# Hardware Description ## Overview ![Block Diagram](https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/Block_Diagram.svg) The above block diagram gives a general overview regarding the operation of components. For better illustration it has been divided into four functional blocks. Furthermore these functional blocks can be subdivided and will be explained below. * Input Stage - DCC Signal Level Shift - Bridge Rectifier & Voltage Regulator * Motor Driver - Motor Driver - Back EMF measurement (ADC) * General Purpose - GPIO - Auxillary output * Microcontroller - Flash memory - Crystal oscillator ## Characteristics | Parameter | Symbol | Minimum | Maximum | Unit | | ----------------------------------------------------- | -------------- | ------- | -------- | ---- | | Absolute max. DCC Input Voltage | VDCC | -25 | +25 | V | | Absolute max. GPIO Voltage(0) | VPIN | -0.5 | 3.3+0.5 | V | | Input Voltage High(0) | VIH | 2.145 | 3.6 | V | | Input Voltage Low(0) | VIL | 0 | 1.155 | V | | Total GPIO Current(0) | IIOVDD_MAX| | 50 | mA | | Absolute max. motor output current(1) | IMOTOR | | 2.8 | A | | Absolute max. auxillary output current(2) | IAUX | | 400 | mA | (0): According to: [RP2040 Datasheet](https://datasheets.raspberrypi.com/rp2040/rp2040-datasheet.pdf) (assuming VDD = 3.3V) (1): According to: [BDR6133 Datasheet](https://datasheet.lcsc.com/lcsc/2101211904_Bardeen-Micro--BDR6133_C2687793.pdf) (2): According to: [T2N7002BK Datasheet](https://datasheet.lcsc.com/lcsc/1810271831_TOSHIBA-T2N7002BK-LM_C146372.pdf) ## Input Stage ![Input Stage](https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/Input_Stage.svg) D1 Rectifies the DCC square-wave into +V, the amplitude is not critical as long as its within the 25V limit. The rectified voltage +V is then provided to the 3.3V voltage regulator (U1) and to the motor driver (U2). The MOSFET on the right effectively translates the rather high DCC voltage to a suitable level for the microcontroller to process. When Q1 is turned off GPIO21 is pulled high by the RP2040 internal pull-up resistor, as soon as Q1 gets turned on (VGS > VGS,th), GPIO21 gets pulled to GND potential. R1 and R2 ensure that VGS doesnt exceed ±20V. ## Motor Driver ![Motor Driver](https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/Motor_Driver.svg) The Motor Driver is a complete H-Bridge IC specifically made for DC-Motors. In order to control the motor, it is necessary to measure the back-EMF. This is done by the ADC which measures at Points ADC_EMF_A and ADC_EMF_B respectively. The two resistors are used as a voltage divider. ## Auxillary Output ![Auxillary Output](https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/Aux_Outputs.svg) Switching of loads up to a maximum of about ~400mA can be done using four N-Channel MOSFETS. They are switching on the low-side which means the load effectively gets connected to GND potential as the transistor starts to conduct. GPIO24 - GPIO27 are used. ## GPIO To switch lighter loads six soldering pads on the back side of the PCB are connected to GPIO0 - GPIO5 pins . Although not implemented yet they could theoretically be used as inputs as well (e.g. Reed switch). ## Microcontroller ![Microcontroller](https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/Microcontroller.svg) The Microcontroller needs a crystal oscillator to function properly. External flash memory is also needed as it holds the configuration variables and the program itself. R3 & C14 are used to filter ADC_AVDD (ADC Reference Voltage). ## Complete Schematic ![Complete schematic](https://github.com/1nct/RP2040-Decoder/blob/main/docs/svg/RP2040-Decoder.svg) BOM & Alternative Parts -------------------------- | Ref | Quantity | Value | Component Type | Component Name | Footprint | | ----------------------------------------------------- | -------------- | ------- | -------- | ---- |---- | | C1, C2, C5, C6, C14 | 5 | 10u | Ceramic Capacitor | / | 0603_1608Metric | | C3, C4, C7, C8, C9, C10, C11, C12, C13, C15 | 10 | 100n | Ceramic Capacitor | / | 0603_1608Metric | | C16, C17 | 2 | 33p | Ceramic Capacitor | / | 0603_1608Metric | | D1 | 1 | VRMS = 40V , IF = 2A | Bridge Rectifier | KMB24F | MBS (TO-269AA) | | Q1, Q2, Q3, Q4, Q5 | 5 | VDS = 60V , ID = 0.4A | N-Channel MOSFET |T2N7002BK | SOT-23 | | R1, R2, R5, R6 | 4 | 6k8 | Resistor | / | 0603_1608Metric | | R3 | 1 | 200 | Resistor | / | 0603_1608Metric | | R7, R8, R9 | 3 | 1k | Resistor | / | 0603_1608Metric | | U1 | 1 | VOUT = 3.3V | Low Dropout Voltage Regulator | HT7533S | SOT-23 | | U2 | 1 | I = 2.8A | H-Bridge driver | BDR6133 | SOIC-8 | | U3 | 1 | 64Mb | Serial Flash Memory | W25Q64JVSSIQ | SOIC-8 | | U4 | 1 | / | Raspberry Pi RP2040 Microcontroller | RP2040 | QFN-56-1EP_7x7mm_P0.4mm | | Y1 | 1 | f = 12MHz | Crystal Oscillator | X322512MSB4SI | Crystal_SMD_3225-4Pin_3.2x2.5mm | NOTE: Keep capacitor Vmax in mind! Alternatives for BDR6133: [PT5126A-S-TP](https://lcsc.com/product-detail/Motor-Driver-ICs_PTC-Princeton-Tech-PT5126A-S-TP_C162093.html) [PT2476](https://lcsc.com/product-detail/Motor-Driver-ICs_PTC-Princeton-Tech-PT2476_C481903.html) Alternative for HT7533S: [GS7533-33TR3](https://www.lcsc.com/product-detail/Linear-Voltage-Regulators-LDO_Gainsil-GS7533-33TR3_C7427372.html)