////////////////////////// // RP2040-Decoder // // Gabriel Koppenstein // // core0.c // ////////////////////////// #include "core0.h" // XIP_BASE + FLASH_TARGET_OFFSET = "0x101FF000" <- This address need to be smaller than __flash_binary_end stored in RP2040-Decoder.elf.map const uint8_t *CV_ARRAY_FLASH = (const uint8_t *) (XIP_BASE + FLASH_TARGET_OFFSET); uint64_t input_bit_buffer = 0; uint16_t level_table[32] = {0}; absolute_time_t falling_edge_time,rising_edge_time; // Function returns average of values deviating less than twice the standard deviation from original average float two_std_dev(const float arr[], uint32_t length){ // Calculate arithmetic average float sum = 0; for (uint32_t i = 0; i < length; ++i) { sum += arr[i]; } float x_avg = sum / (float)length; // Calculate sample variance and sampled standard deviation sum = 0; for (uint32_t i = 0; i < length; ++i) { sum += (arr[i]-x_avg)*(arr[i]-x_avg); } float variance = sum / (float)(length-1); float std_dev = sqrtf(variance); // Sum every element that is within two times the sampled standard deviation and compute new average sum = 0; uint32_t counter = 0; for (uint32_t i = 0; i < length; ++i) { float diff = fabsf(arr[i]-x_avg); if ( diff < std_dev*2.0f ){ sum += arr[i]; counter++; } } return sum / (float)counter; } // Measures constant adc offset and programs the offset into flash void adc_offset_adjustment(uint32_t n){ LOG(1, "adc_offset_adjustment\n"); float offsets_fwd[n]; float offsets_rev[n]; // Set PWM level to 0 just to be sure pwm_set_gpio_level(MOTOR_FWD_PIN, 0); pwm_set_gpio_level(MOTOR_REV_PIN, 0); busy_wait_ms(1000); // Measure n times in "reverse direction" (GPIO 28) adc_select_input(2); adc_run(true); for (uint32_t i = 0; i < n; i++) { offsets_rev[i] = (float)adc_fifo_get_blocking(); } adc_run(false); adc_fifo_drain(); busy_wait_ms(1000); // Measure n times in "forward direction" (GPIO 29) adc_select_input(3); adc_run(true); for (uint32_t i = 0; i < n; i++) { offsets_fwd[i] = (float)adc_fifo_get_blocking(); } adc_run(false); adc_fifo_drain(); // Find overall average discarding outliers in measurement float offset_avg_fwd = two_std_dev(offsets_fwd, n); float offset_avg_rev = two_std_dev(offsets_rev, n); float overall_avg = (offset_avg_fwd+offset_avg_rev)/2; uint8_t offset = (uint8_t)roundf(overall_avg); LOG(1, "new adc offset CV[171] (%f): (uint8_t)%d\n", overall_avg, offset); // Create temporary array -> change CV 172 in temp array -> erase flash -> write temp array to flash uint8_t CV_ARRAY_TEMP[CV_ARRAY_SIZE]; memcpy(CV_ARRAY_TEMP, CV_ARRAY_FLASH, sizeof(CV_ARRAY_TEMP)); CV_ARRAY_TEMP[171] = offset; flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE); flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_TEMP, FLASH_PAGE_SIZE * 2); } // Confirmation after writing or verifying a CV // Works by creating a spike in current consumption, this is detected by the command station void acknowledge() { uint16_t max_lvl = _125M/(CV_ARRAY_FLASH[8]*100+10000); pwm_set_gpio_level(MOTOR_FWD_PIN, max_lvl); busy_wait_ms(3); pwm_set_gpio_level(MOTOR_FWD_PIN, 0); pwm_set_gpio_level(MOTOR_REV_PIN, max_lvl); busy_wait_ms(3); pwm_set_gpio_level(MOTOR_REV_PIN, 0); } // When bit matches sent byte -> acknowledge() void verify_cv_bit(uint16_t cv_address,bool bit_val, uint8_t bit_pos) { uint8_t mask = 0b00000001; bool res = ( (CV_ARRAY_FLASH[cv_address] >> bit_pos) &mask ) == bit_val; if (res) { acknowledge(); } } // When byte matches sent byte -> acknowledge() void verify_cv_byte(uint16_t cv_address, uint8_t cv_data){ if (CV_ARRAY_FLASH[cv_address] == cv_data) acknowledge(); } // CV writing function first erases necessary amount of blocks in flash and then rewrites to flash void regular_cv_write(uint16_t cv_index, uint8_t cv_data){ uint8_t CV_ARRAY_TEMP[CV_ARRAY_SIZE]; memcpy(CV_ARRAY_TEMP, CV_ARRAY_FLASH, sizeof(CV_ARRAY_TEMP)); CV_ARRAY_TEMP[cv_index] = cv_data; flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE); flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_TEMP, FLASH_PAGE_SIZE * 2); acknowledge(); } // There are some exceptions to writing CVs - e.g. writing to a read only CV is not valid - this gets handled here void write_cv_handler(uint16_t cv_index, uint8_t cv_data){ switch (cv_index) { case 0: //CV_1 // CV_1 => Value = 0 is not allowed if (cv_data == 0 || cv_data > 127) break; else regular_cv_write(cv_index,cv_data); break; case 6: //CV_7 // Read only (CV_7 - Version no.) // ADC offset Adjustment (CV_7; Value = 7); if (cv_data == 7) { LOG(1, "trigger adc offset adjustment via cv7 => 7\n"); adc_offset_adjustment(8192); } break; case 7: //CV_8 // Read only (CV_8 - Manufacturer ID) // Reset all CVs to Default (CV_8; Value = 8) if (cv_data == 8){ LOG(1, "reset of flash triggered via cv8 => 8\n"); flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE); flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_DEFAULT, FLASH_PAGE_SIZE * 2); } break; // CV_17 must have a value between 11000000->(192dec) and 11100111->(231dec) inclusive // CV_17 == 192 && CV_18 == 0 -> Address = 0 is also not valid and therefore shall not be set case 16: //CV_17 if ( (cv_data < 192 || cv_data > 231) || (CV_ARRAY_FLASH[17] == 0 && cv_data == 192) ) break; else regular_cv_write(cv_index,cv_data); break; case 17: //CV_18 if(CV_ARRAY_FLASH[16] == 192 && cv_data == 0) break; else regular_cv_write(cv_index,cv_data); break; // CV_31 & CV_32 Index high byte isn't implemented and shall not be set case 30: //CV_31 case 31: //CV_32 break; // Regular CV write is carried out default: regular_cv_write(cv_index,cv_data); } } // CV Programming function resets core1 and evaluates the type of programming instruction (e.g. write byte) void program_mode(uint8_t number_of_bytes, const uint8_t * const byte_array) { //First check for valid programming command ("address" 112-127) if (byte_array[number_of_bytes - 1]<128 && byte_array[number_of_bytes - 1]>111) { uint8_t instruction_type_mask = 0b00001100; uint8_t instruction_type = instruction_type_mask & byte_array[number_of_bytes - 1]; uint8_t cv_address_ms_bits_mask = 0b00000011; uint16_t cv_address_ms_bits = cv_address_ms_bits_mask & byte_array[number_of_bytes - 1]; uint16_t cv_address = byte_array[number_of_bytes - 2] + (cv_address_ms_bits << 8); // Before accessing flash, timers and interrupts need to be disabled and core1 needs to be shut down. if(pid_control_timer.pool) alarm_pool_destroy(pid_control_timer.pool); if(speed_helper_timer.pool) alarm_pool_destroy(speed_helper_timer.pool); multicore_reset_core1(); uint32_t saved_interrupts = save_and_disable_interrupts(); // Verify CV bit instruction if (instruction_type == 0b000001000) { uint8_t bit_pos_mask = 0b00000111; uint8_t bit_pos = bit_pos_mask&byte_array[number_of_bytes - 3]; uint8_t bit_val_mask = 0b00000001; uint8_t bit_val_uint = (byte_array[number_of_bytes - 3]>>3) & bit_val_mask; bool bit_val = bit_val_uint; verify_cv_bit(cv_address, bit_val, bit_pos); } // Verify CV byte instruction else if (instruction_type == 0b000000100) { uint8_t cv_data = byte_array[number_of_bytes - 3]; verify_cv_byte(cv_address, cv_data); } // Write CV byte instruction else if (instruction_type == 0b000001100) { uint8_t cv_data = byte_array[number_of_bytes - 3]; write_cv_handler(cv_address, cv_data); } // Restore interrupts restore_interrupts(saved_interrupts); busy_wait_ms(5); } } // Set outputs according to configuration (PWM on/off, PWM duty cycle/level, ...) void set_outputs(uint32_t functions_to_set_bitmask) { // Get outputs with pwm enabled and preset outputs_to_set_PWM variable with resulting GPIO Bitmask uint32_t PWM_enabled_outputs = get_32bit_CV(111); uint32_t outputs_to_set_PWM = PWM_enabled_outputs; // Get enabled output configuration corresponding to set functions and direction uint32_t outputs_to_set = 0; uint32_t temp_mask = 1; for (uint8_t i = 0; i < 32; i++) { if (temp_mask & functions_to_set_bitmask ){ outputs_to_set |= get_32bit_CV(i * 8 + 260 - 4 * get_direction(0)); } temp_mask<<=1; } outputs_to_set_PWM &= outputs_to_set; // Outputs with PWM to be enabled outputs_to_set &= ~outputs_to_set_PWM; // Outputs without PWM to be enabled // Set regular outputs without PWM, preventing illegal GPIO by masking with GPIO_ALLOWED_OUTPUTS gpio_put_masked(GPIO_ALLOWED_OUTPUTS, outputs_to_set); // Set PWM enabled outputs to desired level temp_mask = 1; for (uint8_t i = 0; i < 32; ++i) { if(temp_mask & outputs_to_set_PWM){ pwm_set_gpio_level(i, level_table[i]); pwm_gpio_to_channel(i); pwm_gpio_to_slice_num(i); } else if (temp_mask & PWM_enabled_outputs){ pwm_set_gpio_level(i,0); } temp_mask<<=1; } } // Update functions F0 - F31 when function command is received or in case of direction change void update_active_functions(uint32_t new_function_bitmask, uint8_t clr_bit_ind, bool direction_change) { static uint32_t active_functions; static uint32_t prev_active_func; // Outputs depend on direction // In case of a direction change every output needs to be set according to configuration for the other direction if (direction_change) set_outputs(active_functions); // In case of a change in active functions only the function group corresponding to the instruction is considered // Check for changes and set outputs accordingly else{ new_function_bitmask &= ~(clr_bit_arr[clr_bit_ind]); // Clear every bit except bits corresponding to group of functions active_functions &= clr_bit_arr[clr_bit_ind]; // Clear bits corresponding to group of functions active_functions |= new_function_bitmask; // Write bits corresponding to group of functions uint32_t changes = active_functions ^ prev_active_func; // Checks for changes from previous state if(changes) set_outputs(active_functions); prev_active_func = active_functions; } } // Bitwise XOR for all Bytes -> Successful result is: "0000 0000" bool error_detection(int8_t number_of_bytes, const uint8_t * const byte_array) { uint8_t xor_byte = 0; for (int i = 0; i < number_of_bytes; i++) { xor_byte = xor_byte ^ byte_array[i]; } return (0 == xor_byte); } // Check for long address. Function returns true for long address. bool is_long_address(uint8_t number_of_bytes, const uint8_t * const byte_array) { if ((byte_array[number_of_bytes - 1]>>6) == 0b00000011) return true; return false; } // First checks for idle package and then evaluates address included in byte_array[] bool address_evaluation(uint8_t number_of_bytes,const uint8_t * const byte_array) { // Check for Idle Package if (byte_array[number_of_bytes - 1] == 255) { return false; } // Long/extended address decoder configuration (CV_29 Bit5) bool CV_29_bit5 = (CV_ARRAY_FLASH[28]&0b00100000)>>5; uint16_t read_address; // Decoder configured to receive long/extended address if (CV_29_bit5){ // Package received does contain a long address -> Check for accordance if (is_long_address(number_of_bytes, byte_array)) { // start of transmission -> address_byte_1 -> address_byte_0 -> ... -> end of transmission uint16_t address_byte_1 = (byte_array[number_of_bytes - 1]) - 192; // Remove long address identifier bits uint16_t address_byte_0 = (byte_array[number_of_bytes - 2]); read_address = (address_byte_1 << 8) + address_byte_0; uint16_t long_address = get_16bit_CV(16) & 0x3FFF; // &Mask to remove long address identifier bits return (long_address == read_address); } // Package received does not contain a long address else return false; } // Short address decoder configuration (CV_29 Bit5) else { // Short Address Package // start of transmission -> address_byte_0 -> ... -> end of transmission read_address = (byte_array[number_of_bytes - 1]); return (CV_ARRAY_FLASH[0] == read_address); } } // Evaluate the type of instruction void instruction_evaluation(uint8_t number_of_bytes,const uint8_t * const byte_array) { // start of transmission -> ... -> command_byte_n -> ... -> command_byte_0 -> ... -> end of transmission // The position of command bytes depend on whether the address is long or not uint8_t command_byte_n; uint8_t command_byte_start_index; if (is_long_address(number_of_bytes,byte_array)) { command_byte_start_index = number_of_bytes - 3; } else { command_byte_start_index = number_of_bytes - 2; } command_byte_n = byte_array[command_byte_start_index]; //0011-1111 (128 Speed Step Control) - 2 Byte length if (command_byte_n == 0b00111111){ static bool prev_dir; uint32_t speed_step = byte_array[command_byte_start_index - 1]; // LOG(1, "new speed %d", speed_step); multicore_fifo_push_blocking(speed_step); // LOG(1, " submitted to list\n"); // In case of a direction change, functions need to be updated because functions might depend on direction state if (get_direction(0) != prev_dir) { update_active_functions(0,0,true); prev_dir = get_direction(0); } } // 10XX-XXXX (Function Group Instruction) else if (command_byte_n >> 6 == 0b00000010){ switch (command_byte_n >> 4) { case 0b00001011: // F5-F8 update_active_functions((command_byte_n << 5),1,false); break; case 0b00001010: // F9-F12 update_active_functions((command_byte_n << 9),2,false); break; default: // F0-F4 update_active_functions(((command_byte_n << 1) + (command_byte_n >> 4)),0,false); break; } } //Feature Expansion Instruction 110X-XXXX else if (command_byte_n >> 5 == 0b00000110) { switch (command_byte_n) { case 0b11011110: // F13-F20 update_active_functions((byte_array[command_byte_start_index - 1] << 13),3,false); break; case 0b11011111: // F21-F28 update_active_functions((byte_array[command_byte_start_index - 1] << 21),4,false); break; case 0b11011000: // F29-F31 update_active_functions((byte_array[command_byte_start_index - 1] << 29),5,false); break; default: break; } } } // Check for reset package - When reset package is found stop the motor and disable all functions bool reset_package_check(uint8_t number_of_bytes,const uint8_t * const byte_array){ if (byte_array[number_of_bytes-1] == 0b00000000 && byte_array[number_of_bytes-2] == 0b00000000){ uint32_t speed_step = 1; multicore_fifo_push_blocking(speed_step); // Emergency Stop update_active_functions(0,0,0); // Disables all functions return true; } else return false; } // Checks for valid package - looking for correct preamble int8_t check_for_package() { //returns number of bytes if valid bit-pattern is found. Otherwise -1 is returned. uint64_t package3Masked = input_bit_buffer & PACKAGE_MASK_3_BYTES; if (package3Masked == PACKAGE_3_BYTES) return 3; uint64_t package4Masked = input_bit_buffer & PACKAGE_MASK_4_BYTES; if (package4Masked == PACKAGE_4_BYTES) return 4; uint64_t package5Masked = input_bit_buffer & PACKAGE_MASK_5_BYTES; if (package5Masked == PACKAGE_5_BYTES) return 5; return -1; } //start of transmission -> byte_n(address byte) -> ... -> byte_0(error detection byte) -> end of transmission void bits_to_byte_array(int8_t number_of_bytes,uint8_t byte_array[]) { for (uint8_t i = 0; i < number_of_bytes; i++) { byte_array[i] = input_bit_buffer >> (i * 9 + 1); } } // Sequence of bits gets evaluated void evaluation(){ static bool core1_launched = false; static bool reset_package_flag; int8_t number_of_bytes = check_for_package(); // number_of_bytes contains the amount of bytes when the package is valid, otherwise -1 if (number_of_bytes != -1) { // Split data into 8Bit array uint8_t byte_array[SIZE_BYTE_ARRAY] = {0}; bits_to_byte_array(number_of_bytes,byte_array); // Check for errors if (error_detection(number_of_bytes,byte_array)) { // Check for matching address if (address_evaluation(number_of_bytes,byte_array)) { reset_package_flag = false; if (!core1_launched){ multicore_launch_core1(core1_entry); // Wait for pid.direction pointer via multicore fifo also signalizing that core1 initialization is finished. get_direction((bool *) multicore_fifo_pop_blocking()); core1_launched = true; } instruction_evaluation(number_of_bytes,byte_array); } // When previous packet was a reset package -> enter program mode else if (reset_package_flag) { program_mode(number_of_bytes,byte_array); } // Check for reset package and set flag when reset package is received else { reset_package_flag = reset_package_check(number_of_bytes,byte_array); } } } } // DCC-Signal (GPIO 21) rising edge interrupt void track_signal_rise(unsigned int gpio, long unsigned int events) { // Save current timer value rising_edge_time = get_absolute_time(); // Disable rising edge interrupt and enable falling edge interrupt gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE, false, &track_signal_rise); gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_FALL, true, &track_signal_fall); } // DCC-Signal (GPIO 21) falling edge interrupt void track_signal_fall(unsigned int gpio, long unsigned int events) { // Save current timer value falling_edge_time = get_absolute_time(); // Time difference is equal to the time the signal was in a logical high state int64_t time_logical_high = absolute_time_diff_us(rising_edge_time,falling_edge_time); // When logical high was longer than 87us write 0 bit into buffer otherwise 1 bool bit; if(time_logical_high > 87) bit = 0; else bit = 1; input_bit_buffer <<= 1; input_bit_buffer |= bit; // evaluate sequence of bits saved in buffer evaluation(); // Disable falling edge interrupt and enable rising edge interrupt gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_FALL, false, &track_signal_fall); gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE, true, &track_signal_rise); } // Output initialization function - Configures pwm frequency and clock divider according to CV_111 - CV_171 void init_outputs(){ gpio_init_mask(GPIO_ALLOWED_OUTPUTS); gpio_set_dir_out_masked(GPIO_ALLOWED_OUTPUTS); // Note: This might also disable UART on GPIO0 & GPIO1 uint32_t PWM_enabled_outputs = get_32bit_CV(111) & GPIO_ALLOWED_OUTPUTS; uint32_t slice, channel; uint16_t wrap, level; uint8_t clock_divider; uint32_t mask = 1; for (uint8_t i = 0; i < 32; ++i) { if (PWM_enabled_outputs & mask){ slice = pwm_gpio_to_slice_num(i); channel = pwm_gpio_to_channel(i); // Channel A = "0"; Channel B = "1" wrap = get_16bit_CV(115 + 7*slice); level = get_16bit_CV(118 + 7*slice + 2*channel); clock_divider = CV_ARRAY_FLASH[117+7*slice] + 1; gpio_set_function(i,GPIO_FUNC_PWM); pwm_set_wrap(slice,wrap); pwm_set_gpio_level(i,0); level_table[i] = level; pwm_set_clkdiv_int_frac(slice,clock_divider,0); pwm_set_enabled(slice,true); } mask<<=1; } } // Measures "base" pwm duty cycle needed to overcome friction uint16_t measure_base_pwm(bool direction, uint8_t iterations){ uint gpio; if (direction) gpio = MOTOR_FWD_PIN; else gpio = MOTOR_REV_PIN; float level_arr[iterations]; for (int i = 0; i < iterations; ++i) { uint16_t max_level = _125M/(CV_ARRAY_FLASH[8]*100+10000); uint16_t level = max_level/20; LOG(1, "iteration %d: maxlevel %d level %d\n", i, max_level, level); float measurement; do { pwm_set_gpio_level(gpio, level); busy_wait_ms(30); level += max_level/500; measurement = measure(CV_ARRAY_FLASH[60], CV_ARRAY_FLASH[61], CV_ARRAY_FLASH[62], CV_ARRAY_FLASH[63], direction); // Abort measurement and write default value of 0 to flash LOG(1, "level %d measurement %f loop-cond: %f\n", level, measurement, measurement-(float)CV_ARRAY_FLASH[171]); if (level > max_level) { LOG(1, "measure_base_pwm: abort measurement and return 0\n"); return 0; } } while((measurement - (float)CV_ARRAY_FLASH[171]) < 5.0f); LOG(1, "level_arr[%d] = %f\n", i, level); level_arr[i] = (float)level; busy_wait_ms(100); } // Find and return overall average discarding outliers in measurement - multiply with 0.9 float retVal = 0.9f*two_std_dev(level_arr,5); printf("measure_base_pwm: %d(%f)\n", (uint16_t)retVal, retVal); return (uint16_t)(retVal); } // Check for flash memory factory condition and adc offset setup // When factory condition is found the CV_ARRAY_DEFAULT will be written into flash // When ADC Setup is not configured run adc offset adjustment function and write adc offset into flash void cv_setup_check(){ // Check for flash factory setting and set CV_FLASH_ARRAY to default values when factory condition ("0xFF") is found. // if ( CV_ARRAY_FLASH[64] == 0xFF ){ if(1) { LOG(1, "found cv[64] equals to 0xff, reseting CVs (and CV[8] = 8)\n"); uint8_t arr[4] = {125,8,7,124}; program_mode(4,arr); //reset to CV_ARRAY_DEFAULT (write CV_8 = 8) } // Check for adc offset setup if ( CV_ARRAY_FLASH[171] == 0xFF ){ LOG(1, "found cv[171] equals to 0xff, adc offset adjstments (and cr[7] = 7)\n"); uint8_t arr[4] = {125,7,6,124}; program_mode(4,arr); //ADC offset adjustment (write CV_7 = 7) } // Check for base PWM configuration - used for feed-forward // Forward Direction if (get_16bit_CV(175) == 0){ LOG(1, "found cv[175] equals to 0, forward direction\n"); uint16_t base_pwm_fwd = measure_base_pwm(true,10); uint8_t base_pwm_fwd_high_byte = base_pwm_fwd>>8; uint8_t base_pwm_fwd_low_byte = base_pwm_fwd&0x00FF; uint8_t arr0[4] = {125,base_pwm_fwd_high_byte,175,124}; program_mode(4,arr0); uint8_t arr1[4] = {125,base_pwm_fwd_low_byte,176,124}; program_mode(4,arr1); } // Reverse Direction if (get_16bit_CV(177) == 0){ LOG(1, "found cv[177] equals to 0, reverse direction\n"); uint16_t base_pwm_rev = measure_base_pwm(false,10); uint8_t base_pwm_rev_high_byte = base_pwm_rev>>8; uint8_t base_pwm_rev_low_byte = base_pwm_rev&0x00FF; uint8_t arr0[4] = {125,base_pwm_rev_high_byte,177,124}; program_mode(4,arr0); uint8_t arr1[4] = {125,base_pwm_rev_low_byte,178,124}; program_mode(4,arr1); } LOG(1, "int_lim_max %d\n", CV_ARRAY_FLASH[51]); LOG(1, "int_lim_min %d\n", CV_ARRAY_FLASH[52]); } // This function ensures that the direction pointer can only be written once. // After first initialization this function can be called with arbitrary input to get the current direction bool get_direction(bool *direction_ptr){ static bool set_flag; static bool *dir_ptr; if(!set_flag) { dir_ptr = direction_ptr; set_flag = true; } return *dir_ptr; } // Motor PWM initialization void init_motor_pwm(uint8_t gpio) { uint16_t wrap_counter = (_125M/(CV_ARRAY_FLASH[8]*100+10000)) - 1; uint32_t slice_num = pwm_gpio_to_slice_num(gpio); pwm_set_clkdiv_int_frac(slice_num,CV_ARRAY_FLASH[173],0); pwm_set_wrap(slice_num, wrap_counter); pwm_set_gpio_level(gpio,0); pwm_set_enabled(slice_num, true); } // Main initialization - GPIO Config / ADC Config void init_main(){ if(gpio_get_function(MOTOR_FWD_PIN) != 4){ gpio_set_function(MOTOR_FWD_PIN, GPIO_FUNC_PWM); gpio_set_function(MOTOR_REV_PIN, GPIO_FUNC_PWM); adc_init(); adc_gpio_init(FWD_V_EMF_ADC_PIN); adc_gpio_init(REV_V_EMF_ADC_PIN); adc_fifo_setup(true,false,0,false,false); } } int main() { stdio_init_all(); LOG(0, "\n\n======\ncore0 init\n"); init_main(); LOG(1, "init motor pwms\n"); init_motor_pwm(MOTOR_FWD_PIN); init_motor_pwm(MOTOR_REV_PIN); LOG(1, "check cvs\n"); cv_setup_check(); LOG(1, "init outputs\n"); init_outputs(); LOG(1, "init gpios\n"); gpio_init(DCC_INPUT_PIN); gpio_set_dir(DCC_INPUT_PIN, GPIO_IN); gpio_pull_up(DCC_INPUT_PIN); gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE, true, &track_signal_rise); LOG(0, "core0 done\n"); while (1); }