint32_t res = sum / ( msr.total_iterations - (msr.left_side_array_cutoff+msr.right_side_array_cutoff) );
return res;
}
void adjust_pwm_level(uint16_t level) {
if (target_direction) {
pwm_set_gpio_level(MOTOR_REV_PIN, 0);
pwm_set_gpio_level(MOTOR_FWD_PIN, level);
}
//Reverse
else {
pwm_set_gpio_level(MOTOR_FWD_PIN, 0);
pwm_set_gpio_level(MOTOR_REV_PIN, level);
}
}
bool pid_control(struct repeating_timer *t){
if(target_direction != pid.direction_prev || !latest_target) {
pid.e_sum = 0;
pid.offset = pid.offset_base;
}
msr.val = measure(target_direction);
pid.e = (int32_t)latest_target - (int32_t)msr.val + msr.adc_offset;
if (pid.e_sum > pid.sum_limit_max) pid.e_sum = pid.sum_limit_max;
else if (pid.e_sum < pid.sum_limit_min) pid.e_sum = pid.sum_limit_min;
pid.output = ( pid.k_p*pid.e + pid.k_i*pid.t_s*pid.e_sum + ( pid.k_d*(pid.e-pid.e_prev) / pid.t_s ) ) / 1000;
pid.output += pid.offset;
if (latest_target_index < 5){
pid.output += 20*pid.e; //"compensate" friction
pid.offset_base = pid.offset; //"baseline" pwm offset level
}
if (pid.output < 0 || !latest_target) pid.output = 0;
else if (pid.output > pid.max_output) pid.output = pid.max_output;
adjust_pwm_level(pid.output);
adc_fifo_drain();
pid.direction_prev = target_direction;
pid.e_sum += pid.e;
pid.e_prev = pid.e;
// Adjust offset when the absolute value of e_sum is half of max
if (pid.e_sum > pid.sum_limit_max/2 || pid.e_sum < pid.sum_limit_min/2){
pid.offset += 3*(pid.e_sum/pid.sum_limit_max);
}
if (pid.offset > 5000) pid.offset = 5000;
else if (pid.offset < 1) pid.offset = 1;
// Increase sampling time for higher speed steps - Decrease for lower speed steps
pid_control_timer.delay_us = (8000*latest_target_index)/126 + 2000;
pid.t_s = ((8000*latest_target_index)/126 + 2000)/1000;
printf("%d\n",pid.output);
return true;
//printf("off:%d\n",pid.offset);
}
void init_speed_table(){
double v_min = (double)CV_ARRAY_FLASH[1];
double v_mid = (double)CV_ARRAY_FLASH[5]*16;
double v_max = (double)CV_ARRAY_FLASH[4]*16;
double m_1 = (v_mid-v_min)/62;
double m_2 = (v_max-v_mid)/63;
for (uint8_t i = 1; i < 63; ++i) {
speed_table[i] = (uint16_t)lround(m_1*(i-1)+v_min);
}
for (uint8_t i = 63; i < 127; ++i) {
speed_table[i] = (uint16_t)lround(m_2*(i-63)+v_mid);
}
}
void init_pid(){
pid.k_p = 2000;
pid.k_i = 50;
pid.k_d = 1000;
pid.t_s = CV_ARRAY_FLASH[46]; // Default: (CV_ARRAY_FLASH[46]) = 2
pid.offset = 2500;
pid.sum_limit_max = 1000; /*(float)(CV_ARRAY_FLASH[51] );*/
pid.sum_limit_min = -1000; /*(float)(CV_ARRAY_FLASH[52] * (-1));*/
pid.direction_prev = target_direction;
pid.max_output = _125M/(CV_ARRAY_FLASH[8]*100+10000);
}
void init_msr(){
msr.total_iterations = 100;/*CV_ARRAY_FLASH[60];*/
msr.delay_in_us = 100; /*CV_ARRAY_FLASH[61];*/
msr.left_side_array_cutoff = 15;/*CV_ARRAY_FLASH[62];*/
msr.right_side_array_cutoff = 15;/*CV_ARRAY_FLASH[63];*/
msr.adc_offset = CV_ARRAY_FLASH[171];
}
void init_motor_pwm(uint8_t gpio) {
uint16_t wrap_counter = _125M/(CV_ARRAY_FLASH[8]*100+10000); // 125MHz / f_pwm
uint32_t slice_num = pwm_gpio_to_slice_num(gpio);
pwm_set_clkdiv_int_frac(slice_num,CV_ARRAY_FLASH[173],0);
pwm_set_wrap(slice_num, wrap_counter);
pwm_set_gpio_level(gpio,0);
pwm_set_enabled(slice_num, true);
}
void core1_entry() {
printf("core1 init...\n");
if(gpio_get_function(MOTOR_FWD_PIN) != 4){
gpio_set_function(MOTOR_FWD_PIN, GPIO_FUNC_PWM);
gpio_set_function(MOTOR_REV_PIN, GPIO_FUNC_PWM);
adc_init();
adc_gpio_init(FWD_V_EMF_ADC_PIN);
adc_gpio_init(REV_V_EMF_ADC_PIN);
adc_fifo_setup(true,false,0,false,false);
init_motor_pwm(MOTOR_FWD_PIN);
init_motor_pwm(MOTOR_REV_PIN);
}
init_speed_table();
init_msr();
init_pid();
alarm_pool_add_repeating_timer_ms(alarm_pool_create(0,1),
CV_ARRAY_FLASH[47],
pid_control,
NULL,
&pid_control_timer);
irq_set_priority(0,0x00); // 0x00 = highest priority
alarm_pool_add_repeating_timer_ms(alarm_pool_create(1,1),
CV_ARRAY_FLASH[58],
speed_helper,
NULL,
&speed_helper_timer);
multicore_fifo_push_blocking(20); //send some data to let core0 know that core1 is done
while (1);
}