////////////////////////// // RP2040-Decoder // // Gabriel Koppenstein // // core1.c // ////////////////////////// #include "core1.h" struct repeating_timer pid_control_timer,speed_helper_timer; // Update speed_step_target, end_target_index and direction on receiving data from core0 void update_speed_dir(pid_params *pid, uint32_t speed_step_target){ pid->speed_step_target = speed_step_target; // When CV_29 Bit 0 is set direction is reversed bool reverse_dir = CV_ARRAY_FLASH[28] & 0b00000001; // Forward if(speed_step_target > 127) { pid->direction = true^reverse_dir; if (pid->speed_step_target == 128) pid->end_target_index = 0; else pid->end_target_index = (pid->speed_step_target-129); } // Reverse else { pid->direction = false^reverse_dir; if (pid->speed_step_target == 0) pid->end_target_index = 0; else pid->end_target_index = (pid->speed_step_target-1); } } // This function gets called every x milliseconds where x is CV_175. // The purpose of this function is to implement a time delay in acceleration or deceleration bool speed_helper(struct repeating_timer *t) { // pid->setpoint only gets adjusted when the speed_helper_counter is equal to the accel_rate/decel_rate // -> Time for 1 Speed Step := (speed_helper timer delay)*(accel_rate) or CV_175*CV_3 or CV_175*CV_4 pid_params *pid = (pid_params *)(t->user_data); uint8_t accel_rate = CV_ARRAY_FLASH[2]; uint8_t decel_rate = CV_ARRAY_FLASH[3]; static uint8_t speed_helper_counter; static uint8_t speed_table_index; // Emergency Stop if (pid->speed_step_target == 129 || pid->speed_step_target==1) { speed_table_index = 0; speed_helper_counter = 0; pid->setpoint = pid->speed_table[speed_table_index]; } // Acceleration else if (pid->end_target_index > speed_table_index && speed_helper_counter == accel_rate) { if(!accel_rate) speed_table_index = pid->end_target_index; // directly accelerate to end target speed else speed_table_index++; pid->setpoint = pid->speed_table[speed_table_index]; speed_helper_counter = 0; } // Deceleration else if (pid->end_target_index < speed_table_index && speed_helper_counter == decel_rate) { if(!decel_rate) speed_table_index = pid->end_target_index; // directly decelerate to end target speed else speed_table_index--; pid->setpoint = pid->speed_table[speed_table_index]; speed_helper_counter = 0; } // Acceleration/Deceleration "scheduled" else if (pid->end_target_index != speed_table_index) speed_helper_counter++; // Target reached -> Reset Counter else speed_helper_counter = 0; // return true to schedule the repeating timer again return true; } // Helper function to adjust pwm level/duty cycle. void adjust_pwm_level(uint16_t level, pid_params *pid) { if (pid->direction) { pwm_set_gpio_level(MOTOR_REV_PIN, 0); pwm_set_gpio_level(MOTOR_FWD_PIN, level); } //Reverse else { pwm_set_gpio_level(MOTOR_FWD_PIN, 0); pwm_set_gpio_level(MOTOR_REV_PIN, level); } } // Update feed-forward slope/gradient for both directions void update_m(pid_params *pid){ pid->m_fwd = (pid->y_2_fwd-pid->y_1_fwd)/(pid->x_2_fwd-pid->x_1_fwd); pid->m_rev = (pid->y_2_rev-pid->y_1_rev)/(pid->x_2_rev-pid->x_1_rev); } // Update feedforward function value y_2 in both directions void update_y(pid_params *pid,float i){ // Forward if(pid->direction) { pid->y_2_fwd += i*pid->k_ff; // Limit y_2_fwd if(pid->y_2_fwd > pid->max_output) pid->y_2_fwd = pid->max_output; else if(pid->y_2_fwd < pid->y_1_fwd) pid->y_2_fwd = pid->y_1_fwd; } // Reverse else{ pid->y_2_rev += i*pid->k_ff; // Limit y_2_rev if(pid->y_2_rev > pid->max_output) pid->y_2_rev = pid->max_output; else if(pid->y_2_rev < pid->y_1_rev) pid->y_2_rev = pid->y_1_rev; } update_m(pid); } // Returns feedforward value corresponding to current setpoint float get_ff_val(pid_params *pid){ float val; // Forward if(pid->direction){ val = pid->m_fwd*((float)pid->setpoint-pid->x_1_fwd)+pid->y_1_fwd; } // Reverse else{ val = pid->m_rev*((float)pid->setpoint-pid->x_1_rev)+pid->y_1_rev; } return val; } // Returns proportional gain value corresponding to current setpoint float get_kp(pid_params *pid){ float sp = (float)pid->setpoint; if (sp < pid->k_p_x_1){ return pid->k_p_m_1 * sp + pid->k_p_y_0; } else{ return pid->k_p_m_2 * (sp - pid->k_p_x_1) + pid->k_p_y_1; } } // PID controller function gets called every x milliseconds where x is CV_49 aka sampling time (pid->t) bool pid_control(struct repeating_timer *t){ // Cast (void *) to (pid_params *) pid_params *pid = (pid_params *)(t->user_data); // Acceleration from standstill or change in direction -> reset previous derivative, error and integral parts if((!pid->setpoint_prev && !pid->setpoint) || (pid->direction != pid->direction_prev)){ pid->d_prev = 0.0f; pid->i_prev = 0.0f; pid->e_prev = 0.0f; } // Get feed-forward and proportional gain values float feed_fwd = get_ff_val(pid); pid->k_p = get_kp(pid); // Measure BEMF voltage and compute error pid->measurement = measure(pid->msr_total_iterations, pid->msr_total_iterations, pid->l_side_arr_cutoff, pid->r_side_arr_cutoff, pid->direction); float e = (float)pid->setpoint - (pid->measurement - pid->adc_offset); // Proportional part, integral part and derivative part (including digital low-pass-filter with time constant tau) float p = pid->k_p * e; float i = pid->ci_0*(e + pid->e_prev) + pid->i_prev; float d = pid->cd_0*(pid->measurement-pid->measurement_prev)+pid->cd_1*pid->d_prev; // Check for limits on the integral part if (i > pid->int_lim_max)i = pid->int_lim_max; else if (i < pid->int_lim_min)i = pid->int_lim_min; // Sum feed forward + all controller terms (p+i+d). Limit Output from 0% to 100% duty cycle float output = feed_fwd+p+i+d; if (output < 0 || !pid->setpoint) output = 0.0f; else if (output > pid->max_output) output = pid->max_output; // Set PWM Level and discard results in adc fifo adjust_pwm_level((uint16_t)roundf(output),pid); adc_fifo_drain(); if(pid->setpoint > 2) { printf("p:%f\n", p); printf("i:%f\n", i); printf("d:%f\n", d); printf("o:%f\n", output); } // Check for High or Low Integrator values -> Update x,y values of feedforward function if( (output < pid->max_output && output > pid->max_output/2) && ((i > pid->int_lim_max/2) || (i < pid->int_lim_min/2)) ) update_y(pid,i); // Save previous error, integrator, differentiator, direction, setpoint and measured value also sum error to e_sum pid->e_prev = e; pid->i_prev = i; pid->d_prev = d; pid->direction_prev = pid->direction; pid->setpoint_prev = pid->setpoint; pid->measurement_prev = pid->measurement; // return true to schedule the repeating timer again return true; } // PID controller and measurement parameter, and speed_table initialization void init_pid(pid_params *pid){ // Measurement variables initialization pid->adc_offset = (float)CV_ARRAY_FLASH[171]; pid->msr_total_iterations = CV_ARRAY_FLASH[60]; pid->msr_delay_in_us = CV_ARRAY_FLASH[61]; pid->l_side_arr_cutoff = CV_ARRAY_FLASH[62]; pid->r_side_arr_cutoff = CV_ARRAY_FLASH[63]; // Speed table initialization // Calculate speed setpoint table according to V_min, V_max and V_mid CVs double v_min = (double)CV_ARRAY_FLASH[1]; double v_mid = (double)CV_ARRAY_FLASH[5]*16; double v_max = (double)CV_ARRAY_FLASH[4]*16; double m_1 = (v_mid-v_min)/62; double m_2 = (v_max-v_mid)/63; pid->speed_table[0] = 0; for (uint8_t i = 1; i < 63; ++i) { pid->speed_table[i] = (uint16_t)lround(m_1*(i-1)+v_min); } for (uint8_t i = 63; i < 127; ++i) { pid->speed_table[i] = (uint16_t)lround(m_2*(i-63)+v_mid); } // Controller constants initialization pid->k_i = (float)CV_ARRAY_FLASH[49]/10; pid->k_d = (float)CV_ARRAY_FLASH[50]/10000; pid->tau = (float)CV_ARRAY_FLASH[47]/1000; pid->t = (float)CV_ARRAY_FLASH[48]/1000; pid->ci_0 = (pid->k_i*pid->t)/2; pid->cd_0 = -(2*pid->k_d)/(2*pid->tau+pid->t); pid->cd_1 = (2*pid->tau-pid->t)/(2*pid->tau+pid->t); pid->int_lim_max = 10*(float)CV_ARRAY_FLASH[51]; pid->int_lim_min = -10*(float)CV_ARRAY_FLASH[52]; pid->k_ff = (float)CV_ARRAY_FLASH[46]/10000; // 0.005f; pid->max_output = (float)(_125M/(CV_ARRAY_FLASH[8]*100+10000)); pid->x_1_rev = 0.0f; pid->x_1_fwd = 0.0f; pid->y_1_fwd = (float)get_16bit_CV(175); //(float)measure_base_pwm(pid,1); pid->y_1_rev = (float)get_16bit_CV(177); //(float)measure_base_pwm(pid,0); pid->x_2_rev = (float)pid->speed_table[126]; pid->x_2_fwd = (float)pid->speed_table[126]; // Controller variables initialization pid->y_2_fwd = pid->max_output; pid->y_2_rev = pid->max_output; pid->measurement = 0.0f; pid->measurement_prev = 0.0f; pid->e_prev = 0.0f; pid->i_prev = 0.0f; pid->d_prev = 0.0f; pid->direction = false; pid->direction_prev = false; pid->speed_step_target = 0; pid->setpoint = 0; // Gain scheduling initialization pid->k_p_x_1_shift = (float)CV_ARRAY_FLASH[59] / 255.0f; pid->k_p_x_1 = (float)pid->speed_table[126] * pid->k_p_x_1_shift; pid->k_p_x_2 = (float)pid->speed_table[126] * (1.0f - pid->k_p_x_1_shift); pid->k_p_y_0 = (float)get_16bit_CV(53) / 100.0f; pid->k_p_y_1 = (float)get_16bit_CV(55) / 100.0f; pid->k_p_y_2 = (float)get_16bit_CV(57) / 100.0f; pid->k_p_m_1 = (pid->k_p_y_1 - pid->k_p_y_0) / pid->k_p_x_1; pid->k_p_m_2 = (pid->k_p_y_2 - pid->k_p_y_1) / pid->k_p_x_2; update_m(pid); } void core1_entry() { printf("core1 init...\n"); pid_params pid_parameters; pid_params *pid = &pid_parameters; init_pid(pid); alarm_pool_add_repeating_timer_ms(alarm_pool_create(0,1), CV_ARRAY_FLASH[48], pid_control, pid, &pid_control_timer); irq_set_priority(0,0x00); // 0x00 = highest priority alarm_pool_add_repeating_timer_ms(alarm_pool_create(1,1), CV_ARRAY_FLASH[174], speed_helper, pid, &speed_helper_timer); // Send direction pointer for access and to let core0 know that core1 is done with initialization, // Note: Pointer will be cast into uint32_t and then back into bool * on core0 (Both 32-Bit Datatype). // This is done only to accommodate the correct data type associated with multicore_fifo_push_blocking(). multicore_fifo_push_blocking((uint32_t) &(pid->direction)); uint64_t packet_timeout_threshold_in_us = CV_ARRAY_FLASH[10]*1000000; absolute_time_t time_last_update = get_absolute_time(); printf("core1 done\n"); while (1){ // Check for time difference between last packet and current time (Packet Timeout) absolute_time_t current_time = get_absolute_time(); if (absolute_time_diff_us(time_last_update,current_time) > packet_timeout_threshold_in_us){ update_speed_dir(pid,0); } // If core0 sends new speed data to core1 speed_step_target and direction variables get updated if(multicore_fifo_rvalid()) { update_speed_dir(pid, multicore_fifo_pop_blocking()); time_last_update = get_absolute_time(); } } }