/*! * * \file shared.h * Used by both cores * */ #pragma once #include "string.h" #include "pico/float.h" #include "pico/stdlib.h" #include "pico/multicore.h" #include "pico/printf.h" #include "hardware/pwm.h" #include "hardware/adc.h" #include "hardware/flash.h" // here you can enable printf debugging (needs extra soldering and you have to enable uart in the cmake configuration) // please note // - if it's disabled it will be compiled completely out // - be careful that printf debugging can change your timing behavior, for example in the pid controller limit the outputs // like already done (only print every 100th iteration for example!) // - also note that with logging enabled GPIO0/1 are DISABLED from decoder functions because they are used for uart to the // outside world (this is configure automatically for you below!) // - IMPORTANT: you have to enable uart in the cmakelists.txt to enable logging! #define LOGLEVEL 0 #define LOG(level, ...) { if(level <= LOGLEVEL) {printf(__VA_ARGS__);}} // Constant Value of 125 x 10^6 #define _125M 125000000 // GPIO used for DCC-Signal, Motor PWM or ADC #define DCC_INPUT_PIN 21u #define MOTOR_FWD_PIN 23u #define MOTOR_REV_PIN 22u #define FWD_V_EMF_ADC_PIN 28u #define REV_V_EMF_ADC_PIN 29u // if logging is enabled do NOT use gpio0/1 for functions in the decoder #if LOGLEVEL != 0 // GPIO used directly (GPIO 2-5 incl.) as outputs or to switch auxiliary output transistors (GPIO 24-27 incl.) #define GPIO_OUTPUT_PIN_MASK (1u<<24) | (1u<<25) | (1u<<26) | (1u<<27) | (1u<<5) | (1u<<4) | (1u<<3) | (1u<<2) #else // GPIO used directly (GPIO 0-5 incl.) as outputs or to switch auxiliary output transistors (GPIO 24-27 incl.) #define GPIO_OUTPUT_PIN_MASK (1u<<24) | (1u<<25) | (1u<<26) | (1u<<27) | (1u<<5) | (1u<<4) | (1u<<3) | (1u<<2) | (1u<<1) | (1u<<0) #endif // GPIO pin mask to prevent setting illegal GPIOs (ADC, Motor, DCC Input Pin) #define GPIO_ILLEGAL_MASK (1u< * Refers to "128 Speed Control" - NMRA Standard 9.2.1 section 2.3.2.1 or RCN-212 section 2.2.2.
* * The following speed steps exist: * * DEC | BIN | DIRECTION | DEFINITION * * 000 | 0000 0000 | Reverse | STOP * * 001 | 0000 0001 | Reverse | EMERGENCY STOP * * 002 | 0000 0010 | Reverse | Speed step 001 (Lowest speed) * * 003 | 0000 0011 | Reverse | Speed step 002 * * 004 | 0000 0100 | Reverse | Speed step 003 * * ... | .... .... | Reverse | ..... * * ... | .... .... | Reverse | ..... * * ... | .... .... | Reverse | ..... * * 126 | 0111 1110 | Reverse | Speed step 125 * * 127 | 0111 1111 | Reverse | Speed step 126 (Full speed) * * 128 | 1000 0000 | Forward | STOP * * 129 | 1000 0001 | Forward | EMERGENCY STOP * * 130 | 1000 0010 | Forward | Speed step 001 (Lowest speed) * * 131 | 1000 0011 | Forward | Speed step 002 * * 132 | 1000 0100 | Forward | Speed step 003 * * ... | .... .... | Forward | ..... * * ... | .... .... | Forward | ..... * * ... | .... .... | Forward | ..... * * 254 | 1111 1110 | Forward | Speed step 125 * * 255 | 1111 1111 | Forward | Speed step 126 (Full speed) * * @param speed_step speed step byte * @return direction; false for reverse; true for forward; */ bool get_direction_of_speed_step(uint8_t speed_step);