/*! * * \file core0.h * Used exclusively by core0 * */ #pragma once #include "shared.h" #include "CV.h" #define SIZE_BYTE_ARRAY 5 #define MESSAGE_3_BYTES 0b11111111110000000000000000000000000001 #define MESSAGE_MASK_3_BYTES 0b11111111111000000001000000001000000001 #define MESSAGE_4_BYTES 0b11111111110000000000000000000000000000000000001 #define MESSAGE_MASK_4_BYTES 0b11111111111000000001000000001000000001000000001 #define MESSAGE_5_BYTES 0b11111111110000000000000000000000000000000000000000000001 #define MESSAGE_MASK_5_BYTES 0b11111111111000000001000000001000000001000000001000000001 const uint32_t clr_bit_arr[6] = { 0b11111111111111111111111111100000, // Clear Bits 0-4 (F0-F4) 0b11111111111111111111111000011111, // Clear Bits 5-8 (F5-F8) 0b11111111111111111110000111111111, // Clear Bits 9-12 (F9-F12) 0b11111111111000000001111111111111, // Clear Bits 13-20 (F13-F20) 0b11100000000111111111111111111111, // Clear Bits 21-28 (F21-F28) 0b00011111111111111111111111111111, // Clear Bits 29-31 (F29-F31) }; float two_std_dev(const float arr[], uint32_t length); void adc_offset_adjustment(uint32_t length); void acknowledge(); void verify_cv_bit(uint16_t cv_address,bool bit_val, uint8_t bit_pos); void verify_cv_byte(uint16_t cv_address, uint8_t cv_data); void regular_cv_write(uint16_t cv_index, uint8_t cv_data); //void write_cv_handler(uint16_t cv_index, uint8_t cv_data); #define ProgramInstrVerifyBit 0b10 #define ProgramInstrVerifyByte 0b01 #define ProgramInstrWriteByte 0b11 #define ProgramCmd(instr, adrmsbits) ((instr<<2) | (adrmsbits)) /*! * \brief CV Programming mode function * Used on entering programming mode in order to write CV values to persistent flash memory or verify/read bits/bytes from flash.
* Refers to NMRA Standard 9.2.3 ("Service Mode Programming") or RCN-216
* * Procedure: * 1. Checks for valid programming command * 2. Disables core1 timers * 3. Resets core1 * 4. Saves interrupts * 5. Evaluates the type of programming instruction Write byte / Verify byte / Verify bit and runs corresponding function * 6. Restores interrupts * 7. Launch core1 * * \param number_of_bytes Number of bytes in byte_array[] * \param byte_array Pointer to byte_array[] */ void program_mode(uint8_t number_of_bytes, const uint8_t byte_array[]); void set_outputs(uint32_t functions_to_set_bitmask); void update_active_functions(uint32_t new_function_bitmask, uint8_t clr_bit_ind, bool direction_change); bool error_detection(int8_t number_of_bytes, const uint8_t * byte_array); bool is_long_address(uint8_t number_of_bytes, const uint8_t byte_array[]); bool address_evaluation(uint8_t number_of_bytes,const uint8_t byte_array[]); void instruction_evaluation(uint8_t number_of_bytes,const uint8_t byte_array[]); bool reset_message_check(uint8_t number_of_bytes, const uint8_t *const byte_array); int8_t verify_dcc_message(); void bits_to_byte_array(int8_t number_of_bytes,uint8_t byte_array[]); void evaluate_message(); void track_signal_rise(unsigned int gpio, long unsigned int events); void track_signal_fall(unsigned int gpio, long unsigned int events); /*! * \brief Output initialization function * * Initializes all allowed GPIO outputs as outputs
* Sets PWM functionality for GPIOs configured as PWM pins CV_112 - CV_115 (see CV.h for reference)
* PWM frequency and clock divider are configured according to CV_116 - CV_171 (see CV.h for reference)
*/ void init_outputs(); /*! * \brief Measures base pwm duty cycles at which the motor barely starts moving. * * Function starts with 1/20 of the maximum duty cycle then increases the duty cycle by 1/500 of the maximum until * the motor movement can be measured. This is done for the specified amount of iterations. * The array with raw measurements values is then passed to two_std_dev() in order to detect outliers and * calculate the average.An additional correction factor is applied and the overall measurement result is then * returned. In case no motor movement could be measured a value of 0 is returned and normally written to flash, * indicating a pending calibration next time the decoder starts, rerunning the calibration. * \param direction Specifies direction which is to be measured * \param iterations Specifies the amount of iterations the measurement is to be repeated and averaged out over * \return Measurement */ uint16_t measure_base_pwm(bool direction, uint8_t iterations); /*! * \brief Checks various CV values in order to detect factory condition or pending calibrations * * Procedure: * 1. Check for flash memory factory condition when found write default values specified in CV.h to flash memory * 2. Check for existing ADC offset setup when not found write 7 to read-only CV_7 in order to trigger a ADC offset measurement/calibration * 3. Check for base PWM configuration/calibration, run calibration when none is found */ void cv_setup_check(); /*! * \brief Function initializes motor PWM for pin specified * \param gpio GPIO pin */ void init_motor_pwm(uint8_t gpio); /*! * \brief Initializes ADC * * Function initializes ADC, corresponding GPIO pins and ADC FIFO */ void init_adc();