Hardware Description ==================== Overview -------- .. image:: https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/Block_Diagram.svg :alt: Block Diagram The above block diagram gives a general overview regarding the operation of components. For better illustration it has been divided into four functional blocks. Furthermore, these functional blocks can be subdivided and will be explained below. * **Input Stage** - DCC Signal Level Shift - Bridge Rectifier & Voltage Regulator * **Motor Driver** - Motor Driver - Back EMF measurement (ADC) * **General Purpose** - GPIO - Auxiliary output * **Microcontroller** - Flash memory - Crystal oscillator Characteristics --------------- .. table:: Characteristics table :widths: auto ===================================================== ============================= ========= ========= ===== Parameter Symbol Minimum Maximum Unit ===================================================== ============================= ========= ========= ===== Absolute max. DCC Input Voltage V\ :sub:`DCC`\ -25 +25 V Absolute max. GPIO Voltage\ :sup:`(0)`\ V\ :sub:`PIN`\ -0.5 3.3+0.5 V Input Voltage High\ :sup:`(0)`\ V\ :sub:`IH`\ 2.145 3.6 V Input Voltage Low\ :sup:`(0)`\ V\ :sub:`IL`\ 0 1.155 V Total GPIO Current\ :sup:`(0)`\ I\ :sub:`IOVDD`\ 50 mA Absolute max. motor output current\ :sup:`(1)`\ I\ :sub:`MOTOR`\ 2.8 A Absolute max. auxiliary output current \ :sup:`(2)`\ I\ :sub:`AUX`\ 400 mA ===================================================== ============================= ========= ========= ===== (0): According to: `RP2040 Datasheet `_ (assuming V\ :sub:`DD`\ = 3.3V) (1): According to: `BDR6133 Datasheet `_ (2): According to: `T2N7002BK Datasheet `_ Input Stage ----------- .. image:: https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/Input_Stage.svg :alt: Input Stage D1 Rectifies the DCC square-wave into +V, the amplitude is not critical as long as it's within the 25V limit. The rectified voltage +V is then provided to the 3.3V voltage regulator (U1) and to the motor driver (U2). The MOSFET on the right effectively translates the rather high DCC voltage to a suitable level for the microcontroller to process. When Q1 is turned off GPIO21 is pulled high by the RP2040 internal pull-up resistor, as soon as Q1 gets turned on (VGS > VGS,th), GPIO21 gets pulled to GND potential. R1 and R2 ensure that VGS doesn't exceed ±20V. Motor Driver ------------ .. image:: https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/Motor_Driver.svg :alt: Motor Driver The Motor Driver is a complete H-Bridge IC specifically made for DC-Motors. In order to control the motor, it is necessary to measure the back-EMF. This is done by the ADC, which measures at Points ADC_EMF_A and ADC_EMF_B respectively. The two resistors are used as a voltage divider. Auxiliary Output ---------------- .. image:: https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/Aux_Outputs.svg :alt: Auxiliary Output Switching of loads up to a maximum of about ~400mA can be done using four N-Channel MOSFETs. They are switching on the low-side, which means the load effectively gets connected to GND potential as the transistor starts to conduct. GPIO24 - GPIO27 are used. GPIO ----- To switch lighter loads, six soldering pads on the back side of the PCB are connected to GPIO0 - GPIO5 pins. Although not implemented yet, they could theoretically be used as inputs as well (e.g., Reed switch). Microcontroller --------------- .. image:: https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/Microcontroller.svg :alt: Microcontroller The Microcontroller needs a crystal oscillator to function properly. External flash memory is also needed as it holds the configuration variables and the program itself. R3 & C14 are used to filter ADC_AVDD (ADC Reference Voltage). Complete Schematic ------------------ .. image:: https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/RP2040-Decoder.svg :alt: Complete Schematic BOM & Alternative Parts ------------------------ .. table:: BOM :widths: auto ===================================================== ============================= ==================================== ============================= ===================== ========================= Ref Quantity Value Component Type Component Name Footprint ===================================================== ============================= ==================================== ============================= ===================== ========================= C1, C2, C5, C6, C14 5 10u Ceramic Capacitor / 0603_1608Metric C3, C4, C7, C8, C9, C10, C11, C12, C13, C15 10 100n Ceramic Capacitor / 0603_1608Metric C16, C17 2 33p Ceramic Capacitor / 0603_1608Metric D1 1 V\ :sub:`RMS`\=40V, I\ :sub:`F`\=2A Bridge Rectifier KMB24F MBS (TO-269AA) Q1, Q2, Q3, Q4, Q5 5 V\ :sub:`DS`\=60V, I\ :sub:`D`\=0.4A N-Channel MOSFET T2N7002BK SOT-23 R1, R2, R5, R6 4 6k8 Resistor / 0603_1608Metric R3 1 200 Resistor / 0603_1608Metric R7, R8, R9 3 1k Resistor / 0603_1608Metric U1 1 V\ :sub:`OUT`\=3.3V Low Dropout Voltage Regulator HT7533S SOT-23 U2 1 I=2.8A H-Bridge Driver BDR6133 SOIC-8 U3 1 64Mb Flash Memory W25Q64JVSSIQ SOIC-8 U4 1 / Microcontroller RP2040 QFN-56-1EP_7x7mm_P0.4mm Y1 1 f=12MHz Crystal Oscillator X322512MSB4SI Crystal_SMD_3225-4Pin_3.2x2.5mm ===================================================== ============================= ==================================== ============================= ===================== ========================= NOTE: Keep capacitor V\ :sub:`max`\ in mind! Alternatives for BDR6133: -------------------------- * `PT5126A-S-TP `_ * `PT2476 `_ Alternative for HT7533S: ------------------------ * `GS7533-33TR3 `_