|
|
#define | SIZE_BYTE_ARRAY 5 |
| |
|
#define | MESSAGE_3_BYTES 0b11111111110000000000000000000000000001 |
| |
|
#define | MESSAGE_MASK_3_BYTES 0b11111111111000000001000000001000000001 |
| |
|
#define | MESSAGE_4_BYTES 0b11111111110000000000000000000000000000000000001 |
| |
|
#define | MESSAGE_MASK_4_BYTES 0b11111111111000000001000000001000000001000000001 |
| |
|
#define | MESSAGE_5_BYTES 0b11111111110000000000000000000000000000000000000000000001 |
| |
|
#define | MESSAGE_MASK_5_BYTES 0b11111111111000000001000000001000000001000000001000000001 |
| |
|
#define | ProgramInstrVerifyBit 0b10 |
| |
|
#define | ProgramInstrVerifyByte 0b01 |
| |
|
#define | ProgramInstrWriteByte 0b11 |
| |
| #define | ProgramCmd(instr, adrmsbits) |
| |
|
|
float | two_std_dev (const float arr[], uint32_t length) |
| |
|
void | adc_offset_adjustment (uint32_t length) |
| |
|
void | acknowledge () |
| |
|
void | verify_cv_bit (uint16_t cv_address, bool bit_val, uint8_t bit_pos) |
| |
|
void | verify_cv_byte (uint16_t cv_address, uint8_t cv_data) |
| |
|
void | regular_cv_write (uint16_t cv_index, uint8_t cv_data) |
| |
| void | program_mode (uint8_t number_of_bytes, const uint8_t byte_array[]) |
| | CV Programming mode function Used on entering programming mode in order to write CV values to persistent flash memory or verify/read bits/bytes from flash.
Refers to NMRA Standard 9.2.3 ("Service Mode Programming") or RCN-216
|
| |
|
void | set_outputs (uint32_t functions_to_set_bitmask) |
| |
|
void | update_active_functions (uint32_t new_function_bitmask, uint8_t clr_bit_ind, bool direction_change) |
| |
|
bool | error_detection (int8_t number_of_bytes, const uint8_t *byte_array) |
| |
|
bool | is_long_address (uint8_t number_of_bytes, const uint8_t byte_array[]) |
| |
|
bool | address_evaluation (uint8_t number_of_bytes, const uint8_t byte_array[]) |
| |
|
void | instruction_evaluation (uint8_t number_of_bytes, const uint8_t byte_array[]) |
| |
|
bool | reset_message_check (uint8_t number_of_bytes, const uint8_t *const byte_array) |
| |
|
int8_t | verify_dcc_message () |
| |
|
void | bits_to_byte_array (int8_t number_of_bytes, uint8_t byte_array[]) |
| |
|
void | evaluate_message () |
| |
|
void | track_signal_rise (unsigned int gpio, long unsigned int events) |
| |
|
void | track_signal_fall (unsigned int gpio, long unsigned int events) |
| |
| void | init_outputs () |
| | Output initialization function.
|
| |
| uint16_t | measure_base_pwm (bool direction, uint8_t iterations) |
| | Measures base pwm duty cycles at which the motor barely starts moving.
|
| |
| void | cv_setup_check () |
| | Checks various CV values in order to detect factory condition or pending calibrations.
|
| |
| void | init_motor_pwm (uint8_t gpio) |
| | Function initializes motor PWM for pin specified.
|
| |
| void | init_adc () |
| | Initializes ADC.
|
| |
Used exclusively by core0